Can the socket plug be repaired if it is broken, and how to repair the socket if it burns

If you have a certain amount of hands-on ability, of course you can fix it. Now the plugs of household appliances are molded and disposable, usually the wire at the root of the plug is broken, which is generally not easy to repair, and requires certain skills, cut the plug and weld the wire again, close the plug and wrap it with adhesive tape.

The socket is generally internally disconnected, and the spring sheet is deformed and the contact is poor, as long as the broken wire is connected (welded) well, the spring sheet can be repaired with needle-nose pliers.

Not necessarily. It depends on which position of your plug is broken, so you can decide whether it can be repaired or not. Generally, the kind of hardware store can buy a socket, so let's buy one directly.

Because even if it can be repaired, it is very troublesome. You may have to send it back to the manufacturer, and then the manufacturer will have to open it before you can find the part of the problem. If there are no parts, or the value of the parts is low, they may no longer be produced, and then they cannot be repaired.

Depending on the damage, the key is your ability.

There is nothing that cannot be repaired in our maintenance, the key is to see whether the thing is valuable, and we need to repair it before we consider whether to repair it.

Disconnect the power supply and pry the cover of the outlet open. Here's how to replace the wall outlet.

1. Close the main electric valve in the room, which can prevent electric shock accidents during construction.

2. Take a flathead screwdriver to pry the cover of the socket open, and then disassemble it.

3. Take the meter to detect whether the circuit is live, and after ensuring safety, unscrew the reinforced screws.

4. Connect the prepared new socket and finally cover the cover.

How to repair a burned wall socket

1. First close the switch switch to prevent electric shock.

2. Secondly, open the socket box, unscrew the fixing screw with a Phillips screwdriver, and turn it left and right if the screw is difficult to remove.

3. Then use a screwdriver to remove each wiring one by one.

4. Finally, replace the new socket and wire it according to the principle of the ground wire above the left zero wire and the right live wire. No problem with the test trial. Then tighten the set screws and close the socket box lid.

Causes and solutions for wall sockets to run out of power

1. Tripping or short circuit.

If the other circuits in the home are normal and only the socket is out of power, it is likely to be caused by a trip or short circuit. Loose overlapping wires in the socket, falling screws, short circuits in the reeds, or water and energizing the socket will cause a short circuit, resulting in no power to the wall socket.

Solution: First of all, you can check whether the air switch of the control socket has tripped, if there is a trip, it means that the circuit is overloaded or short-circuited, and the air switch can be closed directly. If it continues to trip after closing, you need to ask a professional electrician to overhaul the line.

2. Poor contact.

The circuit connection is not smooth, which will naturally lead to no power in the socket, and there are two most common situations of poor contact of the wall socket: first, the connection wire head between the air switch and the socket will fall off or oxidize; The second is that the connecting screw of the thread is not tightened.

Solution: Disassemble the control panel of the wall socket, find the unreachable position, and then reconnect it firmly. Aging wires or parts that need to be replaced should also be disposed of.

3. The line is broken.

The socket generally has three or two wires, namely the live wire, the neutral wire, and the ground wire, of which the live wire and the neutral wire are the lines that the switch must be connected, and one of them will cause the socket to run out of power.

Solution: Use a pen to detect the socket current, if the 2 empty neon bubbles are lit, the neutral line is broken, if the 2 empty neon bubbles are not lit, the live wire is broken. The solution to the line disconnection is very simple, direct wiring can be done, but this operation needs to be handled by a professional electrician who is familiar with the circuit, and you should not connect it casually.

It is recommended to buy a corresponding socket and then find a professional electrician to deal with it, which involves professional knowledge, and do not do it easily by yourself or non-professionals.

Repair method: 1. Pry open from the side of the switch panel and take off the panel;

2. There are two fixed screws, remove them one by one;

3. In the case of ensuring power failure, carefully take out the built-in junction box of the socket;

4. Mark according to the original position and remove the wires;

5. Adjust the direction of the new socket you want to replace with according to the way of use, and connect the wires one by one according to the wiring method identified;

6. Put the socket in its original position, align the mounting holes of the screws, put on the screws, and cover the panel.

First disconnect the electricity, and then disassemble the inside to observe is the best problem, if it is just disconnected and connected, if it is the circuit aging, etc., it has to be renovated.

The socket burned out, and the circuit needs to be disconnected in time and the plug on the socket needs to be unplugged. Then check the socket with screws to disassemble to see if there is a wire disconnection inside, if it is disconnected, the line needs to be soldered. If it is difficult to repair, you can only discard it and buy a new socket to use.

Introduction to the socket

Sockets. That is, it is a multi-position socket with wire, commonly known as a power strip.

Power strips, scientific name wire extension assemblies or extension cord sockets. A strip is a multi-position outlet with a power cord and plug that can be moved. More than one power plug can be connected, saving both space and lines.

Because of its convenience and energy saving, the smart switch socket has been widely welcomed by foreign consumers, and the smart switch socket is becoming a research hotspot for new energy-saving products.

Appearance. The surface is smooth and smooth, the color is uniform, and the texture is generally a good product. In addition, the brand logo on the panel should be clear and full, without any burrs on the surface.

The lower part is welded, and the upper part is a one-piece core.

3. Internal structure. The ordinary strip plug is a welded structure, and the more advanced one core structure is a one-piece core structure.

Feel. Try the switch, a good switch spring is moderately soft and hard, the elasticity is excellent, and the turning point of opening and closing is relatively strong. There is no such thing as a strip button stopping somewhere in the middle and becoming a serious fire hazard.

It can also be plugged in, and high-quality products will not have a light feeling because of the large use of copper and silver metal.

The socket burned and repaired and replacedThe steps are as follows:

Tools: safety socket, screwdriver, electric pen.

1. Nai Sheng first went to a nearby hardware store to buy a safety socket of the same specification and model, pulled off the damaged socket branch switch in the indoor distribution box, and disconnected the damaged socket power supply.

2. Use a screwdriver to remove the socket cover from the side of the damaged socket, remove the 2 screws that fix the socket counterclockwise, pull out the damaged socket, remove the screws that fix the wires counterclockwise, and remove the damaged socket.

3. Use a screwdriver to remove the socket grip section cover from the side of the new socket, loosen the screws that fix the wires counterclockwise, and tighten the screws clockwise one by one on the corresponding socket of the live wire (yellow line or Duan Mu Yu green or red), zero wire (blue), and ground wire (yellow and green color).

4. Push up the socket branch switch of the indoor distribution box, test whether the voltage of the new socket is normal with a pen, if it is normal, push the new socket into the junction box, tighten the 2 screws that fix the socket clockwise, and then buckle the new socket cover.

5. If the voltage of the new socket is abnormal, re-check and fix the live wire, neutral wire and ground wire, if the voltage is still abnormal, you need to hire a professional electrician to check the power line.

1. Go to the hardware store first and buy a new plug.

2. Then cut off the head and cut the wire with a wire trimmer

3. Connect the wire to the new plug.

How to repair the broken root of the wire plugHere are some tips to fix a broken power plug:

First of all, the root of the wire plug must be dealt with in time, otherwise it is easy to short-circuit and burn out the electrical appliances, if the wire skin is rotten, you must first wrap the two wires inside the wire with insulating tape, so that the two wires are kept in an isolated state to avoid accidents caused by short circuits.

The second step, then we prepare two cable ties, tie the cable ties to the two ends of the wire break, and finally use scissors to cut off the excess cable ties, the cable ties play a fixed role to prevent the wires from pulling and breaking.

The third step and the last step are to roll a few more layers of insulating tape to repair the broken power plug.