Can a nut on a quarter hose be folded off?

If it is rusty, you can knock on the galvanized pipe to drop some diesel. If it's ppr, knocking is useless. You turn it a little bit in the tight direction and then dismantle it.

Don't use too much force, I'm worried that you'll break the thread or break it inside. That's trouble. Can the faucet for cleaning floor heating pipes not be removed for a long time?

Yes, at present, there are three main methods for cleaning the dirt of floor heating pipes: chemical soaking, projectile cleaning, pulse wave physical cleaning, and chemical soaking cleaning. This cleaning method can fully dissolve the slime adhered to the pipe wall, and the high-quality food-grade raw material preparation used will not cause corrosion to the floor heating pipes, and the cleaning is thorough.

The disadvantage of this cleaning method is that some market speculators often use low-cost coercive agents, which can cause corrosion of pipes and related components. Can the faucet for cleaning floor heating pipes not be removed for a long time? Yes, there are currently three main ways to clean the dirt of the floor heating pipes:

Chemical soaking, projectile cleaning, pulsed wave physical cleaning, chemical soaking cleaning. This cleaning method can fully dissolve the slime adhered to the pipe wall, which makes.

There is a red and blue plastic bead or a small circle of other colors at the bottom of the handle, dig out the bead by hand or other tools, you can find a screw inside, take the screw to remove the screw, and the handle can be taken out. Then use a wrench or vise to remove the gland on the valve core, and the valve core can be replaced.

No, the M14 is metric, and the threads on both sides of the shower line are imperial, which is not the same.

This is a special joint for aluminum-plastic pipes, and this nut is the locking part of the joint, which is a must.

A round thing like a screw cap is on it. If it doesn't leak, there's nothing, right? Is it like this when it is actually pretended? Several.

This is a slipknot, which is used for pipe butting, which is normal.

It is the adapter of the aluminum-plastic pipe, which is used normally.

1. Close the total section door first. 2. You can pick up the washing basin and remove the two hoses (hot and cold water), which should be unloaded from the far end and the end of the water pipe. 3. The faucet passes through the vegetable washing basin, and the bottom is a sock plum with a large nut to fix the sensitive, and a large wrench is needed to unscrew the nut, and then the faucet can be taken off the vegetable washing basin.

4. Use a small wrench to unscrew the two hoses from the faucet in turn.

There is a wrench that screws the hydraulic hose very well, but it is a bit of an anti-aircraft gun to fight mosquitoes. It is recommended to make a special wrench by yourself, and the handle is bent at a special angle.

It can be installed and disassembled.

And that hose with a plastic screw sleeve on it.

Find out.

Loosen the nut on the left first, then tighten the right one, this is one with the hose, so the hose will follow;

If it is a snake hose connected to the commonly used washbasin faucet, it is a 4-point cluster to let the interface. Although the hose interface is 4 points, the inner diameter of the hose is smaller, and it can be replaced with Rifeng composite pipe, and the inner diameter of the hose should be slightly larger, which is not easy to block, and can be bent and easy to connect.

With PPR hot melt tube, because it is the supervisor, it should have a large inner diameter, you know?

The two ends of the hose of the vegetable basin faucet are not the same. If the end of the receiving basin is broken, twist it directly by hand in the counterclockwise direction.

The break can be screwed with needle-nose pliers.

It is also hand-screwed when installing.

If it is connected to the water pipe, the end is broken, and you need to use a wrench to twist it in the counterclockwise direction.

You can use a slotted screwdriver to rotate it diagonally, and if it is not easy to rotate, you can use a small hacksaw to pull a cut.

Loosen the bubble with a screw first, then remove it with an expansion screw or remove it with a foreign caliper.

First of all, let's see if the hose is still a little damaged.

Left on the outside or part of the inner filament remains on the outside

1. If you have one, you can try it.

Slowly clamp it with pointed mouth pliers and try to rotate the inner wire, pay attention to the direction, it should be counterclockwise, don't do it the other way around; Then the action should be light, and it will be more troublesome if you can't clip it.

2. If there is no outside at all, you can find a wooden stick of the same thickness and knock it in a little bit and try to turn it;

Second, you can try to pry the inner edge of the inner wire with a screwing knife to see if you can rotate the inner wire; If you can turn it out a little, then take method 1;

3. Use a screwing knife to jam the junction between the inner wire and the outside, and take it out after crushing.

The main sluice gate is closed and two trap wrenches are used to twist in pair. Don't lose the gasket inside, you can still use it.

Stir him up with a slotted wrench! Then find a thin iron and pull him out along the top! Then use a wrench to twist it in a counterclockwise direction.

I unscrewed the screws at the interface and replaced the entire hose.

Unscrew the hose fitting (inner wire) that is screwed on the faucet and replace it with a new hose.

It should be screwed down below. Buy a new one and screw it on.

First, close the water valve, buy a new pipe, find a wrench and unscrew it and replace it.

First turn off the switch of the water inlet or the water pipe (water meter) of your home at the entrance of the building, and then replace it directly.

: When the end is broken, twist it directly by hand in the counterclockwise direction; The break can be screwed with needle-nose pliers. It is also hand-screwed when installing.

You don't need to dismantle it, just buy a new one. I mean, you can't use it even if you remove it! Hopefully my suggestion you can use.

Pour hot water over it and take it off gently.

Cut the tube and reconnect it.