What should I do if there are bubbles after the tempered film is pasted, and what is the reason for

You can use this small piece of cloth to push the bubbles on the screen first, so that the contact area between you and the entire screen becomes larger, and there will be no gaps when pushing to let the bubbles run away. You can also fold the cloth in half a few times when pushing, and then use its edge to push the bubbles.

After pushing a few times, you will find that there will still be a few very fine bubbles on the mobile phone screen, and even if you push it a few more times, you will still find that this bubble will not be removed, that is, because this bubble has quite fine dust in it, which is a fine bubble formed by dust, so no matter how you push with a cloth, if you don't remove the dust inside, there will always be such bubbles. At this time, all we have to do is to remove the dust inside the bubble.

At this time, you can use the tape, maybe you think of using the tape to stick the fine dust, in fact, this is the method, but we still need to do some skills when using. You can cut a piece of tape, and then stick it directly on the phone screen, and then pull up this piece of tape, and the stickiness of the tape can pull the film up the way. Only a small gap is needed, and then a small piece of tape is cut out, and the dust on the screen or film is directly glued off, so that the whole phone can become more clean and tidy very effectively, and finally the film is pasted on the mobile phone, and finally you can find that many of the original bubbles are basically gone.

How to solve the problem of bubbles on the edge of the mobile phone tempered film.

Method 1: We can fold a piece of hygiene into a thicker and softer square, and then aim at the bubbles to push and press out, give priority to the large bubbles in the process of pushing, and push the bubbles to the edge of the film. When handling small bubbles, try to push them out as close to the edge as possible.

Method 2: Push the hard card next to the film with appropriate force, and give priority to the large bubbles in the process of pushing. When you push it to the edge of the film, you can let the bubbles dare to go out. When handling small bubbles, try to push them out as close to the edge as possible.

Method 3: Sometimes the bubbles are often caused by dust in the film, so you can gently lift up the dusty side of the film, use transparent glue to wipe off the dust inside, and then gently put down the film. Then use toilet paper.

Or just press the glasses cloth so that the film fits snugly against the screen, and we're done.

The above is the specific operation method of how to solve the bubbles on the edge of the mobile phone tempered film, I believe that everyone can quickly learn how to operate and deal with it through the understanding of the above content.

The tempered film generally does not have bubbles.

If you can still do it next to it, if the bubble is in the middle, you will have to replace it from the beginning. The film application speed must be fast, otherwise there will be too much dust.

If there are as many bubbles as there are in the normal membrane, I can clean them out.

Reasons: 1. Tempered film quality problems.

Second, in the normal use of the mobile phone, it is inevitable that there will be various pressures on the mobile phone screen, and the force is uneven in various places, and there will be bubbles for a long time.

Method of pasting mobile phone tempered film:

First, clean up the dust and oil stains on your hands first, and wash them with hand sanitizer.

2. Wipe the surface of the mobile phone with a glasses cloth or a soft cloth that does not shed a small amount of water, and clean up the dust and fingerprints on the surface.

3. Tear off one side of the protective film, then aim at the phone, align the top and left sides of the film and paste the film.

Fourth, slip or when sticking the film, try to maintain a constant speed, and pull back less when bubbles appear to ensure that there are no bubbles on the surface of the film. Then use wool felt.

Scrapers, or padded scrapers, to avoid scratches. Slowly press the film little by little on the surface of the phone, in this case, there will be few bubbles instantly.

Fifth, after the paste, repair the bubbles in some areas. Wrap the credit card with a hard card, credit card, etc., with the soft cloth that just wiped the screen of the letter, and then slowly exert force to scrape the bubbles out of the edges.

Introduction to tempered film:

Tempered glass mobile phone film.

It is a new mobile phone protective film launched in China in 2012, and it is currently the most powerful high-end new product to protect the screen.

The thickness of this protective layer is only millimeters, and the high silver can completely cover the original screen surface, prevent damage and scratches by external forces, and increase the impact absorption, which is 5 times higher than the standard of PET film. It does not affect the effect of the screen.

Air bubbles in the mobile phone film can be removed using tools such as hard cards, hair dryers, lubricating fluids, and sandwich hole yards, as follows:

1. Use a hard card or bank card to pry open the corner close to the bubble, and the bubble will disappear after full contact with the air. Then use the bank card to press the unopened tempered film.

Slowly press the tempered film forward so that the lifted part can also come into contact with the phone screen and glue together. Finally, gently scrape the phone screen with a bank card to make it look neat and comfortable.

2. Turn on the power of the hair dryer and turn on the hot air.

Blow against the screen of the phone, and turn off the hair dryer immediately after the screen softens.

