How can rural areas build their own piped water systems? 20

Here's how:

1. First of all, you need to put a large container of water at the highest point of the room.

2. Connect a water pump at the water inlet, and the switch part can be manually controlled or equipped with an automatic control system.

3. The advantage of manual control is that the installation cost is low, but it is easy to cause overflow. Automatic control systems can avoid this problem, but the installation cost is higher.

4. The water outlet hole of the bucket is generally divided into two branches, one of which is directly connected to the water pipe of the family to provide cold water for daily life; The other one is connected to a solar water heater.

, through solar energy to provide services for daily use of hot water.

If you buy a bungalow, you can buy a thermal water tank and put it on the roof, and you can lead the water pipe down, not a bungalow to make a single shelf to put the insulated water tank on it, higher than the roof, and when there is water in the village, you can find a water pump to pump it into the water tank! The insulated water tank is sold on a treasure. The total cost can be done within 5,000!

There is a running water system everywhere in the countryside. If there may not be one in a very remote place, a well will need to be drilled to get water for drinking.

Just find a worker to install it.

Nowadays, with the rapid development of rural areas and the continuous housing prices in cities, more and more young people choose to go home and build houses instead of buying houses in the city as before. Year. Building a favorite house at home has become the choice of many young people who go out.

The issue of water for self-built houses is very important. In rural areas, water and electricity have been uneven. The problem of power supply is largely not a problem, but the solution to water supply is not satisfactory.

A considerable number of rural households have not yet opened running water, even if the water pressure of the households with running water is insufficient or the water supply is supplied at different times, so many rural people still choose to dig their own wells to pump water, which is quite inconvenient. Today, I will introduce you to several water supply methods for self-built houses. A pressure tank is the most convenient solution:

Without running water, you need to dig your own wells, pump the water, and store it in tanks or buckets for household use. In this case, we need to solve the problem of how to provide a stable and continuous water supply pressure for households, meet the water supply needs of electrical appliances such as solar washing machines, and avoid secondary pollution by traditional water storage methods. Two solutions are given.

One: Choose a pressure tank. The working principle of the pressure tank is to use a water pump to pump water into the pressure tank, and then pressurize the water in the tank through the principle of compressed air.

In this way, the water coming out of the tank is pressurized, and it is easy to finish building with water or solar energy. The advantage of this scheme is that the whole water use process is closed, and there will be no secondary pollution in the water use process, that is to say, it will not be secondary pollution by foreign bodies, as long as the problem is to solve the problem of the material of the pressure tank itself. Well, 304 food-grade stainless steel is generally chosen.

There are no rigid requirements for the installation position of the pressure tank, and the advantage of this method is that it is easy to install. Because the pressure tank itself is pressurized by compressed air, the installation site requirements of the pressure tank are very low, and there is no need for a traditional water tank. It is also installed on the roof or at a height, pressurized by the height difference.

In other words, we built a small water plant for our own use, with a pressure tank and pump, and even a simple filtration device at the entrance of the pressure tank to ensure the safety of the water quality. What kind of water supply effect will we have after the installation is completed? Every faucet in the home, whether upstairs or downstairs, will ensure that there is water 24 hours a day, and water equipment such as solar energy can also ensure sufficient water pressure.

And because the pressure tank will be equipped with equipment such as pressure tank pressure switch and pressure gauge, when the pressure in the pressure tank drops, that is, the water storage decreases, the pressure switch will control the water pump to replenish the pressure tank itself, so we also solve this problem. It eliminates the need to switch the pump to pump water and provides automatic water supply. The pressure generated is enough for the washing machine to run on solar energy.

2. Select the water tank for water supply. This is a more traditional way of water supply. The water tank is placed higher than the water supply position and is supplied through the water level drop.

Here's how:

1. First of all, you need to put a large container of water at the highest point of the room.

2. Connect a water pump at the water inlet, and the switch can be manually controlled or installed with an automatic control system.

3. The advantage of manual control is that the cost of installation is low, but it is easy to cause overflow. Automatic control systems can avoid this problem, but the installation cost is higher.

4. The water outlet hole of the bucket is generally divided into two branches, one of which is directly connected to the water pipe of the family to provide cold water for daily life; The other is connected to the solar water heater to provide hot water for daily use through solar energy.

Different regions are charged according to different regulations. Taking the rural area of Youba Township, Qianshan Tingran County as an example, according to the "Law of the People's Republic of China", the Provincial Price Bureau's "Notice on Printing and Distributing the Regulations on the Management of Rural Water Supply" and other relevant laws, regulations and policies, the supporting fees (installation fees) of the rural tap water pipe network are legally formulated through the procedures of enterprise declaration and cost supervision and review. The county price bureau approved the supporting fee (account opening fee) of the oil dam waterworks pipe network as 2,200 yuan for households, and only 380 yuan for farmers who enjoy the rural drinking water safety project, and the off-balance sheet material fees and installation fees are charged according to the actual amount.

The charging standard for the installation of tap water projects in rural areas is based on the water consumption situation of the whole dry village and the actual situation of each water use point, and the overall planning is carried out through the actual investigation and calculation of the statistical cost on site.

