How to remove the cover on the outside of the socket

Use a small word change cone to pry the small gap on the side of the panel, and open it with a prie.

There is a small notch on the side of the socket panel (against the wall, usually left and right or top and bottom), and it is enough to gently pry it open with a flathead screwdriver. **The cover on the outside of the socket has a complete sealing edge on three sides, only there is a gap in the middle of the edge of the sealing groove below, (some may not be careless when installing, not necessarily placed underneath) This gap is left to leave the necessary elasticity when prying the panel. Please use a small cone to remove the panel by prying it at the edge of the opening.

This is the same as some of the power socket decorative panels on the wall, so please give it a try.

Here's how to remove the socket panel:

1. Turn off the power. Before installing and disassembling the socket, the power supply must be turned off, because the socket is connected to the power supply, if the power is not interrupted and operated directly, an electric shock will occur, which will make the operator dangerous, so power failure is very critical.

2. Disassemble the socket panel. Then you can disassemble the socket, and you must first see how the socket is fixed. Usually the socket is directly fixed to the wall cassette with screws, if this kind of socket is easier to disassemble, as long as the plastic nut is unscrewed off with a small screwdriver, you can separate the socket from the cassette.

The other is that the socket is fastened to the bezel of the cassette, and the screws are not visible on the surface, only the small notch on the side of the panel. When disassembling, you can use a screwdriver to pry open the upper notch, and then use a screwdriver to unscrew the screws of the socket.

3. Check whether there is a power supply. After the socket is disassembled, it is necessary to check whether there is live power, this step is essential, although the power has been turned off, but for the sake of insurance, you must use a voltage tester to detect whether the switch socket is live inside, and confirm that the socket is not charged before the next operation.

4. Disconnect. After the socket is disassembled, you can see the junction box, at this time, separate the upper wires from the wiring, and use a screwdriver to separate the wires from the terminals. After that, pull out the wire terminals, and then remove the socket from the wall.

5. Wrap the thread. After the socket is disassembled, wrap the exposed wire end with tape, and finally plug the wire into the wall to avoid accidental contact and electric shock.

The steps to remove the socket panel are as follows:

First of all, we need to open the removed wall switch and circuit breaker, then use a flathead screwdriver to the junction box to fix the wall switch cover, remove the screws, and use a Phillips-head screwdriver to unscrew the two screws in the junction box; For the switch on the upper side, a Phillips screwdriver loosens the terminal screw and pulls the wire away from the switch; The plastic wire cap is at the end of the wire.

Electrical tape wraps around each cap and wire further securely the wire tail cap, the east and west wires enter the junction box, put a solid cover plate in the junction box towel, and use the fixing screws to open the socket of the room to power the circuit breaker. At this point, the entire disassembly step of the wall switch has been completed.

Choice of outlet:

Choose a regular brand. At present, there are many domestic socket brands, at least nearly 2,000 of them, and the quality of the products produced by these brands is obviously different. In order to avoid choosing the wrong brand, you should try to choose a big brand with a good reputation.

Choose the one that looks good. The worst of the socket can also be distinguished by its appearance. The socket with uniform color distribution, no flaws, no stains, no deformation, and no rust, cracks, and corrosion traces of metal fittings is better, and it is not recommended to buy otherwise.

Select the weight-qualified one. The lighter the socket is not the better, but it has to meet certain standards. In general, the weight of the socket is very light, probably because the copper sheet is thinner.

The copper part is the core of the socket, and its weight is not thick enough, which will directly affect the conductivity. Therefore, you should choose a socket that has a lot of weight.

Choose the one that suits the occasion of use. Bedrooms, living rooms, kitchens, bathrooms and other places, due to different environments and different equipment used, they have different requirements for sockets. For example, bathrooms and kitchens with high water vapor and heavy oil smoke should choose sockets with plastic baffles to avoid oil smoke and water vapor affecting the connection of the line.

The socket cover can be removed by simply unscrewing the screws. Socket (also known as power socket, switch socket, pinyin: chāzuò, English:

Powersocket) is a socket that can be plugged into only one or more circuits, through which various wires can be inserted, and it is convenient to connect with other circuits.

The power socket is an electrical device that provides a power interface for household appliances, and it is also an electrical accessory that is widely used in residential electrical design, and it has a close relationship with people's lives.

After residents move into new homes, it is generally reported that the number of power sockets is too small and extremely inconvenient to use, causing residents to privately connect power cords and install socket wiring boards, which often cause personal electric shock and electrical fire accidents, and bring major hidden dangers to personal and property safety. Therefore, the design of power sockets is also an important basis for evaluating residential electrical design. Sockets can be divided into industrial sockets, power sockets and mobile sockets according to their uses.

