What to do when your Vacheron Constantin watch doesn t go?

Vacheron Constantin Watch After-Sales Service Center: 400-659-0877

If the lack of power causes the watch not to go, it is much easier. Replace the battery of the quartz watch on the go. Mechanical watches are mainly underpowered, and watches with manual winding movements should be wound at the same time every day as much as possible, so that the watch can work with sufficient energy in the next 24 hours.

Because the energy source of the automatic movement watch is the arm movement of the wearer, it does not need to be wound by hand under normal wear, only when the wearer's movement is not enough to replenish enough energy to the mainspring, the manual winding method can be used to make up for it, and the crown rotation is controlled within 20 turns when winding. A self-winding watch that has not been worn for more than 40 hours should be re-worn by turning the crown twenty times to reactivate the movement's drive.

Watch maintenance and repair can refer to 702, Xidan Joy City Office Building, Xicheng District, Beijing

7th Floor, West Joy City Office Building, No. 131 Xibei Street, Xicheng District, Beijing] will answer for you.

A simple mechanical watch is winded, the mechanical watch does not go when the first consideration of the clockwork is not enough, as long as the spring is full, as shown in the figure on the button on the edge of the mechanical watch, clockwise rotation of the button on the side of the clockwork, there is a magnetic sound, usually 30 times rotation means that the spring is full.

There is a roulette wheel in the automatic mechanical watch, which is driven by the rotation of the human wrist, the user must wear it every time, and have a certain amount of wrist activity.

There is also the quality problem of the watch or the long-term use of the parts is not good, the movement needs to be re-cleaned and oiled, you can go to the mechanical watch maintenance center, find a professional maintenance person to solve.

Vacheron Constantin, one of the world's most famous watch brands, was founded in 1755 in Geneva, Switzerland, and is the world's oldest and earliest watch manufacturer and one of the world's most famous watch manufacturers. Vacheron Constantin has made a significant contribution to the world of watchmaking by inheriting the best of Swiss watchmaking tradition, while also innovating many watchmaking techniques.

Vacheron Constantin watches are very powerful among many brands, but after a long time, with the influence of the living environment and the wearer's living habits, the phenomenon of time error will gradually occur. Let me tell you what other reasons why your watch is not on time?

1. The watch is magnetic: the watch is in too much contact with the magnetic field, which causes the watch to be magnetic, resulting in the inaccuracy of the watch. After magnetization, the watch may stop, slow down, or go fast. After the watch is magnetized, its magnetism does not retract on its own and requires demagnetization to return to normal.

2. Lack of maintenance: mechanical watches are kept every 2-3 years, and quartz watches are kept every 4-5 years. Watch maintenance requires a complete disassembly, cleaning, oiling, reassembly, calibration, and inspection of the movement; Repair or replace any moving parts or faults that are prone to wear and tear.

If the watch lacks maintenance, it can cause parts to wear out, oil to dry up, affect the watch's normal travel time, and make the watch appear fast and slow. Regular machine maintenance can effectively prevent the occurrence of various faulty watches.

3. Mechanical failure: Mechanical failure such as watch spring failure, escapement system failure, and parts sliding may cause the watch to appear fast or slow, so when the watch is walking abnormally, you can pull out the crown first, and then find a professional technician to repair and test your watch.

Of course, the speed of a mechanical watch can be caused by severe shocks, water ingress, etc. The reasons are complex and require maintenance technicians to perform maintenance on a case-by-case basis. Quartz watches are generally very accurate when walking and are not easily walked to breakdowns.

With proper maintenance, this can happen when the speed is slower than the rate at which the board fails or when a component is in poor contact.

Finally, it is recommended that you regularly visit a professional Vacheron Constantin repair center for regular maintenance when wearing your watch, as careful maintenance can not only make your watch look new, but also extend the service life of your watch.

Hello, glad to answer for you!

Reasons why the watch is not running accurately:

1. Insufficient power reserve. If the amount of exercise is small, it may also cause a lack of power reserve, so you can replenish the power by winding it manually, and then observe whether it continues to be fast or slow.

2. The watch has been hit or impacted, which may cause loose damage to the internal parts and may also cause the problem of running time.

3. The lack of oil in the movement or the wear and aging of the internal parts may cause the problem of running time, which needs to be maintained.

4. The watch is magnetized: If the hairspring of the watch is magnetized, the watch will not be accurate. The influence of the wearer's usage habits may cause an increase in the time error. It is recommended to send it to a repair center for inspection and adjustment, which can restore the watch to the normal error range.

Top 5 reasons why common watches are inaccurate:

1) Insufficient power reserve: You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is very small, it may also cause insufficient power reserve, you can replenish the power by manual winding, and then observe whether it continues to have the phenomenon of fast and slow.

2) Insufficient power: If the quartz watch suddenly finds that it is slow, it is likely to be caused by insufficient battery energy, and you can send the watch to a special maintenance point to check the power.

3) Hit or hit: The watch is very tight, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause the problem of running time. This is to be dealt with in a timely manner.

4) Need to maintain: The lack of oil in the movement or the wear and aging of internal parts may cause time problems, which need to be maintained, and need to be sent to the designated maintenance point for maintenance services.

5) In addition to the above common situations, the watch is affected by some ambient temperatures: if the hairspring of the watch is magnetized, the watch will not be accurate.

If you have any questions, please call**, please feel free to call.

Watch does not go knowledge:

Home to think about whether it is because of the long-term processing of the watch stationary state does not go.

If the watch is in a stationary state for a long time, the watch will not automatically wind, which will make the watch lose the ability to move and stop walking. The above problem is actually very simple, users only need to swing the watch dozens of times to restore the time.

If you want to ensure the accuracy of automatic mechanical watches, you should wear them normally for more than 8 hours a day. Mechanical watches rely on the winding of the mainspring to provide power to make the watch move, and there are two ways to wind mechanical watches: one manual and one automatic. Due to the complex internal structure of the watch, and the phenotype is relatively heavy.

According to this characteristic, it is affected by a series of reasons such as gravity, temperature changes, and the use of mechanical friction.