What if the geothermal heat is not hot? What to do if the geothermal heat is not hot

1. Carefully check whether the water in all the pipelines of your house is circulating, if there is stagnant water in the pipes of your house, no matter how hot the water outside is, your house is still cold.

2. If there is water in and water out, (that is, there is no problem with circulation), then you can see which section is not hot, where is the problem, and you have to eliminate it one by one to find the problem.

3. If it is not circulated, let it circulate, and if there is a problem with the pipe, heat dissipation equipment, and switch, replace the faulty place.

Some people are that the geothermal heat at home is too hot, that is, the geothermal switch is fully turned on) your geothermal heat is not hot, most of the time the circulation is not smooth, and the flow is small).

You can find the property company first, if not, then find a professional and technical personnel to see, there may be insufficient gas, there may be insufficient water... Hope you can find a solution.

Let's see if it's blocked. Maybe it's a filter.

Causes and solutions for general floor heating not to heat:

1. There is air in the geothermal pipe, which hinders the water circulation, and the general water separator will have an exhaust valve, which is used to exhaust, and the newly used and installed geothermal must be exhausted. The method is: for example, if your home is a six-way water separator, first turn off the five-way (you can only operate all the way), open the return water exhaust valve, and discharge one of the water until only the water is out and the air is not out, and so on.

Second, the water temperature is low, if the indoor temperature should reach 19 23 degrees Celsius, the temperature of the floor heating water supply must reach more than 46, you can measure the temperature of the water inlet pipeline by yourself, and if it is not up to standard, you can contact the property of the respective community.

Third, the system circulation is poor, the pressure difference between the supply and return of the heating company is small, and the water flow rate decreases, resulting in the geothermal heat is not hot, which should also be solved by the property, otherwise it is really necessary to press a circulating pump.

Geothermal non-heat solution: 1. Clean the filter screen: The geothermal filter screen is blocked by silt and rust, which will cause it to be not hot, and the filter screen should be cleaned before heating.

2. If there is gas in the pipeline, the geothermal heat is not hot, and the gas in the pipeline is opened with the gas release valve on the water separator, and the gas is released until the hot water is released. 3. Install a circulating pump: the floor heating is not hot, and a circulating pump can also be installed, which can increase the floor heating temperature.

4. Reduce floor heating coverings: reduce floor coverings, such as carpets and furniture, should be placed less to allow the heat to be fully dissipated.

There are four main reasons why geothermal heat is not hot, among them, the most common reason is that it is not cleaned and maintained in time. According to the data, the average annual scale of geothermal pipe is 1mm, and the 1mm thick scale can lead to a drop in water temperature6, if not cleaned for a long time, the scale will be attached to the inner wall of the floor heating pipe for a long time, so that the temperature of geothermal heating is reduced, which is also the fundamental reason why people feel that the geothermal effect is not as good as a year.

Precautions for the use of floor heating: 1. Inspection and maintenance. Before using the floor heating, you need to carefully check the equipment to see if the pipes and accessories are damaged, and also to see whether the pressure gauge is normal, and clean the filter screen in advance.

Moreover, when the floor heating is in use, it needs to be cleaned regularly to maintain high efficiency, and you can ask a professional floor heating company to clean and maintain the floor heating pipes.

2. Slowly heat up. When using underfloor heating for the first time, special attention should be paid to the fact that the underfloor heating should be heated slowly, otherwise too much heating will not only increase power consumption, but also cause damage to the floor. 3. The temperature should not be too high.

When using floor heating, it should be noted that the floor heating temperature generally cannot exceed 30, and the temperature is too high to affect the normal use of the floor. The underfloor heating temperature can be adjusted at 22°C, which will make people feel comfortable and will not affect the use of the floor.

1. First check whether the flow adjustment of the water separator has been opened, and use the small valve on the water separator to mediate the circulation of each circuit, so that the whole house can circulate evenly to strengthen the heating effect.

2. Check whether the pressure of the pipeline is enough, if the pressure of the pipeline is not enough to cause the heating is not ideal, you need to find a heating company to solve it.

3. Check whether there is gas in the pipeline, because the gas in the pipeline will cause the hot water to not circulate, so you need to release the gas in the pipeline until the hot water is released.

4. Check whether the filter is blocked, open the geothermal filter with a bright pie wrench, and clean up the impurities inside, and the heating effect of the geothermal heat will become stronger.

At present, in the newly developed community, a geothermal system will be installed in almost every home, mainly to help residents better survive the harsh winter. So how to solve the problem of geothermal heat is not hot, and how to maintain geothermal heat in daily life, do you understand? Now let's take a look.

1. How to solve the problem that geothermal heat is not hot.

1. If the geothermal heat is not hot due to insufficient pipeline pressure, you can contact the property or floor heating company to solve it; 2. Because there is air in the pipeline, the geothermal heat is not hot, and the air opening valve needs to be opened to discharge the gas; 3. Due to the uneven geothermal circuit, it needs to be adjusted through the small valve of the water separator; 4. If the filter is blocked, you need to open the filter with a wrench and clean the filter.