There is a small hole under the socket, and you can make a socket cover by pressing the hook in the small hole with something.

Find a flat screwdriver and insert a pry from the opening at the bottom of the panel to open the panel.

The inserted lid is actually very easy to open, what does he say about this thing? He has a place that is equivalent to a hook, and if you put that place into place, you can directly collapse when you knock it.

You said that the cover of this kind of socket should be, now more people use that kind of thing, stuck that kind, first use a flathead screwdriver or a voltage tester, and pry from the middle position under the socket to open the socket panel.

There are buckles on the top and bottom, so you can just take a screwdriver or break it by hand.

The covers of various sockets are strange and varied, how can you know how to open your lid if you don't send a picture, send a picture.

Summary. How to remove the socket cover reserved on the wall: The method of disassembling the cover of the socket is to pry open the bottom of the cover with a flathead screwdriver, and if you don't take the cover, you will expose two screws, and then use a screwdriver to remove the screws, and you can open and see the wiring inside.

How to remove the socket cover reserved on the wall.

How to remove the socket cover reserved on the wall: The method of disassembling the cover of the socket is to pry open the bottom of the cover with a flathead screwdriver, and if you don't take the cover, you will expose two screws, and then use a screwdriver to remove the screws, and you can open and see the wiring inside.

1. If you can see the screws, unscrew them directly, and you can't remove the socket cover. 2. If you can't see the screws, prove that there is a cover on the socket, the cover is stuck on the socket, you only need to pick it by hand around it, you can easily remove it, if it is very tight, you can use a pen to pry it, you can remove it, you can see the screws inside, if you need to open the socket, you can unscrew the screws again. Socket installation note:

1. The installation height of the socket should be installed according to the design requirements when the design is specified; When the design is not clear, it should generally be complied with: the socket with a safety door is not less than; The socket without a safety door is not low; It is advisable to buy an outlet with a safety gate whenever possible, as there is not much difference between the two**. 2. In the toilet or other humid places, a well-sealed waterproof and splash-proof socket should be used.

Note: The socket with a safety door is a plastic baffle (safety door) in front of the jack metal reed added to the general socket. Three-hole socket, when the plug is inserted, the grounding pile head (slightly longer) is inserted into the hole first, and the mechanism in the socket opens the other two hole doors, and the two-hole socket must be inserted into the socket pile head at the same time, and the safety door can be opened, so as to prevent young children from inserting metal objects by mistake and causing safety accidents.

3. When the socket is installed, its panel should be upright and close to the wall. Moreover, the wiring (phase) should conform to: single-phase two-hole socket, facing the right hole or upper hole of the socket to connect the phase wire (live wire); The left hole or the lower hole is connected to the zero line; Single-phase three-pin socket, facing the right hole of the socket is connected to the phase wire (L, live wire), the left hole is connected to the neutral wire (N), and the upper hole is connected to the ground wire (PE).

According to Qeeka Home experts, the socket is used to connect the interface of various electrical appliances, and it is a necessary electrical equipment for every household. So, how do you remove the socket cover? What are the tips for choosing an outlet?

Let's take a brief look at it together.

1. How to remove the socket cover.

If there are screws on the upper surface of the socket cover, loosen the screws directly, and the cover of the socket can be removed. However, if there are no screws on the socket cover, you need to use a flathead screwdriver to pry up the four corners, and then you can see the screws fixed inside, and finally use a screwdriver to loosen the screws, and the socket cover can be removed.

Second, what are the skills for choosing sockets.

1. Look at the brand: According to the survey, there are thousands of large and small socket brands on the market, and it seems that there is no gap, but in fact, the quality of niche brands is far from that of well-known brands.

2. Check the appearance: When buying the socket, you must pay attention to the appearance of the socket, including whether the color is uniform, whether the edge is burr, if there are obvious cracks, dents or burrs on the surface of the socket, you must not buy it, because a good brand, all details will be paid special attention to.

3. Weight: Because the connection point of the socket is copper, the socket is thicker, but if it is a socket of poor quality, the merchant will use a thin copper sheet in order to save costs, so that the overall weight will be much lighter.

4. Distinguish the place: there are many particulars about the purchase of sockets, different uses and places, you should choose the right socket to ensure reliable and safe operation, such as toilets and sockets, because the distance to the water source is relatively close, the air humidity is large, so you should choose the socket of the splash-proof water box.

Summary: The above about how to take off the socket cover, and what are the tips for choosing the socket are introduced here, I hope it will help you. If you want to know more about related information, please pay attention to Qeeka Home.