Treasure Platinum s watch is inaccurate if it falls for a while, can it be warranted?

There are three main reasons why mechanical watches are inaccurate.

1.Watch magnetization: The watch is in too much contact with items with magnetic fields, which leads to the phenomenon of magnetization of the watch, causing the watch to be inaccurate.

After being magnetized, the watch may stop, slow, or fast. After the watch is magnetized, its magnetism will not recede on its own, and it needs to be demagnetized to restore it to normal.

2.Lack of maintenance: If the watch lacks maintenance, it will lead to wear and tear of parts, dry up the sludge, affect the normal running time of the watch, and make the watch appear fast and slow.

3.Mechanical failures: Mechanical failures such as watch balance spring failures, escapement failures, and component slips can cause the watch to be fast and slow.

Mechanical watches are sometimes fast and sometimes slow, and it may be caused by severe impacts, water ingress, etc. Quartz watches are generally very accurate and less prone to time failures. In the case of adequate maintenance, it is more likely to be fast and slow, which is more related to the failure of the circuit board, or the poor contact of a certain part.

Blancpain is guaranteed for life, and you have to go to the store, Blancpain produces its own movements, after all, such an expensive thing, hundreds of thousands of watches.

First of all, make sure whether the warranty card is kept, and secondly, whether the warranty time has passed?

Room 2513, 25th Floor, Diwang Building (Shun Hing Plaza), No. 5002 Shennan East Road, Luohu District, Shenzhen, Guangdong Province] will answer for you.

1 .Problems with the quality of the watch, such as the quality of the resonator, etc., cause inaccurate timekeeping and need to replace parts.

2 .Problems with consumer usage habits. If it is a quality problem of the watch, it can be inspected by the relevant inspection departments of the state.

If it is a quality problem, the merchant must return and repair it according to the regulations. If it is a matter of usage habits, it depends on the situation. The general reason may also be that the watch is not running accurately, and the watch is close to a strong magnetic field.

1. Need for maintenance: The lack of oil in the movement or the slow wear and aging of the internal parts may cause time problems, and it needs to be sent to the designated maintenance point for maintenance services.

2. Hit or impacted: The watch is very precise, if it is hit or disturbed, it may cause loose damage to internal parts, and it may also cause timekeeping problems.

If your watch suddenly does not go, then it is likely that the table has no output signal due to the following reasons, and all other aspects of the inspection are normal, check the circuit board with a multimeter without output signal, most of the reasons are due to the damage of the quartz oscillator or the failure of the integrated circuit, if the replacement of the quartz oscillator is invalid, then the entire circuit board needs to be replacedGear train faults, most of them are dust or foreign matter between the gear teeth, so that the gear train teeth are stuck with each other. There are also some tables where there is too much or very little oil, and too much oil causes adhesion between the wheels, wheels and splints.

Too little oil makes the rotation wheel train too resistant, which will make the electronic watch go badly. In case of these faults of the stepper motor and wheel train, they should be cleaned, removed from foreign matter, and refueled.

Coil breaking, due to oxidation or man-made reasons, so that the coil is damaged, can be checked by multimeter testing, and generally needs to be replaced. The meter battery is not charged or the capacity is insufficient, and a new battery needs to be replaced. However, the watch often finds that the battery is dead in a short period of time, which is generally caused by high power consumption or the low quality of the battery itself.

In this case, you should first find out the cause, troubleshoot, and then replace the battery with a new one. The contact is not good, most of them are dirt on the positive and negative electrode contact reeds, and the contact with the battery is poor. Poor contact can also occur when the signal output point on the board is in contact with the lead point of the coil tip.

These will cause the circuit not to be turned on, so that the watch does not go or does not go well, and it is found that the circuit is not open due to poor contact, first clean the contact surface sufficiently, and then reassemble it. The stepper motor can not rotate, and the rotor of the stepper motor is a permanent magnet, which often cannot rotate due to the adsorption of iron filings and the stator is stuck, causing the watch pointer to stop or stop when walking.

Five common reasons for watch time error and watch time inaccuracy:

1) Insufficient power reserve: You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is very small, it may also cause insufficient power reserve, you can replenish the power by manual winding, and then observe whether it continues to have the phenomenon of fast and slow.

2) Insufficient power: If the quartz watch suddenly finds that it is slow, it is likely to be caused by insufficient battery energy, and you can send the watch to a special maintenance point to check the power.

3) Hit or hit: The watch is very tight, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause the problem of running time. This is to be dealt with in a timely manner.

4) Need to maintain: The lack of oil in the movement or the wear and aging of internal parts may cause time problems, which need to be maintained, and need to be sent to the designated maintenance point for maintenance services.

5) In addition to the above common situations, the watch is affected by some ambient temperatures: if the hairspring of the watch is magnetized, the watch will not be accurate.

The watch is very tight, and if it is hit or dropped, it may cause loose damage to the internal parts, and it may also cause problems with timekeeping.

1. Need for maintenance: The lack of oil in the movement or the wear and aging of internal parts may cause time problems, and it needs to be sent to the designated maintenance point for maintenance services.

2. Hit or hit: The watch is very precise, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause time problems.

Our mechanical watches often have the situation that the time is not accurate, and most people wonder if the mechanical watch is broken. There are many reasons why a mechanical watch can be parked, but there are several main reasons.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

There will be after-sales ** on your warranty link, call after-sales ** to inquire about the after-sales address.

Although Blancpain watches are luxury goods, they also require care to keep them in use. Therefore, it is important to understand how to care for your watch for your watch The following professional redressers will introduce you to the care of famous watches and watch maintenance methods.

Professional reticlers point out that watches should only be scrubbed with clean water. On the glass surface of the watch, you can drop one or two drops of water first, and then squeeze a little toothpaste to wipe it clean.

The waterproof of the watch depends on the waterproof rubber ring on the watch glass, back cover, watch handle, etc. to meet the corresponding standards. Any waterproof watch should not be worn in a hot bath, sauna, or in an environment with large temperature changes. Because the waterproof rubber ring is affected by temperature, it will expand and contract, voids will appear and accelerate aging, which will cause water ingress and water condensate in the surface, which will seriously damage the parts.

The waterproof rubber ring and handle of the watch (including the waterproof ring) should be replaced regularly according to the use of the watch. Quartz watches must be replaced with waterproof parts at the same time when changing the battery to ensure good waterproof performance. After the watch enters the water, pull out the handle, and place the watch in the sun, but do not explode the sun; It is best to keep the watch sealed with a granular dry substance, and after a few hours, remove the watch to eliminate the standing water in the watch.

Dust: Dust may seem to us to have little to do with watches, and one of the three natural enemies of the movement itself is dust. Prolonged exposure to dust-dense areas will naturally lead to the leakage of dust in the crevices of the case.

The increase in dust will lead to a faster drying of the movement's oil. This is undoubtedly a bad thing for the movement. Of course, there are not many opportunities to be exposed to dust for a long time in daily life, but it is quite useful to put a cleaning cloth and properly wipe the watch case.

Once you know how to care for our watches, you can buy the other watches you love with confidence! Now go to the world's leading one-stop service for luxury goods!