The FCD 25A13 indicator is not lit

The external wires are not properly connected, and the electricity is not coming in.

The electric water heater has a problem with the quality or internal aging.

The air switch is of poor quality or is not switched on.

The wire is not connected properly, sometimes when the wire is connected, the wire is stuffed hard in order to be reliable, and then the pressure sheet of the air switch is only pressed on the rubber of the wire, and the wire is not pressed to the point that the machine is not energized.

Samsung Electronics' research and experiments have shown that it has succeeded in transmitting data within a range of 2 km at a speed of more than 1 gigabit per second in the ultra-high frequency band of 28 GHz. Previously, no company or institution in the world has developed a data transmission technology that achieves more than gigabytes per second in the ultra-high frequency band above 6GHz, because it is difficult to solve the problems caused by the large data loss and short transmission distance caused by the ultra-high frequency wavelength band.

Samsung Electronics uses adaptive array transmission technology with 64 antenna units to enable long-distance transmission of radio waves, and can track the location of user terminals in real time to realize the optimal exchange of data. The success of UHBAND data transmission technology not only ensures higher data transmission speed, but also effectively solves the mobile communication band.

Dear, I'm glad to answer for you.

Hello dear! You can see if the air switch for the water heater jumps on, if it doesn't jump and a little, then Songwu recommends that you call 400-618-7777 to repair a sock, and let a professional master check the machine for you.

If there is a short circuit, first of all, the leakage light will not be on, the heating indicator is not on, you first check whether the thermostat is damaged, the thermostat is broken, the indicator light is not on, and it will not be heated, and then check whether the circuit is open.

Reason 1: The power socket plugged into the water heater may be out of power, so you can unplug it and test it with a voltage tester. Reason 2:

If the thermostat of the electric water heater is faulty or damaged, it will also cause the electric water heater to not be energized, so that it does not light up and does not heat, and a thermostat needs to be replaced. Reason 3: Damage to the thermostat will also cause such failures, which need to be repaired in time.

Hello! The real cause of the failure should be caused by the abnormal temperature control circuit or heating circuit, this kind of problem cannot be solved by itself, and can only be solved by contacting after-sales or home appliance maintenance personnel to help.

First of all, you should check whether there is a poor contact between the power socket and the plug, which is generally caused by this fault. If the contact is poor, the multimeter should be used to measure the resistance between the power cord plug L live wire and the N zero line, if the meter needle swings, it is generally normal, if it does not swing, the side cover of the water tank should be opened to check whether the power cord and each connector have poor contact, and measure whether the power cord connector and the power cord plug in the side cover are on, whether the temperature switch and the electric heating tube are normal, and check and eliminate the fault in turn.

I can't remember if it's a dry boil or a wiring problem, so I recommend checking the wiring first, and then confirming whether the water in the inner tank is full. Turn it on again and try it out.

Hello, thank you for asking the company.

When the temperature reaches the right and the knob is also turned to the highest temperature position, it means that the temperature has been heated to the highest value set, and the two switch indicators are off at this time, indicating that the heating is completed, and the indicator light will be on if the heating switch is restarted, and the role of this switch is also the on/off of the circuit, if it is in a closed state, the water heater will not heat up, and the light will not be on.

You are welcome to ask the company questions again.

We wish you a happy work life

What is the difference between the two switches?

After plugging in the power supply, turn the white concave dot on the knob to the position at max, at this time, you can select the power required for heating by pressing the yellow (800W heating) and red (1200W heating) button (this is the power on/off key) at the right end of the cover: press one end of the yellow button, and the yellow indicator light will light up, indicating that the 800W heating tube is selected for heating; Press one end on the red button, and the red indicator light will light up, indicating that the 1200W heating tube is selected for heating; If one end of the two buttons is pressed at the same time, the yellow and red indicators are lit at the same time, indicating that the 800W and 1200W heating tubes are heated at the same time.

I'm also sick with this, is it broken?

Dear, I'm glad to answer for you.

Hello dear! E1 is generally caused by dry burning caused by insufficient water in the machine, you can call 400-618-7777 to report for repair, and the customer service staff will arrange for you to test it.

Dear, I'm glad to answer for you.

The rated pressure required by this water heater is that when installing, please pay attention to whether the water is in line with the requirements.

Electrical appliances have nothing to do with water pressure, there is a relationship, the sail is the water flow of your home itself... If there is no water pressure in the water pipe, nothing will work, and it will be good to install a booster pump.