How to make a three dimensional car with paper, how to origami three dimensional car

This ** is made of Santana.

That's not bad either.

The tutorial about car origami is as follows:

Make a crease in the middle of the paper. Fold the paper in half, horizontally. Scratch a crease along the crease with your fingernails and weigh it aside.

Fold the top and bottom edges of the paper 1 3. Fold the top edge of the paper down 1 3. Next, fold the bottom edge of the paper up 1 3.

Now, you should have 3 parts of the same size on your paper.

Fold the corner of the top flap up until it goes over the folded edge. Back to your top flaps. Fold the bottom right corner up until it goes over the top fold edge.

The left point of the corner should be at 1 3 of the flap. Keep the top flap folded down. Don't want it!

Fold the other corners in a similar way. Fold up the bottom left corner of the top flap. Next, fold down the top 2 corners of the bottom flap.

Each fold angle should be 1 3 of the flap length.

Fold the tips of the corners to make them more like wheels. The horns you just folded will be made into wheels. Please fold the tips of the corners down to flatten them, which is more like a wheel.

You can also do this by cutting the corners into semicircles. Fold the entire sheet in half along the first crease. This is the way to complete the body of the car, make sure you want the color on the outside.

Make sure to move your nails back and forth over the top crease so that the marks are visible.

Fold the top right corner inward. Gently hold the car with your left hand. Press down on the right side of the crease until it enters the car.

Flatten the car and use your fingernails to make a crease along the edges. Fold the upper left corner inward to make the windshield. This time, fold the pocket at a small angle so that it extends beyond the front wheel.

Draw the doors and windows with a pen, and the three-dimensional car is complete.

The paper car is made as follows:

1. The material of the paper car is simple, and we only need to prepare a square colored paper.

2. Fold the top edge of the square downwards.

3. Fold both sides outward, the outermost layer, and then fold it.

4. The upper left corner and the upper right corner are folded down from the inside, and the small pointed point exposed represents the wheel, and the upper edge represents the roof.

5. Fold the two small tips below into a short section from the inside and fold them flat.

6. Draw the window of the car with a pen, and the children's car is ready.

The method of paper car is not complicated, easy to use, interested parents and children according to the above method, you can try to make a simple origami car by yourself.

Benefits of Origami Games:

1. Origami can improve children's hands-on ability, attention and thinking ability.

In this kind of art and handicraft activities, children's thinking, memory, and concentration can be fully improved. Cultivating and training children's good attention from an early age will have a positive impact on children's learning efficiency in the future.

2. Cultivate and improve children's self-confidence.

Children will have a strong sense of accomplishment after folding a form, praise for parents and teachers, can enhance children's self-confidence, so that children's lives are enriched, children will be more confident and full of wisdom, and all aspects can be full of charm in the future.

How to make a toy car from paper:

Tools Raw Materials:

The carton is sufficient, it is better to flatten it and two wooden sticks (car beams).

Appropriate amount of super glue and tape.

Scissors, red pens, etc.

Method Steps:

Glue the parts well, this is the main body of the car.

The coloring, trimming, lights, and windows are all complete.

To make wheels, the rim is black, black tape is OK, painting is OK, in short, it must be realistic.

Thread both wheels with wooden sticks and fix the wheels to the bottom of the car.

It depends on what kind of paper you want to do, it can be paper spreading, corrugated paper, and paper molds, Hebitang has paper and car paper molds, how to do this, as long as there is a sample drawing, it is not difficult to do, I hope to adopt.

Make the simplest car out of a cardboard box, and you can finally run after a busy day.

[Toy car] [Preparation materials]:

Hot melt glue gun, cardboard, tissue tube, mineral water lid, cotton swab, scissors.

Children should pay attention to safety when using scissors) 1. Take out a paper tube, apply glue around the paper tube, and then glue the cardboard to the paper tube.

2. Take out the cotton swab, remove the two ends of the cotton, leave only the middle part of the bamboo stick, roll up the bamboo skewer with cardboard, and then draw out the bamboo skewer, leaving only the cardboard rolled into a bamboo skewer.

3. Take out the hot-melt glue gun, apply glue in the middle of the internal test of the mineral water bottle cap, then glue the bamboo skewer to the mineral water bottle cap, put the finished cardboard paper into the bamboo skewer, and glue another mineral water bottle cap on the other end of the bamboo skewer.

4. Apply glue to the bamboo stick cardboard and glue the paper tube we have prepared. Since the car has four wheels, we can repeat the above method to get the other two wheels

The little toy car is ready!

1. Prepare a piece of paper, the length of which should be more than twice the width, such as the length and width of the banknote. The first step is to fold it in half from the middle.

2. Fold out triangles on both sides.

3. Fold it again on the basis of the above figure.

4. After opening the origami paper in the above picture, fold it in half in the middle according to the two sides of the crease paper in the above picture.

5. Fold both sides of the paper into it.

6. For the sake of visualization, this is the shape of the above diagram in reverse.

7. Fold the paper as shown above, in fact, it is put away according to the creases, and both sides are the same.

8. Now use one of the sides as a demonstration, and first fold the triangles on both sides to the top corner.

9. Put down the triangle folded in the picture above and turn it into two squares.

10. Fold the two adjacent sides of the two small squares against the middle line, and fold them on both sides.

11. Pressing down the folded shape of the above picture becomes this effect.

12. After both sides are folded according to the above step gear, this is the effect of the picture.

14. The extra tail is folded in like the picture in order to fix both sides of this heart, otherwise it will open. If you want to use it as a bookmark, you can also choose a paper that is twice as long as it is wide, so that there is no superfluity.

15. The final product is origami.