Looking for a computer whiz!! About FAST Wireless Routers! 20

If you don't have a problem setting it up, you're in for a cup... Routers are the most annoying thing operators have. One more router, they make less money, generally secretly used, some operators through technical means, can not use routers. You also call 10,000 to tell them that you use a router, and if they stare at you, you won't be able to use the router at all...

Check whether the password in the router has been entered incorrectly. Check whether DHCP is disabled. Check whether the wireless function of the router is turned on. Check whether the IP address of the computer is obtained automatically.

Basically, after checking the above, if you can't access the Internet on the wireless router, there are only 2 reasons: 1. There is a problem with the router, please ask the seller; 2,The router is disabled by the operator (this is a regional difference,Some places don't care,Some places allow you to use 2 computers,Some places are disabled),But you call 10000,It's telecom,Telecom should be allowed to use,So,It is estimated that you have a problem with the settings of the router。

You ask them if they lock the MAC address.

First, look at the routing manual to set up the route.

2. Find someone who sells the router to you, (bring your ADSL broadband account number and password) and ask him to set it up for you.

3. Take the router to the person who repairs the computer to help you set it up, (bring your ADSL broadband account number and password), or come to the door.

Just choose one of the three, good luck.

The router cannot be used because the telecom is bound, give 10000**, give you the untie, and then use the cat to directly connect to the router to log in. It can be used by several computers at the same time.

Strongly despise telecommunications binding.

How to use the fast150M mini wireless router:

The router is selected by AP mode:

Connection method] 1. Wireless routers --- miniature wireless routers.

2. DHCP of the wireless router needs to be turned on.

3. The wireless device can be connected to the wireless wifi of the mini wireless router to access the Internet.

Is the router plugged in the network cable and power supply?

Reboot the machine a bit.

Can the wireless network card driver be installed?

If it is used in a company, is there any restriction on the NMS?

Connecting, that is to tell you that the router is dialing, it does not mean that the connection has been successful!

It should be that you and the secret are not filled in correctly, the total dial cannot be dialed, and the dialing mode of the router should be normal mode.

Also, if you have a habit of blocking routes in your area, then clone the MAC address

It's better to grab a few pictures. Maybe your fast router doesn't have routing capabilities.

Hello, the light on the WAN is connected to the external network, that is, the line that comes in from the outside, if the light is not on, it means that the line is broken!

The second point is, what kind of network cable is your home? If it is a dynamic IP, it is easy to do, you can use it directly, static, you can enter your network segment of the Internet; The other is to enter the account number and password!

Hello! You need to log in to check the settings of FAST

1. DHCP service must be turned on, and the wifi connection of HD2 and other devices should not use static IP as much as possible, so as not to manually set unclear parameters and cause inability to connect to the Internet;

2. Enable SSID broadcasting, change the wireless frequency band (with 6 or 11), and cancel the wireless encryption. Then test if the wifi connection is able to surf the internet. If you can, reset the wireless encryption in the router;

3. If it still doesn't work, you reset the router and reset it, only set one WAN port parameter, don't set anything else, test the wifi connection use.

Hope it helps, good luck!

The router may not support WiFi, so get a new router or upgrade the router software.

Hello, route settingsYou can set it up by following the steps below!

1. Connect the home network cable to the WAN port of the router, 2. Connect your computer with another network cable at one end, and connect the LAN port of your router at the other end

interface! 3. Open the computer, open the browser, enter the route login IP in the address bar, 4, enter the route login account and password in the pop-up dialog box, friendly reminder, if you don't know the route login IP, login account and password.

code, you can turn the route over and look at it, and there is a writing on the back of the route!

5. After entering the routing setting interface, the quick setting interface will generally pop up, and you can select the broadband dialing method in this interface.

PPPoE, enter your Internet account and password!

6. After the settings are completed, save the exit and restart the route!

Once the routing restart is complete, your routing hardware connection and setup are complete!

In addition, there is another point to remind that if your home is a ** line and there is a cat, it is recommended that you turn off the power of the cat when you set the route, and when the route is set up, turn on the power of the cat!

Reset the router:

1.Change the local connection to automatically get an IP address.

2.When the wireless router is plugged in, do not connect the home network cable first, reset the wireless router (restore the factory), connect the computer to any "LAN" port of the wireless router, enter the setting page, and set it according to the PPPoE (ADSL virtual dialing) method. Then set the SSID, encryption method, and password.

Save, restart. After setting up, connect the home network cable to the "WAN" port of the wireless router.

Follow the above two steps and you try.

Enter it in the address bar of your browser.

Then set it up yourself, be cautious when it is factory, and find the tutorial yourself.

Isn't there a manual, follow the manual? Try it again.

**Cable--- cat --- network cable ---WAN port) wireless router (4 LAN ports) - computer.

Setup of the router:1The IP address of the computer is changed to be obtained automatically.

2.Type http:http:

The specific can be found below the router)3The default username and password for --- login are: admin4

After logging in--- --- in the upper left corner, select the Setup Wizard --- dynamic IP Note: The router is no longer connected to broadband after it is set up.

678 Fault Description: Unable to establish a connection.

This fault is complicated, and any link between the user and the BRAS link may cause a 678 fault, which should be handled accordingly according to different situations.

Please confirm that the wire port is connected, I set it up like this, for your reference, good luck! :

Oh, check the network parameters obtained when your company's network cable connects to the computer and can access the Internet normally, and then check the login IP address of your router, if it is in the same network segment, then connect your router and the computer, and modify your router LAN interface address to avoid the same network segment after logging in, for example, the IP address of your router LAN interface is, then you can modify it to solve it later.

Modify the LAN of your fast router first, do not be in the same network segment as the address of your company network, for example, your router LAN address is set.