What should I do if the pool water can t sink after putting a sedimentant?

If the pool water still can't settle after adding sedimentant, you can try the following methods:

2.Use precipitant propellants: Some precipitant propellants can enhance the effects of precipitants, making it easier to bind to contaminants and settle.

3.Use suspension thickeners: Some suspension thickeners can bring together sediment particles floating on the water, increasing their dead weight and making it easier to settle.

4.Check the water quality and chemical balance: Check the water quality and chemical balance parameters of the pool, such as pH, alkalinity and calcium hardness. If needed, these parameters can be adjusted to help improve the effectiveness of the precipitant.

5.Increase filtration time: Check and ensure that the pool filtration system is working properly and increase the filtration time to increase the chance of sediment contact with contaminants. Prolonged filtration may help to better remove the plankton.

6.Stirring water bodies: Stir water bodies using equipment such as a swimming pool's circulation system or agitator to help the sediment mix with contaminants and promote settling. Increasing the time and intensity of stirring will help to better disperse the precipitant.

If the problem still cannot be solved after trying the above methods, it is recommended to ask a professional for inspection and repair.

There are many swimming pool water quality managers have encountered such a problem: after putting the sedimentant, the sediment still does not sink and the sedimentation effect is still the next day, and there is still yellowing, and the swimming pool will not sink after putting the sedimentant? Brigade swimming pool basic condition:

1. Opening period: summer (May to October every year). 2. Swimming pool volume:

About 2,100 cubic metres of water (the deepest is 2.1 metres). 3. Water source: tap water.

4. Cycle cycle: The circulation system cannot be used, which means that there is no circulation leakage system. The use of water treatment chemicals at this stage:

1. Disinfectant: Stable chlorine preparation disinfectant (trichloroisocyanuric acid powder, dosing method: manually dilute the agent and throw it into the pool) 2. Other agents:

Alkali (sodium hydroxide, dosing method: directly thrown into the pool) 3. Polyaluminum chloride (dosing method: dissolved and diluted and thrown into the swimming pool) Swimming pool equipment:

1. Filtration equipment: It can't be used, when it's gone. 2. Disinfection equipment:

In the traditional way of dosing, the agent is diluted and thrown into the pool by hand. 3. Water quality line monitoring instrument: None 4. Other equipment:

Stainless steel submersible sewage suction machine.

Reasons for incomplete precipitation:

1) The algae killing, disinfection, and pH adjustment water treatment of the swimming pool are not done well.

2) The influence of external factors, such as rainy days, acid rain generally falls in the south in summer, which will affect the pH of the pool water and reduce the pH value of the pool water; In addition, rainwater can also bring dust, bacteria, and algae, which can also affect the disinfection effect, especially when it rains heavily, it is difficult to keep the pool water still, so that the sediment can float or cannot settle.

3) The amount of polyaluminum precipitant added is not properly controlled. If too much precipitant is added, it will produce a counterionic effect, which is difficult to coagulate and will float; The amount added is too small, it is difficult to form Gonghua, the coagulation effect is poor, and the suspended solids cannot be separated and precipitated.

4) The water temperature changes suddenly, and the water flow disturbance in the upper and lower layers causes the precipitant to float.

5) The precipitant bought does not contain enough chlorine, because many polyaluminum chloride precipitants on the market cannot reach 30% content, and some non-sinking or floating phenomena may occur when using these products.

Solution: 1) The swimming pool should be disinfected every day; Increase the pH level to about the left.

2) Do not add too much or too little precipitant, the general dosage is 1000 water cubes 5-10kg, if the precipitant can not be sucked clean, before the opening of the soaking again, so that the pool can be opened on the same day.

3) Before adding the precipitant to the pool, it should be diluted with water at a ratio of 1:3, if you want to add 5kg of precipitant, first add about 15kg of water to the bucket, and then slowly add the precipitant to the bucket, stir while adding, after all the addition is stirred, then add water to 150kg in the bucket and stir evenly to sprinkle into the pool.

4) After the end of the night, do the impact treatment again, and then detect and adjust the pH, and it is best to add a sufficient amount of swimming pool sediment for purification treatment.

5) If the weather is too hot, it may also affect the use of precipitant, so the precipitant is generally added after the end of the evening, so that the temperature is suitable for the time and sufficient.

6) It is recommended to buy a precipitant with a content of up to 30%.

There will be sediment in the swimming pool, how to get rid of it? The sediment in the swimming pool may be some impurities in the water, and I think it may also be the sediment of disinfectant, which is generally difficult to remove.

If, after dropping the precipitant, it is found that it cannot settle and floats on the water, it may be due to one of the following reasons:

Wrong choice of sedimenter: Different types of pools require the use of specific sedimenters. Make sure you choose the right sediment for your pool type and problem.

Insufficient precipitant: Not enough precipitant may not have been added to treat suspended solids in the water. Follow the instructions for use of the precipitant to ensure that the correct dosage is used with the best care.

Poor water circulation: There may be problems with the water circulation system, causing the precipitant to not mix adequately and come into contact with contaminants. Inspect filters, pumps, and other water circulation equipment to make sure they are working properly.