Then press the bubbles in the tempered film with your fingers, and the bubbles will disappear after pressing for a while.

3. Dip a toothpick in a little lubricating liquid, and then lift the corner close to the bubble, so that the lubricant on the toothpick is in direct contact with the bubble. When the lubricating fluid comes into contact with the bubbles, the stubborn bubbles disappear.

4. In the face of the bubbles in the tempered film, the simplest and rude way is to use a clip to clamp the mobile phone to temper the bubbles in the film. The next morning, you'll find that the bubbles and everything are gone, and the phone is still as comfortable as it used to be.

Precautions: 1. If you buy a non-customized film, you need to prepare scissors, rulers, pens, and non-woven fabrics, and cut the film and equipment on a flat desktop to fit the device screen. Cutting should be fast, accurate, and a success, so that it is beautiful.

2. If you buy the original film that matches your own equipment model, you don't need to cut it separately, but you should choose a good room for filming, the light should be good, and the room should be clean and free of dust.

3. The film is to wash your hands well, and dry the water on your hands, so as to keep your hands clean and dry.

Very small bubbles will disappear from the sedan state, and if the bubbles are closed, they must be lifted and exhausted to disappear. Mobile phone film.

The reason for the bubbles is that there is a large amount of air between the mobile phone film and the mobile phone screen during the pasting process, which will cause a large number of bubbles to appear on the mobile phone, and this bubble is air.

If you want to have no bubbles in the mobile phone film, you need professional film tools, including mobile phone film scrapers, wet wipes and dry paper towels, for these tools must have, these are professional tools for mobile phone film, in order to have a better film effect.

There are air bubbles in the tempered film, which can be removed with the help of tools such as scrapers, and the operation method is as follows

Tools: scraper, tempered film.

1. Pick open the gaps.

Find the corner of the newly applied tempered film and pick it open with your hand.

2. Use a scraper to scrape out air bubbles.

After lifting a slit, use a scraper to start scraping close to the bubbles.

3. Compress the tempered film.

After scraping out the bubbles, re-press the edges of the tempered film by hand.

Precautions for pasting tempered film1. Pay attention to wipe the screen with your own film. If you want to apply the film yourself, pay attention to wipe the screen clean, this is very important, generally there will be a wiping cloth in the film, and you must thoroughly wipe the fingerprints and dust on the screen.

2. When sticking the film, pay attention to the uniform pasting, and try not to produce bubbles, otherwise it is easy to enter the air and dust, and you can't see the patterns and subtitles on the screen clearly, which is easy to cause visual fatigue. If you can't stick it yourself, it's best to go to a professional store to find someone to apply the film.

Pro-[warm] bubbles after pasting the tempered film is a relatively common situation, and the following methods can usually be tried:1Extrude bubbles:

Use a card or fingernail to gently squeeze the edge of the bubble outward until the bubble is completely extruded. 2.Remove air bubbles:

If the bubble is large or the squeeze cannot be solved, you can use a special bubble remover or similar gadget for the mobile phone screen protector to suck or squeeze out the bubble. 3.Wait for the bubbles to disappear:

In some cases, small bubbles may disappear on their own within a few days or weeks without affecting use. Note: In the process of handling air bubbles, avoid using sharp objects to cut the surface of the tempered film to avoid scratches and damage.

At the same time, it is recommended that Mengyin clean the mobile phone screen before the film to ensure that there are no impurities such as dust and grease on its surface, so as not to affect the effect of the film.

1. Hard card processing.

If you paste a tempered film.

If there are air bubbles, first pry open the corner of the bubble with a hard card, and the bubble will disappear after full contact with the air. Then use the bank card to press the unopened tempered film part and slowly press the tempered film forward, so that the pried part is in full contact with the mobile phone screen and is tightly bonded. Finally, use the bank card to scrape the phone screen back and forth several times to make the tempered film look flat and bubble-free.

2. Hair dryer treatment method.

First of all, turn on the power of the hair dryer and turn on the hot air of the hair dryer.

file, blowing on the screen of the phone, after the screen softens, immediately turn off the hair dryer.

Then press the bubbles inside the tempered film with your fingers, and after pressing for a while, the bubbles will disappear. It should be noted that when using a hair dryer, you must control the time well to avoid damage to the mobile phone screen if the temperature is too high.

3. Lubricating fluid treatment method.

First, use a toothpick to dip an appropriate amount of lubricating liquid, and then pry open the corner of the mobile phone screen close to the bubble, so that the lubricant on the toothpick is in direct contact with the bubbles.