How to remove the spinning mop dehydration basket

Tools Required: Pliers.

Screwdriver. 1. First, loosen the middle part of the mop handle with your hands.

2. Then pull down the lid of the middle knob.

3. Then pull down the white bolt on the inner layer, and you can see the middle seam and indirect seam.

4. Then use both hands to pull the upper and lower mop levers apart. The leak knob is in the middle.

5. Remove the upper mop lever. Only the mop rod, screw rod and spacer below remained.

6. After that, remove the screw rod.

7. Remove the screw rod spacer from the mop rod.

8. After that, use a new screw rod gasket to replace it.

First remove the waterproof ring on the edge of the outside.

Then there is the fixed glue head in the water throwing blue.

Then pull the water basket out.

This kind of operation is quite laborious, and it may not be able to pull out if you have little effort.

The rotary mop is a new type of mop, which can overcome the shortcomings of all mops in the past, and is light and easy to take, easy to clean, hands are completely dirty, away from stains and sewage, and even ground debris is easy to stick; The spinning mop has super water absorption, and the spinning bucket attached to the spinning mop adopts the principle of centrifugal force, as long as you press the pedal lightly, you can quickly shake off the water. The mop head of the rotating mop is made of special microfiber, which has super water absorption performance to ensure that there are no more water stains on the mopping floor.

Probably something is wrong with the dehydration basket somewhere!

Basically, it is fixed by screws and C-type cards, which can be dismantled step by step according to the installation sequence, and the rotating part is maintained with some oil.

I believe everyone must have noticed that it can help us drain the wet mop, and with this tool we don't have to press the mop very hard. Although the mop rotating bucket is very convenient and can reduce our cleaning burden, we also need to clean it regularly, otherwise the stains remaining in the rotating bucket can easily breed bacteria. Before cleaning, we need to remove the shaft in the rotating barrel, and then we will introduce the correct disassembly method for you.

Step 1:

First we rinse the spin mop bucket and then pour the water inside the bucket clean. Press down on the bottom of the stainless steel strainer in the rotating bucket with one hand and slowly lift the other hand up from the edge of the plastic lid.

Step 2:

Then hold both sides of the lid of the plastic bucket with both hands and lift it upwards with even force.

Step 3:

Then we lift the intermediate shaft with our hands and remove the strainer together. If you can't take out the lifting shaft, you can pinch both sides of the filter with both hands and lift the filter upwards evenly.

Step 4:

After the strainer is lifted, we can clean the perimeter of the shaft and the stolen goods in the barrel separately, and then move the intermediate shaft by hand.

Step 5:

Next, after cleaning the contents of the bucket and checking the flexibility of the shaft, we cleaned the center of the strainer shaft, the dirt around the lid and all the locations. Then, align the spool in the strainer with the inner shaft of the barrel, check the flexibility of the strainer rotation, and finally close the plastic lid and press it tightly.

The above is the specific solution of how to disassemble the mop rotating barrel, I believe that everyone can quickly learn how to operate through the introduction of the above content.

Answer 3: In this way, you can pour concentrated alkaline water and soak it for some time, let the dirt react with alkali, and then scrub it with a brush, and you can wash it clean! Then rub it with a cloth and rinse it with water.

Dear hello, I hope my answer has helped you, please give us a [like] if you want, your small act is very important to us, please comment on us, your like makes us have more motivation, thank you!

The specific steps are as follows:

1. First of all, the rotating mop lever must be removed from the beginning to completely remove it. Usually, the attachment port of the mop rod is always between the mop rods. As shown in the image below, then proceed to the next step.

2. Secondly, disassemble the first part of the mop rod head, some of the mop rods are firmly connected, and it can be unscrewed with very little force, as shown in the figure below, and then move on to the next step.

3. Then, after unscrewing the mop lever, a mop will be dragged out of the mop rod to retract and release it, as shown in the figure below, and then move on to the next step.

4. Then, after loosening the extension of the mop, then directly remove and unscrew the extension of the mop as shown in the figure below, and then move on to the next step.

5. Subsequently, remove the mop head lever, and then gently rotate the mop lever a few times to remove it completely, as shown in the picture below, and then move on to the next step.

6. Finally, after disassembling the mop head lever, step on the mop head with your foot and pull the mop head firmly in order to completely disassemble the rotating mop dehydration disc, as shown in the figure below. In this way, the problem is solved.

Look at the picture and speak. First split the middle into two sections, if you want to change the mop head, there is a nut on the disc that can be rotated, spin it out, and then pull the mop head out, it's very simple! This is the pole of Qianheng's rotating mop, but it should be universal.

Rotation Mop Spinning Disc Disassembly Steps:

1. To disassemble the spinning mop dehydration disc, you must disassemble the mop rod from the Zhengzen head to completely remove it, first of all, you need to disassemble the mop rod, and the connection port of the mop rod will be in the position between the mop rods.

2. Disassemble the first section of the mop rod head, some mop rods are connected tightly, and you can unscrew it with a little force.

3. After unscrewing the mop rod, there is a mop dust burner telescopic place on the mop rod, and loosen it.

4. After loosening the telescopic part of the mop, then disassemble and unscrew the telescopic part of the mop directly.

5. Then disassemble the mop head lever, and then gently twist the mop bar a few times to completely disassemble it.

6. After disassembling the mop head rod, step on the head of the mop with your foot and pull the mop head off forcefully, so that the rotating mop dehydration disc will be completely disassembled.

1. Rinse the rotating mop bucket and pour the water in the bucket clean.

Press down on the bottom of the stainless steel strainer in the rotating bucket with one hand and slowly lift the other hand up from the edge of the plastic lid to open a gap.

This is shown in the figure below.

2. Then, hold both sides of the plastic bucket lid with both hands and lift it upwards evenly and forcefully.

This is shown in the figure below.

When lifting, you can lift your hands slowly and evenly along the perimeter of the lid and lift it upwards).

3. After the cover is lifted, lift the intermediate shaft with your hand and take off the filter screen together.

This is shown in the figure below.

It can be rotated while lifting upwards appropriately.

4. If the lifting shaft cannot be taken out, you can pinch both sides of the filter with both hands and lift the filter upwards evenly and forcefully.

This is shown in the figure below.

5. After the filter is lifted, you can clean up the perimeter of the shaft and the stolen goods in the barrel respectively, and then move the intermediate shaft by hand to check the flexibility.

6. After cleaning the stolen goods in the barrel and checking the flexibility of the shaft, clean the dirt in the center of the filter shaft, around the lid and all positions.

7. Then, align the spool in the strainer with the inner shaft of the barrel and install it, then check the flexibility of the strainer rotation, and finally buckle the plastic lid and press it tightly.