The brother who knows a lot about recorders can help, please 100

Updated on number 2024-05-10
7 answers
  1. Anonymous users2024-02-10

    I think BenQ is the best fit for your requirements.

  2. Anonymous users2024-02-09

    BenQ's is not good for Samsung and Asus, and Pioneer is also a little more expensive

  3. Anonymous users2024-02-08

    Fortunately, the pioneer is a little more expensive.

    Jianxing has two machines, which I personally feel very good.

    Lite Hing LH-18A1H

    Lite Hing LH-18A1P

  4. Anonymous users2024-02-07

    Now many *** recorders are in 3xx, depending on what you bought to do, if you use it yourself, there is no need to buy a burning speed that is very fast, waste. Because high-speed disks are also more expensive, I used to pursue indicators in this way, and the results were also in this way. I can't afford to use a 16x disk--- if you use it a lot.

  5. Anonymous users2024-02-06

    BenQ DW1640 390

    Type of optical drive *** burner.

    Installation: Built-in.

    Interface type: ATAPI EIDE

    Burner Specifications ***+ -rw

    The maximum CD reading speed is 40 speeds.

    Max*** read speed 16 speeds.

    The maximum CD burning speed is 40 speeds.

    The maximum *** burning speed is 16 *** R, 8 ***+r DL speed, and the maximum CD copy speed is 24 speeds.

    Max*** rewrite speed 4 speeds.

    The buffer area has a capacity of 2MB

    Supported platter standards ***+R DL ,***+r , ***+rw , ***-r session), ***-rw (closed session) *** video, ***-5, ***-9, ***-10, ***-18,cd-da, cd-rom xa (m1, m2f1 m2f2), cd-r, cd-rw, bootable cd, photo cd (single and multi-session), video cd, etc.

  6. Anonymous users2024-02-05

    For *** burners, every 1x speed (1x) is 1350 kb s.

    then 5644 kbs is equivalent to a little more than 4x.

    However, it is important to note that the actual burning speed depends on the disc, hard disk, and burning method. If the maximum allowed speed of the disc is lower than the burner's speed, the burner automatically slows down to accommodate the burner. If the speed of the local hard disk is slow (aging, other work in the background, etc.), it will also automatically reduce the speed to prevent data interruption and damage to the disk.

    If you use ***-rw rewritable burning disk, and use the method of erasing old data while writing new data, the best ***-rw disk can only reach 4x speed.

    In addition, because the linear speed of the disc is different everywhere when the disc rotates, the linear speed of the inner ring is slower than that of the outer ring, so it is possible to reach the maximum speed when burning the outer side of the disc, and the inner side will be slower, so the average speed is pulled down.

  7. Anonymous users2024-02-04

    p picture, see the host configuration or a screenshot of nero at that time.

Related questions
4 answers2024-05-10

The speed of burning is determined by the slowest of the burners and burning discs. >>>More

8 answers2024-05-10

Haha..I'm here to join in ..the fun, tooThe recommendations are as follows: >>>More

7 answers2024-05-10

Take a look at the format, and then look at your burner's instructions to see if it's supported. >>>More

3 answers2024-05-10

CD-R disc is made of polycarbonate with a layer of dye sprayed on the base, and the laser head controls the power of the emitted laser beam according to the different engraved data under the control of software and hardware, so that part of the dye is decomposed by heat, and the reflective point that can be read is "burned" at high temperature on the blank general sheet. Because the dye layer cannot be restored after decomposition. >>>More