What should I do if the exhaust fan hole in the bathroom is large?

This one is easy to solve.

It can be plugged directly with styrofoam.

Fix the exhaust fan and beat the styrofoam.

If the hole is too big.

It can be plugged with an insulating board and then smeared with cement.

In fact, in this case, you can find some professionals to re-get it for you, which is not a big deal, and if you get it, it will be a matter of one or two hundred yuan. If the exhaust fan hole is large, it will cause special discomfort.

The exhaust vent in the bathroom is relatively large, what should I do? Then find a way to block it, for example, when you hang the ceiling, use some materials to plug it so that it won't be very big, only find a way to do it.

The exhaust fan hole in the bathroom is left large, and there is no way to change it to a smaller one, so you can only buy a larger fan according to the size of the hole to install it.

Cut a tile and stick it to the exhaust vent, then make the eye of the fixing screw on the tile, and hollow out the tile in the middle so that the wine is OK.

This question depends on the situation. First of all, it depends on what kind of exhaust air your bathroom presses, if your bathroom is installed with a fixed exhaust wall, then you need to reserve a 29 cm cube.

That's it. If the bathroom has reserved exhaust ducts, it is 7 centimeters.

The exhaust fan hole is left large, in fact, it is very simple, just repair it with cement, and repair it as big as you want.

It should be handled like this:

This hole is usually on the top of the ceiling. You can punch holes in an ecological board and the current air duct is generally large, and you can nail the ecological board with a hole in the exhaust outlet, and the size of the ecological board will be determined by yourself.

If the hole of the exhaust fan in the bathroom is large, you can seal it later according to the size of the pipe, you can use the glue of the pipe sealing, and fill the excess air gap.

All you have to do is buy some filler cement to make up for it, and when it's dry, then install the socket.

The reserved hole can be filled if it is large, but it cannot be installed if it is small.

You can use cement to fill the cement slurry with the large reserved holes, and then you can install the switch and the skewer seat in the cement fixed bottom box, and the cement is fixed better than the wood, and it is not easy to loosen and extraordinary, you can try it.

You can buy the kind of socket with splash cover, which will be larger than the 86 socket and should be able to cover the reserved hole.

Replace it with a new one, or ask a professional how to deal with it.

The reserved hole of the toilet socket is larger, which can fill the gap on the 86 bottom box.

Get someone to fix it and replace it with a new outlet.

Just change it to a small one, it's just a little more troublesome.

If the opening of the bathroom socket is too large, you can buy that kind of decoration to cover it or use glass glue to fill the gap.

The panel guard is out of reach, it's too big, so I have to rework and repair the tiles, please master, there will be a way.

The exhaust duct is flexible, and after the reducing, it can pass through the hole. I hope my answer can help you.

1. If buried, the filling should be filled with hemp or expanded (asbestos) cement;

2. If it is exposed (suspended), the filling should be filled with waterproof cement (more expensive), waterproof construction ointment or foaming agent; Cover the outside with a cover plate;

It's not safe to do this.,Use 160,Change diameter 110.。。。

The one with a check valve is square on one side and round on the other, right?

The mandatory provisions of the engineering construction standards of the People's Republic of China stipulate that the dark guard of the residential bathroom must be equipped with an exhaust duct.

In the standard requirements of residential toilets, there need to be "bathtubs, showers, washbasins, toilets, mirror boxes, washing machines, exhaust ducts, mechanical exhaust devices, etc., in order to reduce the interference of use, it is divided into several functional partitions of defecation, bathing and laundry.

The facilities in the bathroom are required to integrate urinals and baths; The feces are discharged by the closed pipes, and there are special handwashing stations, washbasins, showers or bathtubs, lockers, washing machines, exhaust vents and other facilities; Pay attention to the indoor dry and wet partitions, the smoothness of the drainage system in the toilet and the installation of ventilation equipment; In the appliance, the quality and waterproof of vulnerable instruments are required, and new materials are gradually reflected in the application of toilet appliances; In order to reduce the area occupied by the rear water tank, it is not uncommon to use a built-in wall type in the design.

The volume of mm is just right, but the natural convection effect is definitely not good.

mm or 200mm or square ventilation ducts should be fine, but they take up too much space and are not aesthetically pleasing.

3. It is recommended to use a 110mm pipe, and then install a larger ventilation fan to connect with the ventilation pipe, and the sealing at the interface should be done.

4. The ventilation pipe should also be blocked and waterproofed at the floor surface, otherwise it will rain and leak. The size of the toilet exhaust duct is generally 15 cm and 18 cm in diameter, but now the popular ones in the market are 15 cm. The exhaust volume of the range hood is generally 300 500 cubic meters per hour, and the effective air inlet cross-sectional area is not less than, which is equivalent to the air inlet wind speed of 4 7m per second.

The exhaust volume of the toilet exhaust fan is generally 80 100 cubic meters per hour, although the wind pressure is small, but the effective air inlet area is not less than, and it can also meet the requirements.

Another remedy is to use mosaics (small pieces), carve the holes into squares, and paste the mosaics. This can do something unexpected and have a different flavor. Paired with your bathroom cabinets should work better.

Hejia bathroom professional bathroom cabinet manufacturer.

Hello! If the decorative cover in the faucet still can't be covered, then try to find something to cover it yourself, I made my own disc, which is the smallest disc, which is much better than having a hole in the wall, try it.

The easiest way is to buy a faucet when you pick a large decorative cover that can cover the hole, if not, as the brother said above, use white cement or other materials to remedy!

Plug it with white cement and install the pipe decorations.

Go to the shop that sells faucets in the renovation market and buy a stainless steel faucet wall plug cover and install it.