What should I do if the five pin socket is loose and the plug is in poor contact?

The copper sheet inside the socket is loose, and the best thing to do is to change it a little bit. If you are reluctant to repair such as clamping and the like, it will be enough, because the elasticity of the copper sheet has deteriorated.

What should I do if the five-pin socket is loose and the plug is in poor contact? The best way to "replace" a new outlet!

Correct practice, it should be turned off, and the main power supply should be removed with a screwdriver. I pinch the steel sheet which I sent tightly. Or tighten the loose screws. After repairing. Put on the panel and then send power. It's solved.

The five-hole socket is loose, if you want to repair it, first cut off the power supply, and then unscrew the screws on both sides.

In this case, it is best to replace the new socket is the most reliable, the socket has been loose, the contact is poor, even if it is disassembled and adjusted, it can not achieve the ideal effect, or replace it as soon as possible to avoid future troubles.

If the plug is loose, it means that the quality of the components inside is not good, don't think about repairing, it is best to replace the socket with a new one, after all, safety first. The five-pin socket I used at home has been good for more than ten years and has not been loosened.

You can disconnect the power supply, find a cone to open the socket panel, and tighten the internal wiring.

In this case. You should find a professional. Carry out repairs.

Poor plug contact. It is possible that it is overloaded. It is recommended to replace it with a new one.

If the plug is not used frequently. Repair it, and you can continue to use it. Powerful loads.

It is recommended to replace it immediately. Eliminate potential safety hazards.

Spend money to find a master electrician to replace the socket.

Since that's the case, I usually replace the restart button with a power switch, but it really doesn't work, so I connect it externally.

Change the socket The quality of the socket used for the computer should not be too bad, otherwise the computer hardware may be burned.

--- poor contact of the socket is a common phenomenon--- the solution is very simple: if it is a wall socket, use two flat screwdrivers or sharp knives, the upper and lower two places against the wall to pry out to open the shell, the two copper pieces to clamp tightly together can continue to use normally, if the piece is weak and has lost its elasticity, it can only be replaced with a new socket. Note:

Turn off the power before repairing!

Pull the plug and use it temporarily.

Take the cleaning solution to clean it and disassemble it.

Either buy a new one, or disassemble it yourself and reinstall it.

Many people think that the plug is broken if it is loose, so let's teach you how to plug the loose plug tightly?

How it works:

The reason for the loose plug may not be the plug itself, or it may be a problem with the outlet. There is a possibility that the screws of the base of the socket are loose, so check the bottom of the socket at this time. with a screwdriver.

Repair the loose parts.

It is also possible that the plug itself is caused by a loose contact surface on the plug or a position shift. At this time, the position should be corrected in time so that the plug can work normally.

The reason for the loose plug may also be the cause of the current, and the size of the current will also affect the use of the plug. If the current is too high, the temperature of the plug will be too high, and the plug will melt and loosen. At this time, the power should be turned off and the plug should be allowed to cool.

In short, when using plugs and sockets, pay attention to electrical safety, and do not operate them when there are no protective measures. Also, do not operate around the plug with too high or too low temperature, which will also affect the performance of the plug.

If the socket is not in good contact, you need to unplug the socket, then disassemble the socket, check whether the internal components are damaged, and repair it in time, so that it can be used normally. If you don't like the trouble of repairing, you can go to the market and buy a new socket, so the budget required is not too high.

3. If the copper sheet inside the socket is deformed, it will also cause it to be unable to be used normally, so it is necessary to use professional tools to restore it. In addition, when buying sockets, we must pay attention to choosing cooperation with big brands, so as not to buy sockets with quality problems, which will lead to the existence of potential safety hazards and affect home life.

It is very easy to solve, one is to repair, disassemble the socket, adjust the copper sheet inside, the plug can be plugged tightly, the second is to adjust the plug, pinch the plug to the center, and it can also be expanded, so that he can contact the plug normally, and finally simply change the socket, although it is troublesome, but the effect is the best. Pay attention to the power outage operation, do not live construction.

Then a new outlet will do.

First of all, before repairing, you should determine whether it is because of the power outage at home, some people will say that this step is redundant, but in fact it is not, there will always be people who are ready to repair, only to find that it is a power outage, but also to check whether all the sockets are out of power or only this one socket is not powered, and the circuit should be switched off and closed to ensure safety when starting to repair or replace.

A screwdriver, multimeter, and voltage tester should be prepared before the examination. Use a voltage tester to detect the circuit first, if there is power in the socket next to it, only this socket has no power, that is, there is a problem with this socket. It may be caused by poor contact of the wire in the socket or the burning or aging of the socket, and if the socket is burned and aging, it can only be replaced with a new socket.

When replacing, you need to turn off the air switch, cut off the power supply and then remove the socket with a screwdriver, loosen the screws on the binding post, and then connect the live wire to the junction post of L, connect the neutral wire to the binding post of N, and there is a two-color grounding wire, install the new socket, pay attention to the position of the neutral wire and the live wire can not be connected wrong, and after completion, you can use a universal meter to test whether it is successful.

If there is sometimes power and sometimes no power in the socket, it is possible that the wires inside the socket are loose or the copper sheet inside is loose. If the wire is loose, after the panel of the socket is opened, just tighten the screws on the binding post.

If the copper sheet is loose, the copper sheet can be clamped with pliers, and in many cases, the copper sheet of inferior products will be more likely to loosen, so when choosing, we must choose trustworthy products with better quality to reduce the occurrence of such situations.

Poor contact --- sockets is a common phenomenon.

- The solution is very simple: if it is a wall socket, use two flat screwdrivers or sharp knives, pry the upper and lower two places against the wall to open the shell, clamp the two copper sheets inward and stick tightly to continue normal use, if the piece is weak and has lost its elasticity, it can only be replaced with a new socket. Note:

Turn off the power before repairing!