How to repair the Apollo Roman barrel, Apollo shower room repair phone

Such a problem is indeed unfair to consumers, service first When these situations occur, wouldn't it be good for the two parties to communicate well

I have a suggestion for your question:

Check first to see if the button lever is too short When pressing, it is not in place The drain valve is closed in advance, and the water output is small, which affects the flushing function Check this first to see if there is a problem with the accessories

You can also take off the ceramic cover first, and press the drain valve on the top of the tank accessories directly with your fingers Don't press it too quickly and lightly Press it a little heavier, and you don't need to press it for a few seconds, you need to press it to the bottom and then let go See how the situation is If the flush is okay It means that the button lever of the lid is not long enough, and it is not in place every time you press it Just put the button lever longer (don't grow too much, or it won't cause water leakage).

There is also a way to increase the water level and water volume by increasing the water output to improve the flushing function, specifically to raise the floating bucket of the water inlet valve, and you can also adjust the full row adjustment knob of the drain valve to extend the discharge time of the drain valve to improve the water output

The above is my experience, you can try it, of course, there are also problems with the toilet itself, these problems can only be solved by the dealer

If you still don't understand, you can come to my **store: Xitao Tao sanitary ware collection.

My space also has an address.

When the water gushes out of the tank, the float floating on the surface of the tank will descend, pulling the float arm downward, thus raising the valve plunger of the float valve device.

The float valve rises as the water level in the tank rises until the float arm is high enough to press the valve plunger into the float valve and close the incoming water flow. If the water cannot be turned off, the excess water will flow down the water pipe into the bucket tank to prevent the water in the tank from overflowing.

Merchants should deal with it correctly as soon as possible, and it is not easy for customers to decorate their homes.

It may be a slow discharge caused by the connecting rod on the drain or the long pull chain

To repair a toilet, the following steps are required:

1.Check the toilet for leaks or blockages. If there is a water leak, you need to check the tank and water pipes for damage or looseness. If there is a blockage, it can be removed with a toilet bowl unclogger or chemical cleaner.

2.Check that the gasket at the bottom of the toilet bowl is in good condition. If the gasket is broken or aged, it needs to be replaced.

3.Check whether the parts in the toilet tank are working properly. If the parts inside the tank are damaged or obscure, they need to be replaced.

4.If there is a crack in the bottom of the toilet bowl or it is damaged, the entire toilet bowl needs to be replaced.

5.If the above methods do not solve the problem, it is recommended to contact a professional toilet repairer for repair.

Shower head leak repair method:1. When the shower head leaks, use the lashing belt pliers to unscrew the handle of the sprinkler head from the hose. If you use other wrenches, tie the hose with tape to prevent it from being scratched by Sun.

2. Wash the threads on the handle and apply plumber's adhesive or plumber's tape around the perimeter. 3. Turn the shower head back and tighten it by hand. Remove any excess adhesive and tape and repair leaks at the turning ball of the shower head.

Start by unscrewing the sprinkler head from the steering ball ring. Second, look for the O-ring inside (this ring prevents water from leaking out) or similar seal. Replace it and screw the nozzle back into place.

The reasons for the leakage of the shower head are: 1. Thermal expansion and contraction In the process of water heating, the shower head sometimes drips, but this situation will be reduced when the weather is cold and the water temperature is low, because when the temperature is high, the volume of water will become larger and overflow, and such a dripping situation is a normal phenomenon and does not need to be treated. 2. Impurities and sediments shower head has been used for a long time, and many impurities will be deposited in different parts of it.

Therefore, in this case, it is necessary to disassemble the shower head for cleaning, and if the parts are loose, they need to be carefully checked, and the loose parts should be tightened in time.