Solid wood flooring is a little damp on the low surface, I feel that it is not dry, can it be paved

It must not be paved, after paving, the moisture of the ground has no source to emanate, it will erode into the wooden floor, the light one will affect the use effect of the floor, the heavy one will warp and deform, or wait for the ground to dry out before paving. There are empty spots that are certainly not high-quality floors, and it is okay to pave them, but they affect the service life, and the empty spots are also easy to absorb moisture and produce deformation.

It is a lie to say that the solid wood floor does not have formaldehyde, ask it, there is a paint company that dares to say that his paint is formaldehyde-free, If the consumer says, the bottom surface of the floor (you mean the back of the floor), the last process of the floor in the production process is to let the floor pass the ultraviolet dryer, and besides, the rolling back of the floor is completed in the primer process, and in the end there will be no paint drying. The solid wood floor you said is multi-layer composite flooring or pure solid wood, and a little empty spot on the back is allowed. A board can not be more than three places, the process requirements are to fill putty, listening to your description, I think the quality of this floor is still problematic.

That can't be paved, solid wood flooring is formaldehyde-freeThat's right, but if it's a solid wood floor. I've been doing QC in nature for many years.

Solid wood lacquered floors are opened 48 hours before installation to allow for natural conditions before installation. In that case, there should be no problem.

Wait in the shop!! Because moisture can affect the quality of wood flooring.

The landlord hurriedly returned the goods, and this kind of wooden floor was immediately deformed as long as it was damp.

When laying solid wood flooring, you need to lay things underneath, solid wood flooring from the bottom to the surface are made of wood processing, long-term use, easy to be affected by the environment, weather and other factors, dampness. Therefore, the installation of solid wood flooring requires a moisture-proof film. Here are some of the steps to lay:

1 Use a semi-dry mop when cleaning. If the air in your home is dry, make the mop wetter or put a basin of water on the heater or humidify it with a humidifier. 2 After laying, wax in time.

In the usual process of use, waxing every 3 months is sufficient. In fact, it is okay not to beat, but frequent waxing can maintain the finish of the floor and prolong the service life of the solid wood floor. 3. Try to avoid the wooden floor from contact with a large amount of water; Avoid wiping with acidic and alkaline liquids to avoid damaging the finish of the floor surface paint.

4 Avoid sharp objects scratching the ground, do not throw cigarette butts or directly place things that are too hot on the floor, and try to avoid dragging heavy furniture. 5. During the use of the floor, if it is found that the individual floor is shelled or falling off, the floor should be picked up in time, the old glue and ash should be removed, and the new glue should be applied and compacted. Waxing once a month is also the best way to maintain it, but wipe off moisture and stains before waxing.

The above told you the methods and steps of laying moisture-proof film under the solid wood floor, have you remembered them? In fact, you just need to memorize it, the real process steps are to be handed over to the master who helps you decorate to deal with it, and there is no need to take this matter too seriously.

Homeowners should take an absorbent towel and wipe the surface of the floor clean with moisture. After that, you can turn on the hair dryer or air conditioner to dry the floor, be sure to use cold air, not hot air, otherwise the floor may crack. If the dampness is too strong and cracks have appeared, such a floor cannot be used, and a new one can only be replaced.

How do you dry it quickly?

First of all, you should use a mop or mopping machine to suck up the visible water droplets on the floor, and then use a hair dryer to blow it. Generally speaking, the skill of adding a hair dryer is still relatively good, you can turn on the maximum gear and then turn on the cold air. If it's summer, the floor will be dried in a while.

And the air is also very dry in summer, which can make the floor dry faster. But it can also cause cracks in the floor, and homeowners can take care of it, such as applying some lubricating grease to the floor. If the damp area is relatively large, you can turn on the air conditioner at home, and then turn on the upper and lower sweep and cold air stalls, so that the floor can be dried.

Do not turn on hot air as it will cause cracks on the floor.

Mop the floor with salt water.

Summary: It is best for southerners not to lay flooring at home, after all, it is particularly prone to moisture, which may make the life of the floor very short. Even if you lay flooring, you should take good care of it.

