-
There is a problem with the built-in flish in the browser, please use the computer clinic in 360 Security Guard to fix it.
-
Update the flash plugin and try it.
-
Analyze your situation, you should have two computers connected on the same route.
The cable should have been connected by you yourself (i.e. in a service such as telecom or Netcom), and if this is the case, then you should not have set up a route. One computer can dial numbers, while the other computer can't, and there is a conflict when you dial up. This computer cannot connect to the Internet because the router does not have an IP assigned to it, so this computer cannot receive signals.
Naturally, there will be no network.
To enter the account number and password of the route into the route, you can set it to autocast!
How to set up: 1. Connect the settings (if you don't know this, I can't help it!) )
2. Open the webpage and enter a dialog box where you will be asked to fill in your account and password. The account number and password are on the back of the route, fill it in and you can log in!
3Click on the "Broadband Settings", and there is a place to fill in the account number and password on this interface.
4. Fill in the account number and password of your network cable. Save and set the auto-dial to reset the route. (You only need a computer to set up the route!) )
5. Set the IP in your computer, click "Internet Neighbor", "Local Connection", Properties, and IP Protocol. Both computers need to be set, just fill in the numbers in between in the IP! (Do not set the same IP for two computers).
This way, both computers will be able to access the Internet. The above method is the setup method of telecommunications. Other network cable services have other IP addresses, you can see it, just change the number!
If you don't have your own network cable, (such as the school one), then it should be your network cable problem! or the interface of the route. The solution is basically to change the equipment, because you don't have the tools.
-
Is it plugged in the wrong line?,I just ran into this problem and check the plug-in from the new.,Or it's the computer's network card that has a problem There is also an IP address setting.,For example, if there is a network, the address is set to you or 4.,And then turn on the routing mode in the router.,You can have a network.。
-
Enter the router and configure the HDCP address pool and DNS
-
If your mobile phone cannot access the Internet normally, please check the following conditions:
1. If you don't restart your phone after upgrading to 4G**, you won't be able to use the Internet function normally;
2. Confirm whether there is a network, it is recommended that you can use it in a place with a strong signal;
3. Check whether there is still a phone bill in the account, if the balance is insufficient, you need to recharge before you can use it;
4. After 3-5 minutes of power off, restart the phone and try again;
5. Check whether the USIM card is inserted, if it has been inserted but still cannot be used, it is recommended that you go to the business hall to check whether the USIM card is faulty, or replace the card for testing;
6. If the traffic usage reaches the maximum value in the current month, the network will be automatically closed, it is recommended that you pay attention to our SMS reminder or inquire about the **product description.
-
It may be that the router has set a limit.
-
In the device management, uninstall the network card driver of computer B, and then search, automatically install the network card driver from the device, restart the computer, and then change to the IP of computer A, DNS, or automatically obtain, try it?
-
Well, I've also encountered it, it's my A computer that can dial up, and the B computer can't dial the number by copying the IP, and finally directly dialing the telecom 10000 to let him refresh it directly.
-
If you want to use a router to connect, you should set the DNS of computer B to automatic!
-
You can try it by setting the IP address automatically
You said) This traffic problem has nothing to do with the internet speed problem. This is not only you alone, but many friends have encountered it. >>>More
First determine if it's caused by a network failure, if not, take a look at the methods below. >>>More
Possibly. But it's also possible that you have too much stuff on your computer.
1. The antivirus software is installed more, and all the monitoring is turned on, less monitoring is turned on or not monitored, and the virus is often checked and killed. >>>More
Reasons for slow opening of web pages: 1Broadband connection, unstable network speed, if you are in a LAN environment, most people are using broadband resources such as: >>>More