-
In the process of using Windows 10 system computers, you will often encounter some tricky networks.
Recently, a win10 system user reported that the computer could not be connected, and the word "recognizing" was displayed under the ethernet.
If this happens, we can solve it in the following two ways.
Method 1: 1. Right-click on the start menu and click the [Network Connection] <>
2. Right-click on the Ethernet network and select Disable
3. Wait for "Disabled" to be displayed, then right-click again, select [Enable] and wait for the network signal to be automatically obtained.
Method 2: 1. Right-click on the start menu and select [Command Prompt (Administrator)] <
2. Input: netsh winsock reset press enter to execute the command.
3. Restart the computer when prompted, and the problem being identified can be solved after restarting the computer.
-
Connecting to a network The network you are using may ask you to access its login page is caused by a network error, and the workaround is as follows:
1. First of all, find [Network and Sharing Center] in the control panel.
2. After entering the [Network and Sharing Center] of the pin, click [Change Adapter Settings] to find the corresponding network card.
3. Right-click at the corresponding NIC adapter and select [Disable], then the NIC will be grayed out and disabled.
4. Finally, right-click again and select [Qizu Fiber], and the network card will be reconnected at this time, as shown in the figure below.
-
There are several scenarios in which this problem occurs:
1. The NIC driver is missing.
For example, when uninstalling some software, the shared file is also removed, resulting in the loss of the network card driver, so there will also be a difference in the network connection, you can find out if there is a network adapter in the right-click properties of my computer - hardware - configuration manager.
2. The router crystal is only the head and the network pure training line is not in good contact with the network cable of the router or cat.
Therefore, the crystal head should be re-plugged, and the router or cat network cable socket should also be re-plugged to see if the indicator light of the network card is flashing, and it is flashing normally.
Extended information: A router (also known as a pathfinder) is a computer network device that can transmit data packets through a network to a destination (selecting the transmission path of data), a process called routing. A router is a device that connects more than two individual networks, and routing works at the third layer of the OSI model, the network layer, such as the Internet Protocol (IP) layer.
A router is a device that connects to various LANs and WANs on the Internet, and it automatically selects and sets routes according to the conditions of the channel, and sends signals in the order of the best path. A router is the hub of the Internet"Traffic police"。At present, routers have been widely used in all walks of life, and various products of different grades have become the main force to realize the internal connection of various backbone networks, the interconnection between backbone networks, and the interconnection between backbone networks and the Internet.
The main difference between routing and switching is that the switch takes place at the second layer of the OSI reference model (data link layer), while the routing takes place at the third layer, which is the network layer. This difference determines that routers and switches need to use different control information in the process of moving information, so the way they implement their respective functions is different.
-
The computer shows that the network is connected, but the reason for not being able to access the Internet is caused by a system error, the specific solution steps are as follows: 1. First turn on the computer, find the "Control Panel" option in the computer and click on the upgrade. 2. Then find the "Network & Internet" option in the interface and click on it.
3. Click "VPN" in the interface and click "Change Adapter Options". 4. Right-click on the network you are using, and click the attribute option in the options bar that pops up. 5. Finally, find "Automatically get IP address" in the pop-up interface, and click "OK" to solve the problem that the computer shows that the network is connected, but the Internet cannot be accessed.
-
Possible causes and solutions:
1. The wireless network password is incorrect. You can delete the configuration file of this wireless network, and when you connect to this wireless network, you need to re-enter the password, and enter the correct password.
2. It may be that the network is disconnected, and it has nothing to do with your machine. You can restart the router and check if the network connection on the router is working properly. Change the IP address and submask to be set automatically.
3. Check the router settings, or consult the network service provider. Please check if your local DNS and IP settings are set to"Acquired automatically"I think it should be caused by the fact that the IP address is not automatically obtained, or the network specifies a private IP range.
-
Check whether DHCP is enabled on the router.
-
The IP and DNS are all automatically obtained.
To connect to the network on a desktop computer, you need to choose a broadband PPPOE connection method, fill in the broadband account and password, and then click to connect to the broadband. The desktop computer creates a network connection as follows: 1. Click the [Start] button on the computer, then click the [Control Panel] button2, pop up the [Control Panel] window, click [Network and Sharing Center] 3, pop up the [Network and Sharing Center] interface, click [Set New Connection or Network] on the right, as shown in the following figure4, pop up the [Set Connection or Network] window, click the first item [Connect to Internet]5, click [Next], and the [Connect to Internet] window pops upIf you have already connected to a network, then select the second [still set a new connection] button and click 6, select the [broadband PPPOE] connection method 7, pop up the interface of setting broadband account password, and then click the [Connect] button after filling in the broadband account and password to connect to broadband. >>>More
Shutdown is slow. Optimized with Super Bunny.
End all applications, end all programs in memory. >>>More
Your computer can enter the route?
Don't change the IP >>>More
First, the CMOS battery on the motherboard is out of power. The chassis can be opened. Replace the CMOS battery with a new one. >>>More
It should be a problem with the system and can be done as follows: >>>More