1. First of all, the foundation should be started, and then the backfill should be carried out, followed by the structure of the main body, and then the indoor work should be carried out after the capping, and the indoor drainage pipe should be laid first.

2. Design the location and direction of the pipeline.

Under normal circumstances, the bathroom should have at least a toilet drain, a floor drain, a washbasin drain, and if a pier cloth basin is set up, a bathtub, etc. Remember to keep a distance away from the water mains. In the kitchen, consider at least one sink drain and one floor drain, and increase the number of drains according to personal preferences for kitchen design.

The direction of the pipeline should be ensured as much as possible in a main line, with a certain slope and as few corners as possible. The pipeline can be installed, and it is necessary to do a good job of glue, otherwise it will be too difficult to solve the water leakage in the future.

Add a U-shaped before connecting to the sewage treatment well at the end of the pipeline, so that you can use water to separate the smell of the sewage well, and families with less water should remember to open a large amount of water to flush the pipe after a period of time, and it can be done for a few minutes, so that you can avoid oil pollution blocking the U-shaped section and anti-odor upward.

Rural tap water is generally divided into two types according to the water source:

First, the public pipe network, this is very simple, either directly connected to the public pipe network, or first use the pipe to introduce the water distribution point of a certain waterway at home, this point should be connected to the water meter, only through the water meter can the water be sent to various places where water is used;

In addition, in order to prevent the water pressure from being insufficient or the water is cut off, you can install a water storage tank on the roof of your house, and the water storage tank is best to use an automatic water dispenser, so as to avoid the inconvenience of artificial water supply. The water is then diverted through the tank to various places where the water is used.

Second, self-drilling, is to dig a well, and then use the lifting pump to lift the water to a certain height, generally is to set up a water storage tank on the roof, the same, it is recommended to use the automatic water feeder, and the pump linkage, save the inconvenience of manual water. The water is then diverted to the various points of use through the water storage tank.

Judging by your problem description:

1. The height of the water tower in the village is generally more than one floor, so you only need to install a stainless steel water storage tank; Water can be supplied from the village's own water tower.

2. Required materials, water storage tank, PPR water pipe, PPR pipe joint, shut-off valve. Faucets, sinks, sewer hoses.

3. Considering that you need to use water in the kitchen, it is recommended to dig a seepage pool in the yard and use a pipe to introduce the sewage into the seepage pool, so that the family does not have to run the wastewater outside.

In terms of cost, the water tank buys 300 kg, about 500, the pipeline is very cheap, the pipeline of the first layer of the road plus accessories, about 200, the vegetable sink, the faucet or something is basically about 300, the labor cost is mainly hydraulic installation, 300, of course, there is the money for digging the pit in your home, if you dig it yourself, it is simple, of course, the pit is dug, and you have to fix it around with red bricks, etc., and then cover it with cement prefabricated panels.

The entire project amount is almost 2000 can be done.

Specialty wild boar farms need to build an automatic water supply system. The number of pigs raised in the pig farm is large, and the automatic water supply equipment produced by professional manufacturers can be purchased, but the investment is large; Medium-sized farms can be built by local methods, which requires less investment. The number of pigs is small, you can buy a large plastic bucket on the market, and the best water pipe is PVC pipe, one is cheap, the other is corrosion-resistant, and the service life is long.

A house at one end of the feeding room or feed room is built into a bungalow, and the rest of the houses can be ridged, and the house sits in the north and faces south, making the middle of the bungalow in the storage tank, and building a cement beam in the east and west directions for load-bearing. Then, a water storage tank is built on top of the bungalow, and the height of the house is used to generate pressure and the water is piped directly to the individual pig houses.

The walls of the pool should be built on top of the walls of the house to increase the load-bearing capacity. Generally, two 3 m 3 m pools with a height of 3 m can be built to store 27 32 tons of water. The well water is pumped directly into the pool with a high-pressure pump.

It costs less than 1,000 yuan to build a small pool in this way, but it works very well.

If it is multi-storey, and each floor has a water room, then it must be up and down in the same place to facilitate the pipes. Only the first floor does not need to consider this.

After the floor plan of the self-built house has been determined, the branch line and main line are determined according to the location of each water tap or valve in the water room. Generally, the kitchen has a water supply pipe, a drain pipe, and if there is hot water, there is also a hot water pipe. The indoor toilet has faucet water supply, water heater water supply, toilet drainage, and floor drain drainage.

The location of the washing machine also needs to take into account water supply and drainage. Reverse reasoning is enough, and what functions you need need need to lay out what pipes. The same goes for electricity.

Try to consider that it is all buried, go under the ground, if the pipe is relatively small, you can also consider walking into the brick wall, and the same as the reserved wire hidden pipe to carve grooves in the brick wall in advance.

Outdoors try to be buried in the soil directly by the roadside, if there is an outdoor faucet in the north, you must consider anti-freezing and heat preservation.

In addition, you have a specialization in the industry, think about the required functions comprehensively, and then ask a professional worker to help you plan the location of the pipeline.