I heard from a friend that the quality of the tile with good water absorption is better, how to insp

Everyone thinks that the lower the water absorption rate of tiles, the better, because they feel that it is not easy to absorb dirt and take care of it, but it is not good to be too low. In the past, the water absorption rate of ceramic tile products was a few percent, and now many enterprises control it at one thousandth, and the construction is generally used in the past cement, which leads to the ceramic tile products can not be pasted, especially the products directly on the wall.

In fact, tiles still need a certain water absorption rate to ensure that the paving is firm. If you don't use any tile adhesive and only use cement mortar, choose this kind of clay brick with a water absorption rate of about 10%, the back of which is generally rough, which is conducive to sticking to the wall, and the bonding firmness is also better.

Industry insiders said that these problems can be avoided, first of all, the wall should be fully cleaned when paving, and the wall should be sprinkled with water a day in advance. In addition, consumers must ensure that the tile soaking time is sufficient, only to water the tile is not enough, should be put into the pot, soaked for 2 to 5 hours is appropriate, to the tile does not bubble.

In addition to the texture of the tile itself, there are some ways to ensure the strength of the paving, first of all, the first thing to choose is the first cement before pasting, there is a way to detect, put water and cement in the container to mix, the next day after the check its solidification degree, strong coagulation force can be used.

Secondly, the proportion of cement mortar should be appropriate. When pasting, it should be noted that the thickness of the adhesive material should be controlled between 7-10 mm, and it should not be too thick or too thin. When the back of the tile is full of mortar, it should be plastered into a beveled edge on the four periphery of the tile, and leave some gaps in the middle, so that when pressing and tapping the tile, the mortar will not overflow everywhere, and the mortar can be full, and the tile and the wall will be firmly combined.

To test the water absorption of the tile, just pour a little water on the back of the tile and let it stand for 5 minutes to observe the absorption of water. The quality of tile water absorption, determines whether there will be blackening of joints in the use process, mildew points, etc., the slower the water absorption, the better, the home in Hunan, the choice of Thompson ceramics is still very good, low water absorption, performance is very superior, back to Nantian do not need to worry, almost 6 years or new same.

This is a completely false rumor! In essence, the water absorption rate of ceramic tiles is high, indicating that the density of the tiles is loose and there is room for water storage. Such tiles are not only not dense enough, but also have insufficient stiffness, and are easy to be polluted and transmitted.

Really good tiles are tiles with particularly high density, such tiles not only have a particularly low water absorption, but also will not pollute the tiles even if the ink drops on them, and the tiles with high density are also wear-resistant and strong, not easy to break, in actual use, it is by no means a tile with high water absorption rate is a good tile. Don't be misled.

The quality of the tile with good water absorption, if you want to test this situation, you should pour water on it, so that you can see how good its quality is? The quality is even worse.

If the quality of the tile with better water absorption is better, then a certain inspection department will inspect it, and they have some equipment for professional inspection of tiles, which can test the performance of this tile.

It's not that the water absorption is good, the quality of the tile is good, mainly according to the tile. Gauge, specification and regularity and the surface of the tile, as well as his timbre to judge spontaneous tiredness.

If you want to test the water absorption rate of the tile, you can drop some water directly on the tile.

If you want to detect the water absorption rate of the tile, it is very convenient, you can put the tile in the water and see who has less.

This is not a very simple thing, when decorating and then paving tiles, before using a large basin of water to put the tiles into it, see how much water is left to know.

Hello, I heard from a friend that the quality of the tile with good water absorption rate is better, you can sprinkle some water on it to see which one absorbs water faster, which ***.

There is no such saying, one of the decorations is the ceramic tiles that absorb the force, and it is not the first ceramic tiles.

Haven't heard of itBricks with good water absorption are of better quality. Maybe you're mistaken. In fact, on the contrary, bricks with large water absorption rate are called face bricks, and the specific gravity of bricks is small and the quality is poor.

Novice friends only hit sparsely, good outfits are of better quality, and we can follow his discount to drink wild colors and come into contact.

And said that the tile is actually green and good spring quality is better how to test, this you are looking for a professional time to help you, explain it or check it on the Internet to understand it.

I think the water absorption rate of this tile is better, and the quality of the tile is also very good.

You don't want to be meticulous, and you don't want a lot of people to really believe pigs.

Low water absorption indicates that the density of the tile is higher, the density of the tile is higher, the quality of the tile is better, it is recommended to test the water absorption of the tile can pour a little water on the back of the tile, stand for 5 minutes, and observe the absorption of water. The water absorption of ceramic tiles determines whether there will be blackening of joints and mildew points during use, the slower the water absorption of the tile, the better, I tested the water absorption rate of Thompson ceramics in the field, and the performance is very superior. If you don't understand, you can go down again.