The hardwood floor is damp, and if you want to dry it quickly, you need to use a dehumidifier or turn on the air conditioner to extract moisture from the air, so that the wood floor becomes dry.

If it is just ordinary dampness, it can be dried by a hair dryer, there is a serious soaking situation, and it can only be dried slowly, and mildew must be prevented.

You can wipe it clean with a rag, wipe it almost first, and then turn on the air conditioner, raise the temperature a little, and you can dry it quickly.

If it is too wet, it is better not to pave, if you do the keel, the project is too vast and laborious and costly, and the money to make the keel is enough to buy the floor, and what is the keel made of, it is also made of wood, as long as it is made of wood, there is no fear of water.

If you really want to shop, I personally recommend that you buy a 12 cm wide board, and now the anti-solid wood floor is only good-looking, and the quality is not as good as the previous wide board. Of course, if you have money, it's better to buy solid wood.

Hehe. That's an interesting question.

The correct answer should be: as long as you do a good job of sealing the room, there is no problem.

Damage to solid wood floors caused by dampness (drying) mainly comes from the change of dampness and dryness. Among them, the biggest impact is the sudden dryness and wetness. Therefore, the chances of problems with solid wood flooring in a well-sealed space are not high.

For example, many cities in China are in basins, the climate is very humid, there are many people who use the floor, and there are few problems with the floor. On the contrary, the northwest region of our country is very dry, and there are very few people who use solid wood flooring indoors, the main reason is that the floor is generally dry and cracked (sprinkle water on the floor once the day before, and it will dry and crack the next day).

The first floor is relatively humid, if you do not do moisture-proof treatment, it is easy to cause the wooden floor to be damp and deformed, and even rot if you do not do moisture-proof treatment.

It is generally easy for us to confuse the concept of moisture-proof and waterproof, and often use waterproof methods to deal with the problem of moisture-proof, which will lead to our inability to completely solve the problem of moisture-proof on the ground. Moisture prevention needs to prevent underground moisture (water vapor), and waterproofing needs to prevent groundwater (liquid water), so it is difficult to prevent moisture from entering the room with an ordinary waterproof layer.

Moisture-proof needs to be constructed before waterproofing, and generally treated on your original cement floor and wall before decoration, only in this way can it play a fundamental moisture-proof effect, and can prevent the blistering and falling off of the waterproof layer.

First make a 100 200 high grille on the ground with concrete, sprinkle some lime or moisture-proof things on the grille façade, and then add keels to the door and lay the floor.

It is recommended not to get it, no matter how to deal with it, your wooden floor is the difference between using it for 1 year and 2 years.

The bottom layer is covered with moisture-proof mats.

For solving the problem of moisture absorption, expansion and deformation of solid wood flooring, there are:

1. Ground moisture-proof treatment method: generally use "three oil and two felt" (three layers of asphalt and two layers of linoleum paper, and then smear a layer of cement on it to prevent the release of harmful gases); The simple treatment method is to apply a moisture-proof film.

2. Balance the expansion of the plate through installation: some add a layer of wool floor to the keel, some require wide gaps between the plates, some require traps to be left at the four corners of the room to facilitate the release of moisture, and some require springs to be provided in the expansion joints of the wall floor, some use aluminum alloy keel, and some use rails.

3. First of all, you start in terms of cleaning and maintenance, rarely see water, before laying the floor, you may wish to sprinkle some peppercorns, which are both moisture-proof and insect-proof. The most effective way is to keep the floor and keel dry. When supporting the ground, the cloth has less water, and it should be noted that the mop must be wrung very dry, and there can be no dripping.

Remember to close the windows when you go out to prevent water from coming in on rainy days, and open the windows more often to let the room on sunny days.

Solid wood floor laying and maintenance points (1) The floor should be laid in the later stage of construction, and no cross construction should be allowed. It should be sanded and painted as soon as possible after laying. This will not stain the floor or deform it with moisture.

2) The reason for the resurgence of moisture on the floor is high humidity in the air, which is a precursor to rain. The higher the humidity of the air at the same temperature, the more likely it is to condense dew, especially when the temperature is still low.

