I want to buy a photocopier 10, I want to buy a photocopier

I used to do typing and copying agencies, I did it for more than four years, and the old photocopiers were used two, and finally I bought a new one, you had better just buy a copy function, and I don't want to print a fax scanning all-in-one machine, because there are a lot of problems with that kind of type, you are a typing and copying company must scanner fax machine printers have been separated, so don't buy a photocopier so complicated, the probability of a complex machine is also high! You go to the technology market and Jiefang Road to see more, you can bargain hard, I buy a new Kyocera machine is not bad, but I buy a few days later than a friend and spend more than 800? At that time, I also bargained, thinking that it might be about the same, but later I realized that it was too expensive!

In short, you just need to pick and choose and see more!

Aurora launched 2Non-stop service, that is: response within 2 minutes, four working hours to repair, 8 working hours to solve the problem, free from your worries. Aurora products are your ideal office partner.

Tianjin I know people who make second-hand copiers and new machines, I am a wholesale photocopier in Beijing, and you can contact whoever you want.

It is recommended that you go and buy a multi-function machine!

I don't know if you're a friend, I have more than 800 HP's multi-function machines here, which are all-in-one printers, copiers, and scanners, which are very good, you can consider it!

Today's printers generally have the function of printing and copying, as follows.

How to use the printer:

1. Copying: Open the upper cover of the photocopier, put the side to be copied downward, the paper head facing right, put it on the lower right corner of the glass plate, and close the lid.

2. Set the number of copies to print as needed, adjust the light and depth, and press "Start Copying".

3. Print: Click "Preview File" to see if the printing meets the requirements, click the "File" menu when printing, click "Print", set the required printing page range on the left side of the pop-up window, set the number of copies on the right side, and click "OK" at the bottom of the window to start printing.

4. When printing on both sides, take out the printed paper according to the prompts, the blank side is up, the head is facing inward, and then put it in the paper place, click the pop-up window "OK".

The photocopier can print. Although the photocopier is an extension function of the multifunction machine, it can be used as a printer, and it is completely consistent with the printer in terms of printing speed, printing quality, paper processing capacity, and printing function.

A photocopier refers to an electrostatic photocopier, which is a device that uses electrostatic technology to copy documents. The photocopier is an analog method and can only be used to make truthful copies of documents. Digital photocopiers will make it possible to store, transmit, and typeset images (image composition, addition or deletion of information, partial enlargement or reduction, and correction of errors).

It can be connected to computers, word processors, and other microprocessors through interfaces, and becomes an important part of the regional network. Multi-functional, colorful, inexpensive and miniaturized, and high-speed are still important development directions.

A photocopier is a device that obtains an equal, enlarged, or reduced copy of an original that is written, drawn, or printed. The main difference between the photocopier and the traditional lead printing, wax paper mimeographing, offset printing, etc. is that there is no need to go through other intermediate means such as plate making, and the photocopy can be obtained directly from the original. It is more economical to make small copies.

Summary. 1.Turn on the copy device. Generally, there is a switch button in the lower right corner of the photocopier equipment, press the button to start the photocopier equipment.

2.Check the photocopying equipment. Check whether there is paper in the paper tray of the copier's equipment, whether there is a shortage of paper, etc.

3.Check the copied manuscript. Check whether the manuscript to be copied has staples, distinguishing pins, etc., and if so, order them.

4.Place the copied manuscript. Open the upper cover of the copier, there is an indicator sign or a scale indicator on the flat glass, refer to this indicator to put the manuscript to be copied into it, and put down the file cover.

It can also be placed on rollers, which is suitable for copying large batches of documents without the need to place documents back and forth.

5.Sets the score for copying. Click "Copy" on the control panel of the copier, then enter the copying setting interface, press the left and right arrows to set the number of copies to be copied, or press the "+" button to set.

6.Select the type you want to copy. If you want to copy the manuscript in black and white or color, click the relevant button to complete the copying.

I bought a copy printer, is there a tutorial?

Hello, I have seen your question and am sorting out the answer, please wait a while

1.Turn on the copy device. Generally, there is a switch button in the lower right corner of the photocopier equipment, and the button is pressed to start the photocopier equipment.

2.Check the photocopying equipment. Check whether there is paper in the potato paper tray of the copier's equipment, whether there is a shortage of paper, etc.

3.Check the copied manuscript. Check whether the manuscript to be copied has a staple mold, a distinguishing needle, etc., and if so, order it.

4.Place the copied manuscript. Open the upper cover of the copier, there is an indicator sign or a scale indicator on the flat glass, refer to this indicator to put the manuscript to be copied into it, and put down the file cover.

It can also be placed on rollers, which is suitable for copying large batches of documents without the need to place documents back and forth. 5.Sets the score for copying.

Click "Copy" on the control panel of the copier, then enter the copying setting interface, press the left and right arrows to set the number of copies to be copied, or press the "+" button to set. 6.Select the type you want to copy.

If you want to copy the manuscript in black and white or color, click the relevant button to complete the copying.

OK. Although the photocopier is an extension function of the multifunction machine, it can be used as a printer, and it is completely consistent with the printer in terms of printing speed, printing quality, paper processing capacity, and printing function, and is even better than ordinary printers in terms of printing load and single page printing cost.

Moreover, it has maintained the same technology as the printer field in terms of confidential printing, storage printing, and network printing, and even in the development trend of color, the digital multifunction machine has kept pace with the printer field, and there seems to be no reason to exclude it from the printing field.