How to connect the TV plug and where is the TV plug jack?

Hello! Are you referring to the power cord of the TV? Is the power cord broken or the plug broken?

If it is only the power cord that is broken, it is not difficult to peel off the plastic skin of the broken part of the power cord by 50mm and cut it off with scissors. There are three small wires of red, yellow and green (some are red, yellow and blue), which connect the wires of the same color together, and then use adhesive tape to wrap the parts of the copper wires firmly. If the plug is broken, just cut the plug off and buy a new triangle plug back.

It must be a triangular plug connecting to the ground wire. "Because one of the three wires of the TV power cord is connected to the ground wire, and the other two are the neutral line and the live wire, generally red is the live wire, yellow is zero, and now blue is the ground wire (there are also alternative cases where red means that the live wire is not yellow.) Yellow for the ground line, blue for the zero line).

When connected, the blue wire is connected directly above the plug, and the live wire and neutral wire are connected to the bottom and left and right positions respectively. After connecting, plug it into the power strip, turn on the TV, and see if it is powered on. If there is no power, do not move the red wire, change the position of the yellow and blue wires.

The TV plug is the same as the search for the ordinary power supply,Connection,The line inside hides the red wire and the green wire,The grounding wire should be connected according to the color,Then wrap it。

It is enough to grasp two key points, one is that the length of the stripped core should be appropriate, not too long, to prevent short circuits between contacts. Second, the fastening screws must be tightened to prevent the output voltage from being unstable and the joint from overheating caused by virtual connection and ignition.

I recommend that you don't connect the electrical plug yourself, and find a professional to help you install it.

I recommend calling a professional technician to do it.

I recommend finding a professional to come and pick it up.

The plug and jack of the TV are on the back of the TV:

The black one is the RF connector, which is plugged into the RF (Radio Frequency) input of the TV, which is the jack with a small iron pipe in the middle of the socket. That is, the antenna interface. The yellow one is the ** connector, and the red one is the audio connector.

The yellow connector is plugged into the yellow, white, and red set of the TV. Red can be inserted into yellow, white, red and white interfaces. With the yellow red line, there is no need to use the black line.

The jack of the TV plug is usually on the side or at the bottom, as this can improve the aesthetic effect as much as possible. As long as you look carefully, you will find it.

Today's TVs are flat-panel, and most of the various interfaces of TVs are on the side of the back or the bottom of the back.

If the TV is mounted on the wall, it is best to plug in all kinds of cables before installation.

Look at the directions next to it. If there are 6 of them, then 3 of them are signal output locations. If there is a plugged signal input, the 3 plugs in the color when it is plugged in. However, your *** or VCD should also be inserted into the color.

The cable on the back of the TV is wired as follows:

1. Connect the HDMI cable to the TV. Make a note of how the ports are labeled.

2. Connect the plug at the other end of the HDMI cable to the PC.

<>4. Open Settings and click System. The details are shown in the following figure:

<>6. Adjust the zoom and layout in the display. The details are shown in the following figure:

The cable on the back of the TV is wired as follows:

1. Connect the HDMI cable to the TV. Make a note of how the ports are labeled.

2. Connect the plug at the other end of the HDMI cable to the PC.

<>4. Open Settings and click System. The details are shown in the following figure:

<>6. Adjust the zoom and layout in the display. The details are shown in the following figure:

How to plug in the TV network connection line; 1、If the TV is connected to the wired network,You need to prepare a network cable,Insert one end of the network cable into the TV network interface,The other end is inserted into the routerLAN interface,So that the TV is connected to the wired network successfully,Turn on the TV to **Network program。 2、Generally, the TV should be set up after connecting to the wired network,So that the wired network can be used normally。 Zheng Bu first turned on the TV, so that the TV entered the main interface of network TV.

Use the TV's remote control to find the network settings on the TV's main interface, and then press the confirm button to enter. After entering the network settings interface, press the confirm button to enter. After entering, select the wired network connection, and set the TV to automatically obtain the IP address.

Once set up, the TV will automatically recognize the incoming network signal and obtain an IP address assigned by the router. After the TV obtains the IP address, it means that the TV has been successfully connected, and the user can return to the network TV interface, **** movie or TV series. 3、In the process of connecting the TV to the wired network,If the TV is not connected to the network,You can cut off the TV power and restart the router power,You can restore the router to factory settings,Re-set the relevant parameters of the router,You can also check whether the network cable is connected normally,You can also check the settings of the router、IP address and other parameter settings are correct,So that you can connect to the network mask。

As follows:

1. Prepare the required parts and materials.

2. Strip the line. 3. Make a head.

4. Fastening the ring.

5. Tighten. 6. Screw the butt.

Cable television (CATV), also known as cable television, is developed from wireless television and first appeared in Pennsylvania, USA in 1950. Cable TV still retains the broadcast standard and signal modulation mode of wireless TV, and does not change the basic performance of the TV system. Cable TV sends the recorded program to the user through a cable (cable or optical cable), and then uses the TV to replay it without radiating electromagnetic waves into the air, so it is also called closed-circuit television.

Cable TV is a type of pay-TV that is paid for by the viewer rather than the funder.

The line that comes in outdoors is the main line, buy a 2 distribution, 3 heads, the main line connects a separate head, and the 2 TV branch lines connect two outside 2 heads! If it is more troublesome to wrap the wire, pay attention to the copper wire and copper wire winding, aluminum wire and aluminum wire winding, do not put together, to separate winding, wrapping. As long as the workmanship is good, it doesn't make much difference!

It's not clear, what white is black, cable TV is a coaxial cable, the middle is a copper wire, the outside is a shielding net, if one of them is a signal line, then put two wires, copper wire together, shield one piece, don't short circuit on it.