What is the channel steel layer of a 33 storey building?

The channel steel layer of the 33-storey building is generally on the 3rd, 10th, 17th, 24th and 31st floors, because the channel steel layer is generally built every 7 floors.

The channel steel layer is usually located in the basement or the top floor and roof; When the building has a large number of floors (high-rise), the channel steel layer is usually located in a certain layer in the middle of the building. When buying a house, consult the sales department of the developer. The height of the channel steel layer is generally 2 2 meters, and the specific floor is 10 to 20 floors, and the lowest floor height is the channel steel layer.

There is no fixed floor standard for the channel steel layer, and the position of the channel steel layer is different in different buildings.

The channel steel layer of high-rise buildings is located on the first floor or about the 7th to 8th floor, which is built by many long strips of steel with grooved cross-sections.

The channel steel layer will make a lot of noise when people walk on it, and there will be a certain amount of shaking, which will have a lot of impact on life, and the channel steel stretched out by the channel steel layer of the house will often be corroded by rain, ice and snow, and it will not only affect the appearance of the house for a long time, but also have potential safety hazards.

For floors, channel steel floors are usually on the 3rd, 10th, 17th, 24th and 31st floors.

2. Because the channel steel layer is usually built every 7 layers, the channel steel layer is built by many channel steel, if it is used as a small compartment, there is no problem at all, so you don't have to worry about safety issues.

3. In the process of building a house, people will treat the channel steel properly, such as anti-corrosion treatment and tight wrapping, so we don't need to worry about the corrosion of the channel steel layer.

Most often, the channel steel layer.

Generally, the floor begins to be cantilevered at the position of the top plate of the third floor, and it is generally picked every six floors, and the first floor is the landing price.

Seven floors and thirteen floors are cantilevered. The high-rise channel steel is generally 3 layers, 3 + 7 = 10 layers, 10 + 7 = 17 layers, 17 + 7 = 24 layers, 24 + 7 = 31 floors, etc., so if it is a 34-story house, then the channel steel layer is generally set in 3 floors, 10 floors, 17 floors, 24 floors, 31 floors, etc.

When choosing a floor, it is not recommended to choose the following floors:

1. Don't choose the first layer.

Because in high-rise residential buildings.

In the community, the first floor is the most uneasy floor. Because it is relatively close to the ground, it is more affected by the environment, such as rain, noise, insects, etc. Therefore, the living comfort will be relatively low.

2. Don't choose the top layer.

At present, in high-rise residences, the top floor is generally equipped with a top floor garden, so as to cool and insulate the residents on the top floor, waterproof and other functions. But because it's cold at a high place.

It is also more affected by the environment, especially storms.

The weather, unsettling.

3. Do not select the equipment layer.

High-rise residential buildings must be set up, and air conditioning, water supply and drainage will generally be placed on the equipment floor.

Electrical, elevator machine room and other equipment. As a result, adjacent floors are subject to noise or mechanical vibrations.

In most cases, the selection rule of high-rise residential floors is more than one-third and less than two-thirds of the total number of floors, and the floors in this range are better choices.

1) The lighting is very good, the sunshine time is long, and the vision is very wide, because there will generally be no buildings to block;

2) Secondly, in the event of an accident such as a fire, the floor may be too high.

Increase the difficulty of rescue, and the floors in this range, compared to the higher floors, are still okay.

2. In actual life, it is recommended to choose the floor according to the living habits of yourself and your family, as well as your health. After all, the house is for living, and you don't have to pursue the best floor in other people's mouths, the floor that suits you and can meet your needs is the best floor.

For this layer, there are some buyers who believe that they know it, but many people do not make it clear. So what is a channel steel layer? As the name suggests, it is the steel bar that is laid when building a house.

Its load-bearing capacity is relatively good, and it can play a fixed role when building an outdoor frame, and then these channels will be removed in the later stage, but the wall will leave holes.

So why isn't it recommended to buy it? Because this layer will leave holes after the rebar is removed. Once the developer's waterproofing is not done well, the chances of leakage on the exterior wall will be relatively large. Water leakage is a particularly difficult thing to deal with.

In addition, if you buy a channel steel layer that was built before, there will be rust, and it will affect the firmness of the building over time. You may not have this concern when buying a new house, but when buying a second-hand house with a long life, you should pay special attention to the channel steel layer and try to avoid it.

What are the general layers of channel steel? Generally, it is on the top floor or the middle floor, but you still have to ask the sales staff for details.

9th floor, 16th floor, 23rd floor.

Generally speaking, the livable floors of buildings with different total floors are different, and the best floor of the building is between 3 1 and 3 2 of the building, so you can confirm the total number of floors of the building before choosing the floor of the house. For example, the total number of floors is a 30-storey building, and the livable floors are between 10-20 floors.

The effect of the channel layer.

It is necessary to pay attention to the house made of channel steel, when people walk on it, there will be a certain shaking sound. The smaller the channel steel specification, the louder the shaking sound, and the larger the channel steel specification, the smaller the shaking sound, so it will have a certain impact on residential life.

It should be noted that the edge of the channel steel of the previous channel steel layer will be exposed to the outside, and when it rains and snows, the water will flow into the building through the channel steel, and seriously it will penetrate into the house, causing the wall to be soaked in water and bringing unnecessary trouble to the residents. Moreover, the previous channel steel will rust when exposed to water, and it will also affect the firmness of the building for a long time.

However, the channel steel package of the channel steel layer is treated quite strictly, and the surface of the channel steel will be coated with a thick zinc layer to generate a zinc-iron alloy, which makes the channel steel have considerable corrosion resistance, so there is no worry about buying the channel steel layer now.

The above content refers to Encyclopedia - Channel Steel Layer.

The channel steel floors of 33-storey buildings are usually on the 3rd, 10th, 17th, 24th and 31st floors.

For buildings with a height of less than 30 meters, the channel steel layer is usually located in the basement or top floor, the roof. When the building has a large number of floors, the channel steel layer is usually located on a certain floor in the middle of the building. When buying a house, you can consult the sales department of the developer, and the general high-rise residential buildings usually have a channel steel layer on 10-20 floors.

The floor height of the channel steel layer is generally meters, and the specific floor is found to be 10 to 20 floors, and the lowest floor height is the channel steel layer.

As construction equipment generates sound, vibration, radiation, etc. during operation. If the sound insulation and shock absorption measures are not good, the room near the channel steel layer is susceptible to noise and vibration. Therefore, try to avoid the channel steel layer when buying a house.

Disadvantages of the channel steel layer.

1. Easy to leak. The channel steel layer is prone to water leakage. Because the channel steel layer will be cantilevered during construction, although it seems to be no problem temporarily, if the construction is not in place, it is easy to leak water in the later stage, or cause snow and rain water to flow into the building, resulting in water immersion in the wall.

2. Easy to rust. The previous channel steel layer will not only leak, but also rust when the channel steel encounters water, and the firmness of the house will not be guaranteed after a long time. However, the houses built now, even the channel steel layer, are reinforced, and the surface of the channel steel is coated with anti-rust paint, so there is no need to worry too much.

3. Noise interference. Since the channel steel layer is built with channel steel, it will shake compared to other floors, especially when people walk on it, there will be a squeaky sound. Generally speaking, the smaller the size of the channel, the louder the shaking sound.

Nowadays, residential buildings are made of large channel steel, and the general sound is inaudible.