Why is the letter incoherent on the two point axis mark of Tianzheng 7?

Updated on society 2024-05-14
12 answers
  1. Anonymous users2024-02-10

    The cartographic specification stipulates that the i, o, and z of the Latin alphabet shall not be used as axis numbers. The axis number of Tianzheng also does not use these three letters.

    If the missing is other letters, it is because the sky is recognized as a double-sided shaft mark, that is, it automatically identifies the axis number on both sides of the axis, the axis only extends out on one side, and the axis number on the other side is hidden and not displayed, if the axis is only drawn in the middle, does not highlight both sides, and is hidden on both sides, you look like the missing number. In addition, if there are heavy lines on the axis, it will also cause numbering errors. Change the axis line you don't have to number to a different layer, and you won't make a mistake with automatic axis numbering.

    Manual change of the shaft number is supported by TENGEN software, and you can change it by double-clicking the number of the shaft number. Double-click on the outer ring or leader of the shaft number, and you will see the hidden number, and there will be a command prompt.

    Variable Dimension Side (m) Single-axis Variable Dimension Side (S) Supplement Axis Number (a) Delete Axis Number (D) Uniaxial Variable Number (n) Rearrange Axis Number (R) Diameter of the Shaft Ring (Z)] "Exit":"

  2. Anonymous users2024-02-09

    Types of Questions:1If there is a duplicate axis line, the axis number is marked twice.

    2.The axis number is on the opposite side, 3In the axis number, i, o, z, are easily considered to be , so they are not used. This is a requirement of the architectural drawing standard, and you are doing it wrong if you change it.

  3. Anonymous users2024-02-08

    Have you ever tried to manually enter the shaft number, right?

  4. Anonymous users2024-02-07

    Landlord, when you click on the two-point axis, you have the tick that shows the axis number and size.

  5. Anonymous users2024-02-06

    In the annotation there is no point start axis number, the level is displayed with the axis number.

  6. Anonymous users2024-02-05

    Maybe the layer is turned off by you, and the font is generally not lost out of thin air.

  7. Anonymous users2024-02-04

    Pull a straight line to the position you want him to be, then select the axis and hold down the blue dots that appear to pull them one by one to the reference line, there is no better way to do this.

  8. Anonymous users2024-02-03

    Click on the axis line, the blue dot will appear, and pull the blue dot below the axis line up to your desired length.

  9. Anonymous users2024-02-02

    Right-click on the object and then enter the value of the radius of the shaft coil Small dots are good

  10. Anonymous users2024-02-01

    In this case, you can try to put the layer under the dote layer, and if it's a hand-animated axis, the pl drawn can't produce the axis number, and I'm used to drawing the line with pl, so I found out this problem.

  11. Anonymous users2024-01-31

    Would you like to try another Tensho option?It may be that you did not activate the annotation command to change it yourself, so that it is convenient to annotate and measure the distance in the drawing!Also, when drawing, try to use the grip method to modify or be.

  12. Anonymous users2024-01-30

    That's the same question for me. Have you solved it ?

Related questions
There are two points A and B on the plane, and the two points A B in the plane are symmetrical
12 answers2024-05-14

Any position on the line segment connected by point A and point B is eligible, that is, when the point C is on the ** section AB, the sum of the distances from point C to point A point B is 7 cm. Because the line segment between two points is the shortest, the distance between the two points A and B refers to the length of the line segment AB, and the sum of the distances from point C to A and B is also 7 cm, so it can only be on the ** segment AB. >>>More

Born at about two o'clock in the morning on July 26 of the 84 lunar calendar, female, please count y
5 answers2024-05-14

Summary. Today's eight-character numerology information:

Gregorian calendar date: Monday, February 26, 1979. >>>More

Two o'clock in the morning Korean lyrics, two and a half in the morning, lyrics
11 answers2024-05-14

Two o'clock in the morning one-man coffee shop.

I miss the restless emotions that I once had. >>>More

I often go to bed at two o'clock at night, but I don't get up until nine o'clock in the morning, is
36 answers2024-05-14

Yes, you have already stayed up late, normal people have to sleep for at least eight hours, and your work and rest time is already irregular, which will have a certain impact on the body.

Two questions about the death of Western metaphysics
19 answers2024-05-14

1. First of all, the first question is that the death of Western metaphysics has a certain connection with the assumption of the reality and nature of the atom, but it is only for background reasons. The real reason lies in the fact that since the European Enlightenment in the Sixteenth World, the development of science, marked by reason, began to impinge on the speculative basis of traditional metaphysics. In particular, the empiricism is represented by the emphasis on experience as the original point of knowledge, and the metaphysical metaphysics is abandoned. >>>More