How to check the fault of Xiao X0 a C0v4342 elevator does not open the door

Summary. Hello, I'm glad to be able to answer your questions for you, please wait for two minutes, I see your question here, and I'm going to inquire about the relevant information for you, the teacher also needs time to type, please be patient and wait for two minutes! Please don't end the consultation|! <

<>Theo elevator failure**.

Hello, I'm glad to be able to answer your questions for you, please wait for two minutes, I see your question here, and I'm going to inquire about the relevant information for you, the teacher also needs time to type, please be patient and wait for two minutes! Please don't end the consultation|! <

<> above is the complete list of Xiao elevator failures, you can refer to it, it will help you and hope to give a thumbs up.

How to deal with the fault of Xiao elevator 029 Hello dear, The elevator clears the fault code method as follows: 1. Press the mod button, which is displayed as pressing the num button several times, and stops when the 8-segment digital display shows 0e. 3. Press the num button once, the 8-segment digital display display shows that the STB button is pressed once, and the 8-segment digital display displays 0E.

If 0e does not appear, repeat step 2. (At this time, the E1 fault has been cleared) 5. Press Num twice, the 8-segment digital display display displays the STB button once, and the 8-segment digital display displays 0E. If there is no 0E, repeat step 2 (the E2 fault has been cleared at this time) 7, press Num three times, the 8-segment digital display display, press the STB button once, and the 8-segment digital display display shows 0E (the E3 fault has been cleared at this time).

9. Press and hold the PRS button for 5 seconds. At this point, the elevator fault has been cleared. The elevator automatically returns to the base station and the 8-segment digital display shows the floor on which the elevator is located.

Summary. Hello, I'm here to help you solve this problem. Qinqin Theo Elevator reported 400 401: This fault indicates that the state of the brake switch is incorrect. Please check the status of the brake switch during the operation of the elevator and after it has stopped.

It should be a short circuit problem on the side of the switch, it is recommended that you find a professional maintenance personnel to take a look, do not repair it privately, so as not to cause secondary damage. The above is all my reply, I hope it can help you, I wish you a happy life

Theo Elevator reported 400 401 How to deal with the fault.

Hello, I'm here to help you solve this problem. Kiss Theo Electric Imitation Hall Ladder Report 400 401: This fault indicates that the state of the brake switch is incorrect.

Please check the status of the brake switch during operation and after the elevator is stopped. It should be a short circuit problem on the side of the switch, and it is recommended that you find a professional maintenance personnel to take a look, and do not repair it privately, so as not to cause secondary damage. The above is all my reply, I hope it can help you, I wish you a happy life

The server checked and showed that the two remote stations had an address conflict and that the remote serial line synchronization signal was lost.

Hello, I'm here to help you solve this problem. Kiss the Lord suggests that you let a professional master come to repair it

Here are two elevators connected in parallel, I feel that there is a problem with outbound communication, every time it breaks, the two are going to stop one floor.

Hello, I'm here to help you solve this problem. Kiss you can measure the voltage.

The outbound call voltage is 23V

Hello, I'm here to help you solve this problem. It is recommended that you find a professional repairer to repair it.

When the door lock is short-circuited and faulty, the elevator is automatically operated, and there is no door lock for parking, and the door lock is disconnected from the royal process 1 Check whether the door lock circuit action is normal; 2. Check whether the electric shock action of the door lock contactor feedback is normal; 3. Check that the system has received the signal from the door to the mold sock position when the door lock signal is valid;

Dear, I'm glad to answer for you! Xiao elevator fault **L004 indicates that the car door lock switch (S5) signal is abnormal. This failure occurs in the control system of the elevator door and requires the following inspection and maintenance:

1.Check the door lock switch: Check whether the door lock switch (S5) is damaged or loose.

Yes, please replace or re-fasten the door lock switch. 2.Check the wiring connections:

Check for damage or poor contact with door locks, switch cables, and other wiring. Make sure all wiring is properly connected and reinstall or replace parts that need to be repaired. 3. Check the controller board:

Check whether the circuit board of the elevator controller has old problems, such as poor soldering, damaged components, etc. Please repair or replace the controller circuit board. 4.

Reset the elevator controller: Sometimes, false alarms occur due to software errors or other issues with the elevator control controller. Try restoring the elevator controller to factory settings and restarting the elevator.

Theo Elevator Failure**AL004 usually indicates a faulty elevator door lock. When the elevator door lock is not working properly, the elevator will stop running and show AL004 fault**. The steps to solve this problem are as follows:

1.Restart the elevator: First, try pressing the restart button on the elevator to see if you can restart the elevator and clear the fault**.

If the failure** persists after the reboot, further investigation is required. 2.Check the door lock circuit:

Check the circuit of the elevator door lock to make sure that the door lock circuit is not short-circuited or open-circuited. If a circuit fault is found, the circuit component needs to be repaired or replaced. 3.

Check the door lock switch: Check if the elevator door lock switch is working properly. If the door lock switch is faulty, the door lock switch needs to be replaced.

4.Check the door lock solenoid: Check whether the elevator door lock solenoid is working properly and the return key.

If the solenoid fails, the solenoid needs to be replaced. It should be noted that elevator failures involve safety issues and should be overhauled and repaired by professional elevator maintenance personnel. When overhauling and repairing elevators, you should strictly abide by the safety regulations and operating procedures of the relevant Shishishen to ensure safety.

Hello dear <>

Theo elevator fault AL004 refers to the communication failure between the elevator system controller and the door control system. This can be caused by a faulty line or device in the door control system, a faulty communication module of the controller, a power supply problem, or other factors in the bridge. Workaround:

1.Check whether the wiring and equipment of the door control system are working properly, such as door locks, door magnets, light curtains, etc. 2.

Check whether the connection of the elevator controller communication module is loose or damaged. 3.Check whether the power source of the electric punch is normal, such as whether the power supply of the controller and the door control system is on or whether the voltage is normal.

I wish you a happy life! Hope mine is helpful to you.

Hello dear. In Theo Elevators, a 0030 fault** usually indicates an "ID-CAN communication failure". In the process of elevator operation, data exchange and communication need to be carried out between the various controllers of Xiao Elevator to realize the coordinated operation of the entire slag system.

The ID-CAN communication fault indicates that some controllers cannot communicate normally, which may be caused by poor cable connection, interface damage, and internal obstruction of the communication controller. This may result in failure situations such as the elevator not functioning properly, stopping, opening the door, or alarming. If your elevator has a 0030 failure**, please contact the after-sales service personnel of Xiao Elevator in time for troubleshooting and maintenance.