I live on the first floor, can the solid wood floor prevent moisture?

Summary. Dear, I'm glad to answer for you: the characteristics of cork flooring are relatively dense, and the mute effect is good, but special attention should be paid to one that can not bear too heavy objects, long-term load-bearing may damage the board surface, this should be paid special attention; Moreover, the cork floor is pressed together with cork, and the surface is relatively rough and grooved, so it is easier to store ash and needs to be cleaned and cared for more carefully.

The waterproof and anti-corrosion properties of ordinary cork flooring are not strong, and moisture is easier to penetrate. Therefore, it is necessary to prevent ink and lipstick from getting on the floor, otherwise the dirt will not be easy to clean. If it has not been treated with moisture and waterproof, in a relatively humid environment, the cork floor is also prone to mold, so it is necessary to ensure that it is used under a reasonable environmental humidity.

Dear, I'm glad to answer for you: the characteristics of cork flooring are relatively dense, and the mute effect is good, but special attention should be paid to one that can not bear too heavy objects, long-term load-bearing may damage the board surface, this should be paid special attention; Moreover, the cork floor is pressed together with cork, and the surface is relatively rough and grooved, so it is easier to store ash and needs to be cleaned and cared for more carefully. The waterproof and anti-corrosion properties of ordinary cork flooring are not strong, and moisture is easier to penetrate.

Therefore, it is necessary to prevent ink and lipstick from getting on the floor, otherwise the dirt will not be easy to clean. If it has not been treated with moisture and waterproof, in a relatively humid environment, the cork floor is also prone to mold, so it is necessary to ensure that it is used under a reasonable environmental humidity.

Thank you for your answer, 5 stars for service.

Summary. Hello, according to your problem description, the solution provided to you here is as follows: Hello, the bottom surface is uneven plank, and you want to lay a wooden floor for the uneven ground How to lay a wooden floor:

The ground is uneven, the potholes are too big to lay the floor, the best treatment can be carried out in this way: treat with gypsum, gypsum is a good material for post-treatment of uneven ground, and it is also the easiest. Gypsum treatment of uneven ground is to add white powder inside, responsible for the unevenness of the bay when it is fast drying.

Hello, the bottom surface is uneven with wooden planks, what to do if you want to lay wooden floors.

Hello, according to your problem description, the solution provided to you here is as follows: Hello, the bottom surface is uneven of the plank, want to lay the wooden floor for the uneven ground how to lay the wooden floor This problem: the ground is uneven, the potholes are too big to lay the floor, the best treatment, you can remedy it in this way:

Treated with plaster, which is a good material for post-processing uneven floors, and is also the easiest. Gypsum treatment of uneven ground is to add white powder inside, responsible for the unevenness of the bay when it is fast drying.

The bottom is a wooden board that can be made with gypsum powder and large white powder??

Hello, according to your problem description, the solution provided to you here is as follows: the surface of the board (board) is relatively smooth, and the putty powder or gypsum powder is easy to fall off directly on the board (board). No.

If the wooden door plank is cracked, you can't use gypsum powder. Because the board has the natural phenomenon of thermal expansion and cold contraction, gypsum powder does not, it will not expand and contract with the seam of the board. The adhesion between the gypsum powder and the wooden board is poor, even if it is filled at that time, the door is moving, which will vibrate, and the gypsum powder will fall off after a long time.

The cracks in the door panel can be filled with putty first, and then painted with the corresponding color paint after drying, and sprayed with some varnish after fine grinding, but this is a bit troublesome. It is best to ask a professional lacquer repairer to deal with it. Cement mortar ground leveling:

It is suitable for all kinds of ground leveling before floor laying. This method uses the most common cement mortar, which is more moderate and acceptable to the average person. Self-leveling leveling:

Self-leveling ground leveling is a new leveling technology, which uses high-polymer self-leveling cement for ground treatment. Gypsum floor leveling: the cost of plaster leveling is slightly higher than the other two, if the entire floor is inclined, the height difference is 3 cm, the gypsum consumption will be a little large, this can be selected according to their own economic situation.