What to do with computer speaker distortion, what happens to speaker distortion??

First try to replace the microphone,If the speaker is still distorted,It means that it has nothing to do with the microphone,The problem should be in the hardware or software settings of the sound card。 Of course, the quality of the microphone should be about the same, and it is best to use a condenser microphone, such as some conference (gooseneck) microphones at a reasonable price. The microphone on ordinary headphones is prone to "microphone spraying" and causing distortion.

Secondly, we need to understand the connection between the electric guitar, microphone, and speaker and the computer.

There are three sockets in the back of the computer: red, green and blue, generally the green socket (audioout) is output to the speaker, and the red jack (mic

in) is the microphone input, and the blue jack (line

in) is the line input.

Therefore, the connection method is:

The speaker --- green jack, the red jack --- the microphone, and the blue jack --- electric guitar.

Don't misplace the microphone and electric guitar.

Press the above position to connect, and you can record normally.

If the speaker is distorted, the signal input is overloaded, please reduce the input volume. You can lower the size of the line input in the volume control, or turn down the output volume of the electric guitar a little bit, try not to distort, and the sound is not afraid to be smaller, we can make the sound louder later. If it is distorted during recording, then it is very difficult to do post-production.

In addition, you can use a mixer, input both the electric guitar and the microphone into the mixer, and the mixer outputs to the computer, the mixer has a high signal-to-noise ratio, which is better than directly entering the computer. That will be easier to debug, and the level meter on the mixer is very intuitive to see the size of the input and output signals, high, medium and low bass can be arbitrary, as long as you like.

It should be your sound card driver is not right.,It's good to find your on-board driver to install it.,Although some drivers can be played, the effect will be very poor.,There's also a place to set up.。

The speaker will not be distorted, the sound distortion is the speaker distortion, the reason for the speaker distortion is because of the magnetic field structure of the speaker, everyone knows that the speaker works by the magnetic field force, from the structural point of view, the magnetic sound structure of the speaker is shown in the figure!

The width of the middle figure represents the strength of the magnetic field, the force of the voice coil is proportional to the magnetic field strength of the stamen, the voice coil moves up and down, the position is different, the force obtained by the voice coil is also different, the longer the voice coil stroke, the greater the force difference, this is where the various distortions of the speaker lie, I have studied the magnetic field countermeasure method and solved all the problems.

If the audio circuit is defective, the audio will not work properly, such as electronic components heating, breakdown, short circuit, smoke, running water, etc., resulting in serious distortion of audio amplification, hoarseness, blockage, sound breakage and other phenomena. The main reason for the sound of an audio is that the circuit diagram design should be reasonable and the component installation should be standardized, otherwise it will not work normally and the sound will be distorted. In the existing circuit of the special integrated block for audio, the design of TDA2030A is very good, and the advantages are that the output power of the disturbance is large, the distortion is small, and the sound quality is good, and it is widely used in many well-known low-power audio.

The circuit diagram is as follows:

The speaker will not be distorted, the sound distortion is the speaker distortion, the reason for the speaker distortion is caused by the magnetic field structure of the speaker, everyone knows that the speaker works by the magnetic field force, from the structural point of view, the magnetic sound structure of the speaker is shown in the figure!

The width of the middle figure represents the strength of the magnetic field, the force of the voice coil is proportional to the magnetic field strength of the stamen, the voice coil moves up and down to grind the draft, the position is different, the force obtained by the voice coil is also different, the longer the voice coil stroke, the greater the force difference, this is where the various distortions of the speaker lie, I studied the magnetic field countermeasure method, and solved all the problems quickly.