A hole in your pants? What to do if a sweatpants have a small hole?

If your pants have a hole, it's embarrassing, but if you're on the street, you can buy something to cover it up, such as a plastic bag, or buy something to put on your hand and use a plastic bag to cover your part.

Ah,It shouldn't matter much.,You can watch it if you want to.,Well.,It's not like you deliberately broke it.,Ha just watched it.,Then you've seen it.,It's useless if you're thinking about it in your heart.。

After a while, no one will remember that if the pants are torn, they will buy *** a little bit, and if it doesn't work, you can take it and make it up.

A hole in your pants? This is normal, because pants with holes are still very fashionable now, and the price of pants holes is still very high, because they are called beggar's pants and pants are still very face-saving when worn out.

If your shoes are torn, you have to change them to a good pair of shoes, do you have a pair of shoes at home?

As long as you don't feel embarrassed, no one will find you embarrassed. I think this sentence is very good to see, this kind of sophistication, there is no way, face it calmly.

Will be broken, and remodeled. The beggar's pants are also nice and cool.

As long as you're not embarrassed, it's someone else who is embarrassed. You just pretend you don't know.

See, I'm embarrassed at this time, what should I do in this situation.

Treat him as if he did not know it.

Step 1: The pants are torn, and if they are sewn directly on them, the stitches can be seen from the outside, which will be very unsightly. First, turn the inside of the pants outwards to leak out the broken copper; Simple stitching with a small needle (the front back should follow the texture of the pants when stitching).

After sewing, turn it over again, the effect is very good, and the stitches are not visible from the outside.

Step 2: Prepare an adhesive sticker. Aim the side of the glue at the hole and stick it firmly.

Step 3: Use the iron, heat it at high temperature, and iron it with the sticker. When the adhesive sticker fits perfectly into the pants, you can turn off the iron and wait until the pants are cool.

Tips: During the ironing interval, the iron should be placed vertically away from the clothes, or placed on the special iron rack, do not put it in the pile of clothes, and cover the iron when the clothes are moved, so as not to cause disasters.

Finally, the pants were turned over, and the hole was completely repaired.

Sweatpants have a small hole, and you can paste a decorative sticker on the small hole to make up for the hole.

Tools and materials to prepare: decorative stickers, cotton cloth, steam iron.

The specific steps are as follows:

1. First of all, choose a more suitable decorative sticker and put the decorative sticker on the hole in the sweatpants.

2. Place a layer of cotton cloth on top of the decorative sticker to facilitate the subsequent ironing.

3. After the steam iron is steamed, iron it back and forth on the top of the decorative sticker through the cotton cloth.

4. After about ten seconds, the decorative sticker is completely glued to the pants, and the previous hole is completely covered.

1. Prepare some fabrics, thick threads, needles suitable for thick threads, thimbles, and scissors.

2. Trim the position where the wind must not break the hole slightly.

3. Put the sewn fabric inside the hole in the jeans, and fix the fabric with a needle and thread as shown below.

4. Try to keep the spacing of needlework and thread consistent.

5. Repeat the operation of the third and fourth steps all the time, and sew the whole fabric at the position of the hole.

What to do if you accidentally break a hole in your pants? Throw it away? Don't lose, this guide shows you the remedy for a hole in your pants that is guaranteed to look better than your new pants.

01 If there is a hole in the jeans, as long as it is not in the position such as the buttocks, you can use the hole to make ripped jeans. Use a stiff brush to brush the hole several times to make it look natural.

02 If you don't like ripped pants, then buy a fabric sticker and stick it directly on the hole, as long as you choose well, this non-fabric sticker will make your pants very personalized.

03 If you are a skilled needle, you can use a needle and thread to sew up the holes in your pants, but remember to do it from the back side, otherwise it will be ugly.

04 I've done embroidery for a while, whether it's hand embroidery or computer embroidery, so the best way to have holes in my pants is to embroider them on them, and a pair of pants looks tall and tall.

Hello, I am happy to serve you and give you the following answers: the clothes that break the beam hole can be repaired by sewing, and the steps for concealing the slippery flushing and sewing are as follows: 1

Disassemble the clothes at the hole, pull out the thread at the hole, and cut it with scissors; 2.Flatten the clothes in the holes and sew them with a sewing machine, paying attention to the tightness of the stitches when sewing; 3.Flatten the sewn clothes and iron them with an iron to ensure the firmness of the sewing; 4.

Flatten the ironed clothes and wash them in the washing machine to ensure the softness of the clothes. Sewing clothes requires certain skills, and you need to be proficient in sewing skills, as well as ironing and washing skills, in order to ensure the sewing effect of clothes. In addition, when sewing clothes, it is necessary to pay attention to choosing the right sewing thread stove and choosing the right color to ensure the aesthetics of the clothes.