Tile selection of small details, simple 4 steps, hands-on brain to teach you to buy good building materials.

Tile paving is now a very willing material used in home decoration, its purchase and paving can make our home style more fashionable, but also reduce some unnecessary trouble. But when the tile is paved, we need to choose a good quality tile, otherwise it is easy to let it not provide us with much convenience, and various problems will begin to trouble our lives. Tile selection to use the manual brain to do the selection, even if a batch of produced tiles will be some substandard products, then we have to be more mindful in the process of buying tiles, to compare the quality of tiles to choose the most suitable and best style.

1.See. The most intuitive way for us to choose tiles, even if we look at it to observe it, to see how smooth and flat the surface of the tiles is, you can randomly take out a few tiles to compare when you choose, to see if its surface is intact without a little loss of electricity. And its periphery is not regular without any bumps and missing, which can ensure its better use effect.

2.Put together. We can randomly select a few tiles, and then put them all together, look at the stitching to see how the gaps between them are, and of course make their gaps very small. If the tile we choose is a style with a pattern, then we need to use 4 tiles to do the splicing to see if it will have a clear pattern and a unified color, which will decorate a more fashionable and beautiful effect.

3.Knock. We are optimistic that the style of tile can be beaten by hand, or with two tiles to beat it with each other, if the sound is that crisp, then the quality of this tile is very good. But the tile makes that muffled sound, this kind of tile should not be purchased, its quality is absolutely unqualified.

4.Drip.

We can pour it on the back of the tile with a cup of water, quietly observe and see how the water absorption rate of the tile is, if the water on the back of the tile is adsorbed away in the shortest time, it can show that the tile we choose has a high water absorption rate, so that it can play a better role in our lives.

Ceramic tile is the material we often choose for home decoration, but there will be a lot of details in its purchase to pay attention to, otherwise it is easy for us to choose the tile can not play a better effect, and the overall effect of the home will be affected, we can buy tiles in accordance with these methods to do experiments, if it can meet these conditions, then we can buy home to arrange our home into a beautiful and practical effect.

<> tile is a material that must be chosen for home decoration, and balconies, kitchens, and bathrooms are mainly pasted with wall tiles and floor tiles. So the question is, is there any relationship between the resurgence of floor tiles and quality? Why do the floor tiles at home reflux?

I believe that many people are not very clear. Especially the floor tiles, as long as the ant Paiqing is not the lowest layer (direct contact with the ground) should have nothing to do with it, the lowest layer of moisture is generally groundwater infiltration, the floor tile *** moisture will be better, the water can not be prevented will be more serious, and the air humidity is also related; If it is above the second floor, it is only related to the humidity of the air, according to my observation and practice, in this wayBack to the south weather

under the influence of the influence,The more often you open the windows for ventilation, the more serious the moisture return phenomenon of the floor tiles! The more "closed" the door, the less wet the floor tiles at home are.

And the floor tiles in the living room and bedroom on the second floor of my house are more high-grade than the floor tiles on the first floor, which is the kind of 800 * 800 glazed bricks that are stuffy in front of the first floor, according to the contrast quality of the ** is indeed much better than a dozen pieces, according to the contrast between the green body of the floor tiles and the porcelain layer on the surface, if you live in a dark and damp place and the first floor, it may be that the moisture insulation is not well handled, otherwise it is a commercial residential building, that is, the return of air humidity is a normal phenomenon. In general, the resurgence of envy floor tiles has little to do with quality, and you can use it with confidence.

I don't know if you live in a bungalow or a building: how many floors does the building have? If it's a bungalow, it's a residential floor.

If it is the first floor, there is also a problem with the bottom, and there is water below to the ground below. The reasons for the poor ventilation of the use space, such as the ventilation and dehumidification facilities of the closed space such as toilets and storage rooms are not perfect, and the lack of effective waterproof facilities in the use of water supply and drainage space.

Cheap tiles or engineering tiles absorb water, the hardness of the ceramic tiles is high, and they will not be broken under normal circumstances, and there will be no resurgence! When buying tiles, the seller will demonstrate on the spot that the tiles will not break! How much does it matter, the all-porcelain will not return to the tide of the clay, and the clay will not be accurate.

I think it has a relationship, because the quality of the tile is better, it is said that the water absorption rate of the ceramic tile is relatively high, and it is not easy to appear water seepage cracks, and the use time is relatively long.

Matter. Ceramic tile ***, the water absorption rate will be stronger, and this kind of cherry bright tile will not leave a water branch after mopping the ground, the cleanliness is particularly strong, and the aesthetics are also particularly strong.

Of course, there is a lot to do with it, the better the quality of the tile, the water absorption rate of the slag and hail tile is not so strong, and the good tile will not change too much even if it is covered by water.

