How to debug the computer old from floppy boot

Updated on number 2024-05-04
4 answers
  1. Anonymous users2024-02-09

    Press F2 or Del to CMOS during boot, and select the boot device order to hard disk

  2. Anonymous users2024-02-08

    BIOS settings disc on.

    biossata：……

    cd/***：……

    1st floppy drive

    disabled

    How to set the U disk on.

  3. Anonymous users2024-02-07

    Press F2 or Del to CMOS during boot, and select the boot device order to the hard disk.

    harddisk

  4. Anonymous users2024-02-06

    Floppy Disk(S) fail, floppy disk failure, after turning on the computer or restarting the computer, press the "del" key in time to enter the BIOS settings interface, click a few options casually, but don't modify, stay in the BIOS environment for about a minute, the BIOS will automatically help you set up, press the ESC key, F10 key, Y key, press enter to store and exit the settings.

    How about trying it out? Do not pick up the line, and then use the following methods:

    1. Restore or optimize BIOS settings.

    After turning on the computer or restarting the computer, press the "DEL" key to enter the BIOS settings interface during Xunsou, and awardload BIOS defaults, this option is used to load the initial BIOS settings to determine the fault range.

    Load Oprimum Settings, which are optimized settings for the factory BIOS.

    or AMLLOAD BIOS Setup Defaults, which is used to load the BIOS initial settings.

    Load High Performance Defaults, which is used to load the BIOS settings.

    After selecting the default or optimized value with the keyboard arrow keys, press Esc, F10, Y, press Enter, Save and exit the setting.

    2. Turn off the floppy drive.

    Reboot, press del into the BIOS, find the standard CMOS setup, press enter in the open interface, change drive A: and driveb: to none, set Floopy 3 (floppy drive) to disable, press ESC, F10, Y, press enter to save and exit the settings.

    3. The floppy drive is not detected when it is turned on.

    Reboot, press Del into the BIOS, find the Advanced BIOS Setup, press Enter in the open interface, set "Boot Up Floppy Seek", set to "Disabled", press ESC, F10, Y, press Enter to save and exit the settings.

    4. Set the hard disk as the first boot. Reboot, press del to enter the BIOS, find the Advanced BIOS Features (advanced BIOS parameter settings) press enter to enter the Advanced BIOS Features interface, set the First Boot Device to HDD-O (hard disk boot), press the ESC key, F10 key, Y key, press Enter to save and exit the settings.

    5. Check and replace the motherboard battery.

Related questions
How to set up the computer to boot from the hard disk?
6 answers2024-05-04

The boot order needs to be adjusted in the BIOS.

The boot page must pay attention to the English of the page, at this time you need to remember to enter the keyboard button of the BIOS settings, different computers have different BIOS settings, be sure not to press randomly, according to the boot page to determine, for example, this computer is to press F2 >>>More

The computer boots up sometimes abnormally, what is the reason why the computer cannot boot normally
8 answers2024-05-04

It's a problem with the hard drive, and the hard drive has a logical error. >>>More

My computer is booted from a CD-ROM drive, how can I set it to boot from a hard drive?
3 answers2024-05-04

Set up hard disk boot:

The so-called hard disk boot means that the computer reads the hard disk first when it boots up. >>>More

How to tune the guzheng from G to D?
10 answers2024-05-04

Move the yards of each do a little to the left.

How to adjust the speed of the computer sound, and how to adjust the sound of the computer to sound
5 answers2024-05-04

If you want to change all the sound of the system, you can adjust it in the console of the sound card, this depends on what sound card you use, if it is AC97, you can go to the latest driver of the driving house**, there is a sound adjustment function in it. >>>More