Washing machine failure, washing machine common faults

The water level switch problem, you first blow down according to the method downstairs Suck down the hose, if it doesn't work, find the water level switch There is a small screw on the water level switch Clockwise twisting is to raise the water level under the standard situation Counterclockwise twisting is to lower the water level Like you, it should belong to the water level is too high, you twist a few times counterclockwise to try to slow down Slowly twist in the case of dehydration Twist until you hear a snap The motor starts to work It's almost enough Then in the case of laundry, adjust the water level switch repeatedly according to the usual experience of the water level Until you are satisfied Finally, it is OK to try dehydration, and sometimes this situation can be adjusted after changing the computer board, and there is a situation that your water level switch is originally broken, causing the computer board to burn out, and the actual situation is best known to you You judge whether the computer board is damaged and the water level switch has anything to do with it, and then troubleshooting.

You see if the rubber tube of the water level sensor is falling off, if it is, you can take care of the lower end, blow from above, pay attention to the water in the washing machine when blowing, and then press the blowing end to the water level sensor, be careful not to let the flow out. If it doesn't come down, it's a problem with the water level sensor.

It should be a problem with the computer version of the program.,There should be a sensor that senses the water level.,Close the water inlet valve after reaching the set position.,Then click to start.,If it goes all the way to overflow, it may also be a problem with the water level sensor.。

Take a look at the water level sensor! And what the machine turned out to be faulty.

The common faults of washing machines are as follows:

The power switch cannot cut off the power of the washing machine, please ask the company's maintenance personnel to repair it.

Abnormal water pressure makes the water inflow too small, so try to increase the water inflow.

If there is no drainage within the specified time, the drainage pipe is not buried and the drainage pipe is not buried and put down or the drainage bend is blocked, put down the drainage pipe or remove the blockage.

After the appointment started, the door lid was not closed.

Set aside the laundry and place it evenly around the bucket.

The undervoltage protection voltage rises and starts, and everything returns to normal.

The appointment time is not enough to increase the appointment time.

The common faults of washing machines are as follows:1. E0: The power Kaicong switch fails to cut off the power supply of the washing machine, and the company's maintenance personnel are requested to repair it.

2. E1: The water inlet is abnormal, the water pressure is too low, the water inlet is too small, and try to increase the water intake.

3. E2: If the water is not discharged within the specified time, the drainage pipe is not put down or there is a foreign object blocking in the drainage system, put down the drainage pipe or remove the blockage.

4. E7: After the appointment is started, the door cover is not closed and the door cover is closed.

5. E4: The washing is on the side of the trembling, and the washing is evenly placed around the barrel.

6. E5: Low voltage protection will be started when the voltage rises, and everything will return to normal.

7. E6: The appointment time for staring at the lead cherry blossom is not enough to increase the appointment time.

The common faults of washing machines are as follows:

The power switch cannot cut off the power of the washing machine, please ask the company's maintenance personnel to repair it.

Abnormal water pressure makes the water inflow too small, so try to increase the water inflow.

If there is no drain within the specified time, the drain is not lowered or the drain system is blocked, lower the drain or clear the blockage.

After the appointment started, the door lid was not closed.

Set the washed laundry aside and place it evenly around the bucket.

The undervoltage protection voltage rises and starts, and everything returns to normal.

The appointment time is not enough to increase the appointment time.

There can be many kinds of washing machine failures, here are some common ones and how to fix them::

1.The washing machine does not start: check whether the power plug is plugged in tightly, whether the power supply is normal, and whether the switch is damaged.

2.The washing machine cannot drain water: check that the drain pipe is blocked by the cruise ship and that the drain pump is damaged.

3.The washing machine cannot be filled with water: check whether the faucet is open, whether the water inlet pipe is blocked, and whether the water inlet solenoid valve is damaged.

4.The washing machine does not turn: check if the belt is loose or broken, and if the motor is damaged.

5.Washing machine leakage: Check that the washing machine door seal is intact and that the drain pipe is loose or broken.

6.The washing machine is noisy: check whether the base of the washing machine is stable, whether the belt is loose or broken, and whether the motor is damaged.

7.Poor washing effect of the washing machine: check whether the washing machine drum is clean, whether the laundry detergent is sufficient, and whether the washing machine needs to be cleaned.

If the above methods of the portable shrine cannot solve the problem, it is recommended to contact professional maintenance personnel for maintenance.

The washing machine can not enter the water or has been entering the water, has been draining or can not discharge the water, can not dry the water, the washing machine does not turn, etc. are common faults of the washing machine, and after checking according to the steps, targeted maintenance is required.

Solution: 1. Water inlet failure: If you can't enter the water, you need to check whether the water source is open, whether the water inlet pipe is blocked by impurities, whether the water inlet valve coil is burned, and whether the washing machine program is normal; Check the water level sensor, inlet valve and panel for failure all the time.

2. Drainage failure: can not drain, may be a problem with the drainage valve, the drainage valve is blocked by debris or the drainage hose is bent and deformed, the gap between the drainage rod and the rubber valve is too large, the trap spring loses elasticity, the drainage solenoid valve is faulty, the computer board is faulty, and the above problems can be solved by checking and repairing them one by one; Keep draining the water and check whether there are foreign objects stuck in the valve and computer board faults.

3. Dry water: too many clothes are washed, the lid of the washing machine is opened when washing clothes, low-speed dehydration is chosen when washing clothes with strong water absorption, and the failure of the drainage system will cause the washing machine to not dehydrate.

4. The washing machine does not fail to rotate due to motor failure, wave wheel screw falling off, wave wheel bayonet damage, belt aging or falling off, computer board failure, etc., which will cause the washing machine not to rotate.

Generally, the most common problems are the solenoid valves, computer motherboards and the drainage system of washing machines. In the operation of the washing machine, these components are used more frequently. The following is to give the corresponding fault handling steps according to the part in question:

1. Solenoid valve. Generally, the failure of the solenoid valve is rust or short circuit. Because the solenoid valve drives the washing machine to rotate, it is needed for all the procedures of the washing machine.

When there is a problem with the solenoid valve, you need to open the back cover of the washing machine to find the position of the solenoid valve, if you find that the solenoid valve is rusty, you need to use a special rust remover to clean it. If the solenoid valve is damaged by a short circuit, it needs to be replaced with a new solenoid valve.

2. Computer motherboard. Generally, the problems that occur in computer motherboards are moisture failures caused by water vapor. Therefore, it is recommended that the washing machine be installed in a slightly drier location as much as possible, and the lid should be opened when the washing machine is not in use, and the waterproof vapor can also prevent bacteria inside.

If the motherboard is damaged, it will need to be replaced with a new motherboard.

3. Drainage system. The drainage system mainly refers to the drainage nozzle and drainage pipe. Sometimes some fluff on clothes is easy to block the drain mouth, causing drainage failure.

In the event of this failure, you need to use a thin wire or toothpick to clean the drain hole, and the drain pipe needs to be rinsed with a water gun, and then the drainage of the washing machine can be normal.