It is related, because the better the quality of the tile, the stronger its water absorption, which is inevitable, so when buying tiles, you must buy a little bit.

It is related, if the texture density of the floor tiles is relatively good, it can achieve zero absorption, and if it is not good, it will absorb a lot of water.

Of course, it has a relationship, if the water absorption rate of the tile is too high, it will be easy to fall off, so this is also a way for people to judge.

Yes, it is related. Because many people pay great attention to the water absorption rate of tiles when buying ceramic tiles. This is also a very important criterion.

There is still a certain relationship between the two, if the quality of the tile is particularly good, then the water absorption rate of the tile will be relatively high.

Matter. I think it has a lot to do with it. If done well, then the water absorption becomes very strong.

There must be some relationship, if the quality of the tile is not good, its water absorption rate will be very poor.

Of course, it doesn't matter, because the current ceramic tile technology has been reformed, and it has nothing to do with water absorption.

I think there is a relationship, and the relationship is very important, and at the same time, it is very important, and people will choose to buy reasonably.

I think so too, because *** tiles are particularly easy to absorb water, so you must buy better tiles.

There should be some relationship, after all, the tile is placed on the ground, and it will often come into contact with water, and the water will affect the change of the tile.

There is a certain relationship between the two, if the quality of the tile is better, the water absorption rate of the tile will be higher, and it is also a better performance.

Very good and the same, because now the process of ceramic tiles has changed, unlike the previous need to soak a lot of water to pave, when choosing to focus on the glaze of the tile, choose the bricks produced in Guangdong, only the bending type can buy good bricks.

Normally, products with low water absorption are strong, not easy to expand, tight and hard, so they have high stability, are not easy to hide dirt and dirt, and are easy to clean. The density of tiles with high water absorption rate is relatively sparse, after water absorption, it is easier to produce the phenomenon of thermal expansion and cold contraction, resulting in the tiles are easy to expand and crack, if it is a wall tile, it will be easy to fall off, the floor tiles are easy to hollow, and the tile itself is also easy to absorb stains, affecting the overall appearance.

From the construction party's point of view, tiles with high water absorption are paved with ordinary cement mortar, while tiles with low water absorption need to be assisted by more viscous adhesives.

How to test water absorption|

Drip method: pour some water on the back of the tile, let it stand for 5 minutes to observe the diffusion and absorption of water, if there is no diffusion at all or the absorption speed is very slow, it means that the water absorption rate is low.

Tap the tile: Tap the tile with your hand, if the sound is crisp, it means that the water absorption rate is low, on the contrary, the sound is dull, the water absorption rate is high.

Professional tool measurement: the hardness of the tile is also related to the level of water absorption, if the hard object is scratched on the surface of the tile, there is no obvious scratch, such a tile often has a low water absorption rate.

The range of water absorption rate of various types of ceramic tiles|

The water absorption rate of various types of ceramic tiles ranges from: ceramic bricks "10% stoneware bricks" 6% fine stoneware "3% stoneware porcelain tiles";

Floor tiles are generally porcelain or stoneware, and the national general standard: 3% floor tile water absorption rate is qualified;

Wall tiles are generally fine stoneware, stoneware bricks or ceramic bricks, and the national general standard: 12% wall tile water absorption rate of 3% is qualified.

Different spaces correspond to different water absorption tiles

Kitchen wall tiles: glossy, oil-resistant, wear-resistant, glazed tiles are recommended.

Kitchen floor tiles: wear-resistant, non-slip, it is recommended to polish tiles and all-body tiles.

Bathroom wall tiles: matte, moisture-proof, glazed tiles are recommended.

Bathroom floor tiles: non-slip, wear-resistant, low water absorption, it is recommended to polish tiles and full-body bricks.

Living room wall tiles: wear-resistant, dye-resistant, easy to clean, it is recommended to vitrified tiles, polished tiles, and full-body tiles.

Living room floor tiles: glossy, scrub-resistant, porcelain tiles, full glaze is recommended.

The lower the water absorption, the better the quality of the tile

The lower the water absorption, the better the quality of the tileThis sentence is actually unscientific, many things will be reversed, and tiles are no exception. If the water absorption rate is too low, it will lead to the problem of tile falling off. Why?

Because the tile has a certain water absorption rate, so when paving with cement slurry, the tile will absorb the moisture in the cement slurry and fix the word, forming a grip on the wall, if the water absorption rate does not reach a certain level, it can not absorb the due moisture, so as to reduce the grip on the wall.

In addition, tile adhesives can be used to assist in tile laying. However, if you only use cement slurry to pave, it is recommended to purchase tiles with a water absorption rate of about 10%, and its adhesive firmness is the best.