Second, how to maintain geothermal energy in daily life.

1. When the indoor temperature is relatively low, it is necessary to turn on the geothermal heat to heat up the room, but at this time, it must go through a transition temperature to achieve the effect of slowly increasing the temperature, better protect the various components of the floor heating system from being damaged, and prolong the service life of the geothermal heat.

2. If you are not going to use geothermal heat in winter, then you need to protect the manifold to avoid damage to the manifold due to the decrease in temperature. It is important to know that when the temperature drops to a certain level, the water inside the manifold will freeze, which will cause blockage, so be sure to let the water inside flow out.

3. In daily life, if you need to use geothermal energy, you need to disconnect the switch, and pay attention to regular cleaning to ensure that there will be no accumulation of dust and impurities around the geothermal switch, so as not to cause blockage, it is not easy to clean, and it will become very troublesome when you need to use it in the later stage, and it is not conducive to long-term storage.

How to solve the problem of geothermal heat and how to maintain geothermal heat in daily life, I will introduce it here, do you understand? If the geothermal heat is not hot, it is necessary to find the relevant staff to test it in time and change it according to the cause so as not to affect the daily use.

The reasons why geothermal heat is not hot are as follows:

1. The pipeline pressure is not enough. Some households have too high floors or the heating of the community is not enough, and the pipe pressure is not enough, resulting in unsatisfactory heating. If the heat source circulation power of the floor heating is insufficient, it may lead to the return water of the floor heating is not hot, because the water needs a certain pressure to circulate in the floor heating pipeline, and if the pressure is not enough, the return water will not be hot.

In this case, it is necessary to find a heating company or find a property to solve the problem, if it cannot be solved, it is recommended to install a circulating pump to improve the circulation of hot water to achieve the ideal heating effect.

2. There is gas in the pipeline. The main floor heating bar is hot, and the return bar is not hot, because there is air in the pipe, which causes the hot water to not enter the circuit and cannot be circulated. Close the return valve first, then manually open the exhaust valve of the floor heating for exhaust, close each valve on the inlet water first, and then open the exhaust all the way.

There may be water overflow during the exhaust process, you can find a small basin to connect the water, wait for the air in the floor heating pipeline to be completely drained and heated for half an hour to see the effect, many times the return pipe is not hot is also related to the exhaust.

3. The circuit is uneven. Other users in the same community have good heating effects, but their own effects are not good, and the floor heating construction circuit is uneven. The small valve on the floor heating water separator mediates the circulation of each circuit, so that it can circulate evenly and achieve the ideal heating effect.

4. The valve is not opened. There is hot water in the floor heating inlet pipe, and the water inlet pipe is also hot, but the return pipe is not hot, this situation is likely to be caused by the main valve not being opened, it is recommended to check the main valve on the floor heating main and the manifold in turn to see if there is a valve in the closed state, if there is one, open it to solve the problem that the floor heating return pipe is not hot.

5. The water is not released at the end of the heating period. At the end of the annual heating period, the underfloor heating user should discharge all the boiler pipe water in the geothermal network.

In winter, it's time to heat up with geothermal heat, but geothermal is not hot, it's annoying, there are many reasons why geothermal is not hot, if you understand the reasons, it is easy to solve, so what if geothermal is not hot? Let me show you how to solve geothermal problems. 

1.There is gas in the pipe.

If the geothermal heat is only hot on the main bar and the return bar is not hot, it is because there is gas in the pipeline, and if there is gas in the pipeline, it will hinder the circulation of hot water, resulting in the geothermal heat cannot be heated normally.

Solution: The general geothermal water separator has an exhaust valve, which can drain the gas, open the waiver valve, and give up until the hot water is released.

2.Geothermal heat has not been used for a long time.

Geothermal energy is only used in winter, so the water temperature may not be high when the geothermal heat is first used, so the temperature will be very slow, and it is more obvious in some areas with lower temperatures, and it is very likely that it has not been heated to the ideal temperature for more than ten hours, which is easy to be considered a geothermal problem.

Solution: The geothermal heat that has not been used for a long time does not heat up is not the cause of the geothermal heat itself, and it is good to wait patiently for the temperature to rise in the first few times.

3.The filter is clogged.

Filter blockage is also a reason why the geothermal heat is not hot, the filter is used to filter impurities in the water, and after a long time, the filter will be blocked, which leads to a decrease in the water flow rate, and the geothermal heat is difficult to heat up.

Solution: Use a wrench to open the filter, clean the inner filter, clean and install it.

4.The pressure in the pipes is not enough.

Some owners have too high floors, but in some places the pressure in the pipes is not enough, and the speed of hot water flowing in the pipes will also be reduced, resulting in insufficient hot water in the pipes, and the natural geothermal heat is not hot.

Solution: Find a heating company and property to solve, if it can't be solved, you can install a circulating pump to increase the speed of hot water circulation, so as to improve the heating effect.