How do I change the oil at home? How to change the oil yourself at home

1.Now put the two iron frames (rhinoceros ramps) under the front wheels, and be sure to use jacks in case of accidents.

2.Hang in first gear, open the door, look at the front tire, slowly open the iron frame, stop, and pull the handbrake.

3.Open the engine cover and loosen the oil filter with a special wrench so that the oil does not leak. Open the oil cap to facilitate smooth oil draining.

4.Use the socket wrench of 9 16 to loosen the oil drain screw, then bring the rubber sheet, turn the screw with the right hand sleeve, take the waste oil basin in the left hand, and wait for the oil hall to come out, and then put the basin on the ground to connect the old engine oil.

5.After the old oil is thoroughly cleaned, unscrew the oil filter, replace it with a new one, tighten it by hand, then add the oil liter and screw the oil cap.

6.Start the car, release the handbrake, pull the car back, and check the oil gauge again. You're done.

It is best to go to a repair shop or a 4S shop to change the oil.

1.First, for safety reasons, if you only use the jack on the car, the space under the chassis is still relatively small, and the activity space below is relatively small. You know the slightest carelessness.

2.The second is a professional problem, most of the current fuel tanks are aluminum products, and if the bolts are not tightened too tightly, it will lead to slippery wires, and too loose will lead to oil leakage. Moreover, when changing the oil, the oil filter element is generally replaced at the same time, and the oil filter element needs professional tools to be unscrewed.

3.Thirdly, if you don't have professional tools, you can't put the waste engine oil cleanly, so you have to use special tools to suck it out thoroughly.

To change the oil, you have to go to the bottom of the car, and you have to drive the car to a higher place to get people in. After the oil is discharged, wash the inside, and then wash the core of the oil filter.

There is no need to pour the oil, the internal parts of the engine are originally covered with a layer of oil film when the oil is changed, and the oil will reach each part in a short time after starting the engine after changing the oil. A few seconds will not affect the engine. Besides, the transverse filter can't hold much oil.

The way to change the oil at home is to unscrew the bolts of the oil pan, open the oil filter with a special wrench, install the new oil filter with a wrench, and pour the oil that meets the specifications (an appropriate amount) into the oil pan to replace it.

The oil level should not exceed the maximum tick mark (max), otherwise it will not only increase the loss of internal power of the engine, but also fill a lot of carbon deposits in the long run, and in serious cases, there may be a phenomenon of burning engine oil. It is important to know that the consequences of burning engine oil are very serious, causing the blockage of the three-way catalytic converter, and even direct scrapping is also possible.

It is best to choose a place with a trench for gravity replacement to operate, SUVs or off-road vehicles with a higher chassis can also drill into the bottom of the car for operation, if the car can not drill in, it is recommended to use a vacuum pumping machine to replace, and it is not recommended to use a jack to support the body operation to avoid potential safety hazards;

With car insurance.

Bai has a large amount of DU increased, and most people have a car but a dao

I don't know if you go to care for it, version of yacco France.

The engine oil right brand will share with you today how to replace the oil filter.

Tools Required: Raw materials.

1. A barrel of oil that meets the lubrication standard, an original machine filter, a machine filter tool 2, a live wrench or a board suitable for the size of the oil bottom screw, an oil basin, and a cotton cloth.

1. Start the vehicle for about 1 minute to make the oil flow fully, and then turn off the engine.

2. Open the oil filling port cap and loosen the filter and oil bottom screws with tools.

3. Place the oil basin under the oil bottom screw, completely loosen the oil bottom screw, and release the old engine oil until it does not flow at all.

4. Tighten the oil bottom screws and wipe off the excess oil stains with a cotton cloth. Unscrew the old filter, it is recommended to put a cotton cloth on the hot hands carefully, apply oil to the sealing ring of the new filter, and tighten it in a clockwise direction.

6. Restart the engine for 1-2 minutes, observe whether there is oil leakage at the oil bottom screw and the filter, and if the oil leaks, the engine should be turned off in time for inspection and treatment; If there is no oil leakage, check the oil quantity of the dipstick after the ignition is turned off, add it to the standard position (the position where the center line of the oil scale is up), and replace it.

The key is what to do with the old engine oil that is released? Dump directly into the river to pollute the environment.

1. Start the car engine first, and then extinguish it when the water temperature reaches the normal range. The car can then be lifted using a jack or a car lift.

2. Then open the oil port at the bottom, and use a special wrench to open the oil filter element, you should know that the flow rate of the oil port is very slow, and you can open the filter element for secondary release at this slag time. However, it is important to note that you must wear gloves during this process, after all, the oil and filter cartridge are very hot.

3. After the last wheel, when all the oil is clean, use a wrench to install the new oil filter. Pour the oil that meets the specifications (just the right amount) into the oil pan and you're done, but be sure to aim at that mouth, and use the funnel to fill if you can't do it.

4. Of course, we also have to start the engine to see if the oil volume is normal, which is to check whether there is any leakage in the lower part of the engine.

How to change the oil in the car:

1. Disassemble the bottom guard plate of the vehicle, expose the oil filter and oil drain screws, unscrew the oil drain screws on the oil pan, pay attention to the oil will spray out instantly, and the temperature is high, move the fuel tank to the bottom of the vehicle to hold the old engine oil;

2. Remove the old oil filter with a tool and turn it counterclockwise, apply a layer of oil to the rubber ring part of the edge of the new oil filter, then install it back in place, and then tighten the oil drain screw, don't push too hard, so as not to overflow the thread;