What should I do if the wires buried in the wall burn out? What s the right thing to do?

How to pull out the wire and how to thread the new wire: first we have to find the joints at both ends of the wire, put it? Do you want to tear down the wall?

First of all, according to the meaning of the title, you can understand that your home is a building, and the building line concealment is to lay PVC line pipe, that is, later you decorate, you also need to lay line pipe, eliminate the case of line pipe blockage, you can clearly do not need to disassemble the wire joint and cut off the bent wire; Then wrap the wire around a large wrench at one end of the wire, and take this according to the actual situation of your building, if the wiring of the kitchen lighting in my house is broken, I draw a bright wire from the socket closest to the lamp, and string a switch brick hollow wall can be replaced in the wall. Nowadays, many places are built with solid walls.

Box master switch! Open the bathroom buried main socket cover, remove the three wires (mark the wiring position of the three wires), the wire of the measuring wire socket is 4 square millimeters of wires is not easy to burn out, even if it is burned out, you can generally change the line, this specific need to find an electrician to go to your home site to see if you can change the line or think of other ways, if it is in Chengdu I can show you the diameter and estimate the length of the wire from the main socket to the household switch box, and then according to the measurement data to the electromechanical market to buy and the original do not need to tear down the wall, find out the burned out of the lineIf the wire pipe is damaged, only reopen the Cao wiring and restore the original burned out of the line!

When is your home renovated or built after 2000 years of home is generally able to pull out the line, if you can't pull out or the wall is an iron wire pipe, then take the open wire joint in the ceiling can do the surface installation of the trunking, remember to deal with the place that is easy to enter the water. I also replaced the circuit breaker of the circuit of the burned wire, and it is estimated that it is broken. Normally, he should trip to the inside, the plug board is far away from the shower area, the position is slightly higher, the open pipe modification or trunking modification is also very beautiful, and it is convenient to change the line or install the branch switch electrical appliances in the future.

1. Turn off the power. The practice should be to find a professional master to overhaul the wires at home, because the buried wires are not like the open wires, and it is easier to find that there is a problem.

First of all, you should determine whether the wall is a load-bearing wall, if it is not a load-bearing wall, first determine which part of the wire is burned, and then carry out a small area of smashing and changing the wire.

After being burned out, first check which position of the socket or electrical appliance in the home is not properly powered, determine the place where the power supply of the problem line is cut off, and notify the maintenance personnel for repair.

Summary. Hello, when we find that the wires buried in the wall are damaged, the first way to deal with them should be to replace the wires, do not take any luck to continue to use, otherwise sooner or later there will be problems, the wires buried in the wall are burned out and what will happen if you don't deal with it.

What happens if the wires buried in the wall burn out and are energized if they are not treated.

Hello, when we find that the wires buried in the wall are damaged, the first way to deal with them should be to replace the wires, and don't take any luck to continue to use the sails, otherwise sooner or later there will be problems, leakage.

Please replace it as soon as possible.

Don't replace it first, use it for a day or two.

My wire was burned out from high voltage.

It's best to replace it as soon as possible.

Burn out is also bad.

Will it be a big problem if you don't deal with it and continue to use it.

Yes. What happens if you don't replace it and continue to use it.

Seriously, my family isn't home and I won't handle it.

There is a risk of electric shock!

You can talk to your family.

Let them arrange for workers to make repairs.

Nowadays, there are more electrical appliances at home, sometimes because of excessive power burned circuit, if the home is a dark line, many people think that the burned line is going to smash the wall for maintenance, in fact, since the dark line dares to design like this, must have thought about how to repair the broken, so today the master teaches you 2 tricks, no need to remove the wall, you can easily solve the solution.

Method 1: When there is any fault in the line, the first way we think of is to replace the new wire, and don't take any chance to deal with it, so that sooner or later there will be problems.

Some friends said that this is buried in the wall, the wire can not be pumped out, the wall needs to be removed to repair, in fact, there is no need at all, generally in accordance with the strict requirements of the electrician layout of the line, are can be pumped out, if the wire can not be pumped out, it means that the line is not connected by professionals, or there is no pipe at all, directly deal with the buried in the concrete, this has to think of other ways.

How do I replace the wire when it is pulled out?

First of all, we need to find the joints at both ends of the wire, then disassemble the joints, use scissors to reduce the bent part, and then wrap the wire around one end of the wire on the pliers, and slowly pull it out little by little.

When wearing a new conduit, you can apply lubricating oil on the wire, and then tie the wire and the wire tightly, and use the same way to draw the wire into it, so the circuit knowledge is not a professional, and it is good to understand a little, after all, it is impossible to say that there is a little problem at home to hire an electrician.

Method 2: If you find that the previous line can't be extracted, or if you don't want to be so troublesome, you can consider the surface-mounted wire, but the surface-mounted wire will definitely affect the appearance, which needs to be taken into account.

Specific operation: choose the best point of the trunking or conduit, use structural adhesive to arrange the trunking in the direction of the trunking we designed in advance, wait until the structural adhesive reaches a certain strength, put the wire into it, and then deal with the street well, here is the explanation, the use of structural adhesive, to avoid screws in the wall when fixing the trunking.

Summary: The above two methods can be done without demolishing the wall, the first method is to use the way of drawing wire to maintain on the basis of the original, the second is to directly install the obvious, if you don't mind affecting the appearance, you can choose the second one.

Mobile phone number 18811357340

Now decoration in order to make the interior more beautiful, especially when decorating water and electricity, the pipes and wires will be hidden in the wall, but after the wires are hidden in the wall, in our future life, if the wires are burned out, it is relatively troublesome. Today, I will introduce to you the wires in the wall of the room that suddenly burned out, and the precautions for wire installation are available? Let's take a look!

1. The wires in the walls of the room suddenly burned out.

1. At the very beginning, there was no experience in installing wires, and the wires were directly laid into the cement, and then people mastered some methods, knowing that the wires were put in the protective pipe in the cement, and there were many people who did not understand or would put the wires in the cement.

2. First of all, we will close the wire into the protective pipe and hide it in the wall. According to this situation, the wire is well protected, and it will deteriorate after a long time, and fire will occur in special circumstances. Once there is a problem, you must first find the head of the protective pipe, open the aging wire inside and take it out first, and replace the new wire with it, because it is the channel section to put the new wire into the protective pipe when the bend will form a certain obstacle, but the impact is not particularly large.

3. The wires are directly buried in the wall, in this case, the design drawings must be saved, and once there is a problem, you can find the line layout according to the lines on the drawings, in this case, we need to find out the layout drawings of the electric lines used when decorating the house. At this time, drawings have done a very important role, without design drawings, you may not know what the specific layout of the wires in the home is.

2. What are the precautions for wire installation?

1. The correct way to connect.

In the process of laying out the wire, the appearance of the joint must be avoided, because the joint is very prone to a relatively large resistance, and it will also lead to the heating of the wire.

2. Choose a reasonable installation method.

In the indoor installation of wires can choose to use the open installation and concealed installation method, the surface installation is actually along the surface of the wall and ceiling and other settings, in the installation must pay more attention to the family's self-surface installation, do not squeeze the wire or fold the wire. Concealed installation is to arrange wires in some places in the wall or ceiling, and professional operators must be hired for safety concealment.