Water chemical balance issues: If the pH of the water is too high or too low, the precipitant may not work properly. Make sure that the pH of the water is within the appropriate range and that the necessary chemical adjustments are made.

If you find that the precipitant does not work, you can try the following:

Increase the dosage of precipitant: Increase the dosage of precipitant according to the product instructions to ensure safety. Remember to follow the directions carefully and avoid overuse.

Check the water circulation system: Make sure pumps, filters, and other water circulation equipment are working properly to promote an even distribution of the precipitant.

Adjust the chemical balance of water quality: Check and adjust the pH, alkalinity, and other important parameters of the water to keep them within the appropriate range. This may require the use of other water treatment agents or appropriate adjustments.

Consult a professional Qingkes: If the problem persists, it is recommended to consult a professional pool maintenance personnel or water treatment expert. They can provide personalized advice and solutions tailored to your specific situation.

Remember, safety is always a top priority when dealing with pool water quality issues. Always follow product instructions and safety operating procedures, and seek professional help if necessary.

After the pool is put into the sediment, it can't sink and floats on the water, what is the way to deal with it.

Good morning dear. If the sediment does not settle to the bottom of the pool effectively and floats on the water after the sediment is applied, you can try the following methods to deal with it:1

Stirring the water: Stirring the water using equipment such as a swimming pool's circulation system or agitator to help the sedimentant mix with the contaminants and promote the sedimentation. Increasing the time and intensity of stirring will help to better disperse the precipitant.

Prolonged filtration may help to better remove the plankton. 3.External Aids:

Consideration can be given to using the following methods to assist in the settling of the precipitator: - Use of precipitant propellant: Some precipitant propellants can enhance the effect of the precipitator, making it easier to bind to contaminants and settle.

Use suspension thickeners: Some suspension thickeners can bring together sedimentant particles that are floating on the water, increasing their dead weight and making them easier to settle. 4.

Adjust water quality and chemical balance: Check and adjust the water quality and chemical balance parameters of the pool, such as pH, alkalinity, and calcium hardness. The right water quality and chemical balance can help improve the effectiveness of the precipitant.

Generally, it is arranged to put the pool sediment in the evening, and use a manual sewage suction machine to suck up the sediment early in the morning. You can't drag it out late, because the sun will hit the pool, and the flocculent in the precipitation will float up again, affecting the water purification effect, so try to get up early in the morning to absorb dirt.

Generally, the pool sedimentant is used once every 5-7 days, or when the pool water is turbid. The dosage is 1000 cubic meters of water, and 5-10kg is put in. Before putting the pool sedimentant, the pH of the water should first be adjusted to the left and right.

Because the high pH value is conducive to the elimination of polar molecules in the water, so that the particulate suspended matter in the water is easy to settle. The most suitable pH range for the usual use of swimming pool sedimentant (polyaluminium chloride) is: In an alkaline environment, it can give full play to its hydroxyl bridging effect to accelerate condensation and sedimentation.

When using polyaluminum chloride, dissolve it with water first: use a bucket to hold more than 10 times the water, then slowly add polyaluminum chloride, stir while adding, and the polyaluminum chloride will soon dissolve in water. It is not possible to add polyaluminum chloride first and then add water, because in this way, polyaluminum chloride will agglomerate and be difficult to disperse and dissolve.

Polyaluminium chloride generates heat when dissolved, and the higher the calorific value, the better the quality. The dissolved polyaluminium chloride should be added to the swimming pool as soon as possible. Some swimming pools are added slowly by adding medicine pumps, and some are added directly at the water mouth, and the effect of direct addition is better than that of medicine pumps, but the workload of direct sewage suction will be larger.

The static precipitation time of the flocculant requires at least 6 hours, and it generally takes 6-8 hours to completely precipitate. If the pool water is deeper, the sediment will settle slower on the surface of the water. Therefore, in addition to adding more sedimentant, the deep pool also needs to give more settling time. ‍

After the swimming pool closes at night, add a precipitant to the pool, the commonly used precipitant is alum, etc., and then stir it well, and wait until the next morning to vacuum it. If you don't have an automatic vacuum cleaner, you can also make one, which is to use a pump to pump out the sediment and water at the bottom of the pool and discharge it into the drain!

Hello, after the pool is sprinkled with sediment, continuing to release water will have a certain impact on the water quality of the pool, because continuing to release water will resuspend the sediment in the water, increase the water turbidity, and reduce the temperature of the pool water, affecting the content of reactive oxygen species and the formation of volatile organic compounds in the sediment. In addition, if the sediment in the pool is not only sediment, but also some other organic substances, such as organic compounds, plant residues, etc., these substances will have a very significant impact through the process of water discharge, resulting in obvious turbidity and discoloration of the pool water. Therefore, in order to ensure that the water quality of the pool is good, it is necessary to carry out water replenishment work immediately after sprinkling sedimentation, which is not only to control the change in the water volume of the pool, but also to improve the water quality.