Desperate for ways and tricks to decorate car decals

A car that does not have a decal is not necessarily a high-end car, but a car that has a decal must be a low-end car.

The vicinity of the 4S store is best on the car street.

Wash and dry your car, and then stick it however you like.

I firmly believe that many young people's car friends are based on the body sticker on the latte pattern case to highlight the personalization, so how to paste the latte art of the car? Will the body latte art endanger the annual inspection?

Because the body latte has a high demand for lamination, it is recommended that car enthusiasts go to a professional car beauty salon to carry out practical operations as much as possible when the latte art with a total area is too large.

Let's give us a brief introduction to the pasting and dispersing process of automobile latte art:

Cleaning: Clean the car body neatly, especially the parts that are latched.

Sprinkling: Sprinkle water on the fit area after cleaning.

Lamination: Tear off the bottom paper of the latte art, and evenly spread the latte on the body, and finally carefully scrape the bubbles in the latte art according to the scraper (the actual operation of the latte art is as soft and slow as possible, otherwise it is likely to cause the deformation of the latte art).

Tear off the film: After all the scraping is smooth and symmetrical, the protective film on the surface of the latte is torn off, and the latte lamination work can be carried out.

Will the body latte art harm the annual inspection?

The state's management methods for car latte art are as follows, if the paper sticker of the body does not meet the above requirements, it is not possible to pass the Spring Festival trial, and at the same time, if you walk on the road to Chongyu and are seen by the police uncle, you may also encounter a penalty of 500-1000 yuan.

1.Because the bright red color of the special type for fire safety, the light yellow of the special type for emergency repair of virtual bridges in engineering projects, and the blue color on the top and bottom of the national comprehensive law enforcement special type all belong to the special color of special vehicles, therefore, we generally cannot apply the car.

2.Car painting, pasted logos or body advertisements shall not affect driving safety.

3.The total area of the car paper sticker shall not be higher than 30%, if it exceeds 30%, it shall apply to the transportation department for filing.

Millions of car purchase subsidies.

1. Use a razor blade to scratch the sticker Use a razor blade to lightly mark the label. Don't press too the shaver, just lightly swipe the sticker so you don't scratch the windows.

2. Add essential oils and use your fingers to process the orange essential oil into the engraved lines on the stickers. Orange essential oil will help loosen the sticker from the car window.

3. Remove the sticker from the strip If the sticker is difficult to remove, add more orange oil to the edges and apply it to the sticker with your fingers. After a minute or two, the sticker should start pulling away from the window.

4. Once the sticker is removed, wipe it clean. Now you can add a new sticker or keep your window clean and stickers!

Paste the whole car latte art steps:

1. Starting from the front cover of the engine, the paste area of the engine cover is large and the arc is large, which is the most difficult to operate, so it is very important to clean, and the fine dust particles should be wiped clean, so that there are no bubbles after the paste. Of course, the rag should also be clean, and if necessary, wipe it with dish soap.

2. After scrubbing, position the sprayed car sticker material on the front cover.

3. Tear off one foot of the film, and stretch it to the other side little by little after pasting.

4. It doesn't matter if there are wrinkles at the beginning, as long as it is not a broken material, you must be very patient at this time, slowly catch up, scrape slowly, and drive the water out of the picture, and be careful when pulling, don't use too much force to prevent the picture from being deformed.

5. When the water is almost dry, slowly use a hair dryer to heat the wind while blowing and gently scrape to flatten the folds, which is quite time-consuming and energy-consuming, and this step is quite critical.

6. Drop a few drops of 502 glue on some easy-to-provoke corners to increase firmness, so as to avoid the phenomenon of flashing and curling.

7. In the same step, the side body and the back of the latte art are pasted, and the material used is self-adhesive.

After scrubbing, position the sprayed patch material on the front cover. The so-called difficult beginning, the beginning is very important, the beginning is smooth, it is better to take the past, if the beginning is not good, there are wrinkles, bubbles, the more difficult to paste. There are two methods of sticking stickers and dry stickers, the area is large, and the arc is usually wet, that is, first spray the foam water (dish soap) with a watering can, all wet to paste, it doesn't matter if the picture has wrinkles at the beginning, as long as it is not a broken material, at this time you should be very patient, slowly rush, slowly scrape, drive the water out of the picture, and be careful when pulling, do not use too much force, to prevent the picture from deforming.

Three tricks to remove car decals:

Hair dryer air heating method.

Use a hair dryer to evenly blow the position of the sticker and let it fully heat, this process ensures that the hot air of the hair dryer is always blowing on the surface of the sticker. Therefore, the ideal form of operation is to start from the upper left of the car sticker, hold the hair dryer in the right hand, evenly blow the position that is about to be uncovered, and slowly lift the car sticker with the left hand. For left-handed comrades, it is possible to do the opposite, using the most skilled left hand to control the hair dryer.

Kerosene method you first use kerosene to apply to the sticker you want to tear, you must remember not to tear the sticker by hand, and then please wait for 5-10 minutes, a few minutes later, when you tear it again, it will come down, and there will be no shredded paper left.

Chemical agents.

Using chemicals, such as adhesive removers, is a simple and convenient way to directly treat your stickers, so you might as well try it.

There are special car detergents, filling, general car accessories stores have, spray it and wipe it off.