Want to know, can a self built house in the countryside install a real fire fireplace?

*OK**. Self-built houses in rural areas can be equipped with real fire fireplaces. A real fire fireplace is an efficient and environmentally friendly way to heat a house in the countryside.

It can achieve the heating effect through heat radiation conduction and convection, and the thermal effect can be felt within a few minutes, and the heat radiation generated by combustion is good for the body, and has the effect of dehumidification. In addition, the real fire fireplace also has the advantages of health, low cost of use, warmth and romance, and makes life moody. However, when installing a real fire fireplace, you need to consider factors such as the structure of the house, local fire regulations, etc., so you need to consult a professional installer and relevant departments.

Of course, I have installed biomass pellets from Yongheng Yiwei.

A real fireplace, this kind of fireplace not only has excellent thermal performance to keep the interior dry and warm, but this fireplace is also very healthy, comfortable, safe and beautiful. Glad mine was helpful to you, thank you.

It is very dangerous to install real fire fireplaces in self-built houses in rural areas in the north, and it is necessary to start from two aspects.

First, the real fire wall-hung stove is easy to cause disasters, and children at home are easy to be burned, and the house is now full of modern furniture, which is easy to be used and the dust is relatively large.

Second, polluting the environment, burning fires is now prohibited in rural areas in the north, natural gas is used for heating and cooking, and fires are no longer used for the sake of the environment of the homeland.

Therefore, it is recommended that you do not use a real fireplace, but can install a fake decoration.

Rural self-built houses can be installed with real fire fireplaces, and professional construction teams are invited to construct and pass the security inspection of the fire department. Rural self-built houses are allowed to install real fire fireplaces, as long as the quality is up to standard and safety measures are in place Real fire fireplaces are still practical and beautiful.

with refractory bricks. and refractory cement masonry. The furnace door should be made of cast iron. If you want to watch the fire well, use the cast iron furnace door frame, and the frame is inlaid with glass, but pay attention to the fireplace to use imported high-temperature resistant glass. Two dampers (preferably cast iron) are installed under the furnace door.

Install a cast iron heat sink above the furnace chamber.

Otherwise, the heat will be pulled outside. Finally, the chimney must reach 4 meters. (Cast iron heat sink above the furnace is very important) The reason why cast iron materials are used is because they are durable and can be used for a lifetime.

If you really don't want to use it, you can also dismantle it and sell it for scrap metal. Determine the style of decoration according to your own preferences, and then consider the smoke exhaust of the fireplace.

(Fireplace masonry method) with refractory bricks and refractory cement. The furnace door should be made of cast iron. If you want to watch the fire effect, you should use the door frame of the cast iron furnace, and the frame should be inlaid with glass, but it should be noted that the fireplace should use imported high-temperature resistant glass.

Two dampers (preferably cast iron) are installed under the furnace door. Install a cast iron heat sink above the furnace chamber, otherwise the heat will be pulled outside. Finally, the chimney must reach 4 meters.

The cast iron heat sink above the furnace is very important) only so the cast iron material is used because it is durable and can be used for a lifetime. If you really don't want to use it, you can also dismantle it and sell it for scrap metal.

Heating fireplaces, which have the same life as buildings, have their own unique design and do not use cast iron to dissipate heat. is thermal radiant heating, infrared.

It's not realistic to build it yourself, so ask a professional construction designer. It doesn't cost much - a little more expensive than buying an iron stove, but not much. The effect is more than several times worse.

Because the fireplace burns needs enough oxygen, the entry of oxygen requires the chimney to have enough pumping force, that is, the wind pulling force, the size of the pumping force is directly related to the height of the chimney, generally speaking, the vertical height should be greater than 5 meters, otherwise the combustion chamber will pour back smoke and burn cleanly.

The chimney must use a metal pipe of appropriate caliber, the surface of the brick is too rough and easy to collect soot, it is not used for a few years to block, and the 90-degree right-angle turn is used to affect the pumping force and is inconvenient to pass the chimney in the future, please use a 45-degree angle upward.

In addition, the installation of outdoor cigarette caps must also be transparent without obstructions, and the length, width and height of the furnace chamber are also proportional.

Materials: a certain amount of bricks, billets, stones, thin mud, cement, insulation soil.

1. Use red bricks on the ground to build a supporting column base.

2. Build a smoke guide groove at the chimney mouth of the wall.

3. Lay a refractory insulation layer in the kang.

4. Splice the prefabricated kang board on the column base.

5. Smooth the kang surface with cement and fine sand mud.

6. Burn straw and other kang surfaces in the stove to dry.

7. Spread the kang leather to sleep people.

There are more of these in Western countries. "Usually the installation of fireplaces should be determined according to the structure of the house itself, for modern fireplaces, there are generally two types, one is the steel structure of the fireplace, which is generally mass-produced by the factory, and the other is the brick and stone fireplace, which is made by hand. Steel fireplaces are more common at present, and they are easy to install, and the installer only needs to discharge this fireplace directly to the reserved position in the room, and this kind of fireplace will not cause the burning of nearby objects because of its overheating appearance.

At the same time, the product also has good after-sales service. "I hope my answer helps.

The key points of making a fireplace: the furnace material should be insulated and refractory, there should be ventilation and ash removal port below, the top of the flue should be rainproof and have a wire mesh shield to prevent foreign matter, and when not in use, it should be able to cover the guard plate and seal, and then the top of the furnace should be set up on both sides of the protrusion part to set aside the iron bar to hang the bacon. \x0d\x0a1.

Kiss, <>

We're glad to answer your questions! Rural self-built houses for fireplaces Determine the construction location and build the fireplace foundation with hollow bricks: After filling and leveling the foundation with cement mortar, build the furnace wall and hearth on the foundation, because the fireplace itself has a certain height, the hollow bricks are supported by steel bars to ensure its stability.

The function of laying refractory bricks and refractory coatings in the furnace is to ensure that the fuel is burned as much as possible, and to cool the temperature of the flue gas at the outlet of the furnace to the temperature allowed for the safe operation of the convection heating surface, for this purpose, the furnace should have enough space and arrange enough heating surface; In addition, there should be a reasonable shape and size, so as to facilitate the cooperation with the burner, organize the aerodynamic field in the furnace, so that the flame does not adhere to the wall, does not rush to the wall, has a high degree of filling, and the wall heat load is uniform. In the furnace according to the height of the furnace mouth, build a lintel to expand the data 1, the fireplace as a whole can be built with refractory bricks and refractory cement. It is necessary to choose good materials, to insulate and refractory, and to take into account the problem of outdoor exhaust chimneys.

It is recommended to build with refractory bricks and refractory cement. 2. The furnace door should be made of cast iron. If you want to watch the fire well, then you should use the door frame of the cast iron furnace, and the frame should also be inlaid with glass, but it should be noted that the fireplace should use some imported high-temperature resistant glass.

3. Install two dampers under the furnace door (preferably cast iron). Install a cast iron heat sink above the furnace chamber, otherwise the heat will be pulled outside. Hope mine can help you!

Notes:1Maintain tightness;

2。The gas outlet channel is designed to ensure that the heat is left in the furnace body before the flue gas is discharged;

3。It should be noted that the connection between the heating part and the furnace wall needs to consider the thermal expansion and cold contraction;

4。Regular maintenance, the fireplace is a durable facility, maintenance does not need to be difficult, once every 10 years;

5。Design a small door for maintenance.

6。When you need to heat at night, you need to advance to the afternoon**, and the amount of firewood used for a single room is 20 catties, which can be maintained until the next day. If you use coal, the amount is less.

I have drawings.