Audi s own method of adding engine oil, how to add engine oil to Audi A6

Step 1: Run the ** motor to bring it to the working temperature. Then use a jack.

Jack up the vehicle and pull the handbrake.

The car and squeezed the front wheels with wooden wedges.

Check the drain bolts, reinstall the drain bolts, and be careful not to tighten the bolts too tightly to prevent damage to the oil pan.

Step 3: Move the oil container under the oil filter and use the oil filter wrench.

Unscrew the filter and unscrew it by hand. If the filter is still hot, remember to wear gloves. Don't worry about the filter being tightened and damaging it during removal. As long as you don't damage the connection screws on which the filter is installed and the parts around the filter, you'll be fine.

Step 4: Refer to the user manual to select the appropriate oil filter.

Step 5: Apply the interface gasket of the new filter cartridge with new oil. If the filter is installed vertically, you can pour some fresh oil into the filter, which will reduce dry grinding the next time the engine starts.

Screw the filter in by hand and tighten the filter as indicated (usually after tightening the filter by hand and then screwing it in 3 or 4 turns).

Step 6: Next, add the new oil to the oil pan, refer to the user's manual. A funnel can be used to prevent oil from being poured on the outside of the engine.

Check the lower part of the engine for leaks. If there are no leaks, put down the vehicle, check the dipstick, and start the engine. The indicator light on the meter should turn off immediately after starting.

Finally, turn off the engine and repeat the oil level. Dispose of used oil and filters according to local regulations.

If you add your own engine oil, you can add it directly. Generally, you can open the oil port from above and add it in.

The way Audi refuels itself is by having to lift the car. Or drive in and you can change. Borgundy case.

Open the oil pan and let the oil out. Replace it with a new oil filter. Then there is a home on the engine, first understand this Audi car.

How much oil can be used, and when adding, it is assembled. Don't add too little cold noodles, and don't add too much to play with the high family for a while.

Open the engine cover, find the oil cap, open it, refill a litre, and check the oil level.

Audi adds engine oil by itself in the same way as in the repair factory No. 4S shop, the main thing is to open the oil cap. Next, you have to lift the car up, and then put the oil out to change.

You'll want to find your engine drain and put the oil out and then add the oil yourself.

If you have professional equipment you can change it yourself, if it is not recommended to go to a professional place to change.

You can go directly to a general auto repair shop and give a 50 yuan for it.

Engine oil can lubricate and reduce wear, assist cooling and cooling, seal leakage, rust and corrosion, shock absorption and cushioning of the engine. It is known as the "blood" of automobiles.

Engine oil is made up of two parts: base oil and additives. Base oil is the main component of lubricating oil, which determines the basic properties of lubricating oil, and additives can make up for and improve the shortcomings of base oil performance, give some new properties, and are an important part of lubricating oil.

Main advantages: The amount of lubricating oil should be controlled between the upper and lower scale marks of the dipstick. Because too much lubricating oil will enter the combustion chamber from the gap between the cylinder and the piston, and burn to form carbon deposits. These deposits can increase the compression ratio of the engine and increase the tendency to detonation; The carbon deposits are red hot in the cylinder and can easily cause premature ignition.

Process: 1. Heat up the car for 10 minutes (the hotter the oil, the better), park the car in a flat place and pull up the hand brake.

2. The jack erects one side of the front side of the car, puts it into the bracket, then erects the other side and puts it into the bracket, and at the same time puts the jack insurance, and puts the rear wheel on the obstacle to avoid moving outside, safety is still the most important.

3. Drill into the bottom of the car and remove the engine guard.

4. Find the position of the filter and the oil drain screw, the machine filter is a white cylinder, the oil drain screw is at the bottom end of the oil pan, be careful not to make a mistake with the transmission oil shell, the oil pan is generally located in the front of the car, second only to the radiator.

5. Drill under the car again, use a hexagonal wrench to get the oil drain screw, and then slowly turn it away with your hands, pay attention not to be burned by the oil, and use the basin as soon as the oil comes out.

6. Open the hood, open the oil cap, and the air circulation is smooth. Use a wrench to start the unloading filter.

7. Wait for 20 minutes and wait for the oil to basically not drip, wipe the area around the mouth, install the new machine filter, remember to wet the oil filter rubber ring with engine oil before installation, and tighten the machine filter by hand without a wrench.

8. Install the oil discharge screws, and you can also replace them with new ones. Use the funnel to refuel the engine, stop when it reaches 4 liters, see if the dipstick reaches the lowest, and then you can start the engine to check the leakage, you need to step up.

9. Replace the guard plate, put down the car, and continue to add oil to the middle of the oil scale, not too much, not too little. Pay attention to the engine oil, do not dump indiscriminately, and protect the environment.

Under normal circumstances, the oil truck is generally used to suck up the waste engine oil in the engine!

Then refill the oil.

The engine needs to be added with 5 liters of oil! The actual refill amount is about that!

A maintenance reset is then required in the MMI. In this way, when the car is warmed up again, you will see that the oil column is in the MAX state in the MMI!

Hope it helps!

Remove the engine floor, you can see the oil pan oil screws, remove the screws, the oil can be all released, when the oil is not released, you can disassemble the oil filter element, the oil is put into the screw as it was original, replace it with a new oil filter element, open the front cover, there is an oil to add a hole, you can add some oil first, while watching the oil is late, add the oil at the same time, add to the fast top position of the oil late.

German Volkswagen Maintenance Group is looking for lubricating oil and energy-saving engine oil suppliers.

Read the manual, or ask the driver who has driven the car to know, otherwise go to the 4S store to deal with it.

Let's go to the garage, I can't tell you that.

1. Audi A4L

Add nearly five liters of oil, add the amount inside, if it is LDH5W-40 this empty liquid to quart.

According to the company's calculations, it is about 5 bottles. All in all, when added to the upper and lower limits of the dipstick, it is suitable for the slag loss. Wild.

2. On the multi-purpose display of the center console, the remaining oil of the organic oil shows that the oil consumption of the A4 series is a common phenomenon, and it must be checked from time to time (the oil volume is proposed to be 2000km once).

3. Put the car engine.

When the bin is opened, you add 4 liters first, and see where the dipstick is, generally add it to the middle of the grid or to the middle of the concave groove.

Engine oil is equivalent to the blood of the car, bringing endless power to the car and braking. Engine oil is indispensable for machine lubrication, especially for the engine. Too much or too little is not good, generally the highest liquid level is a little lower, and it is necessary to check regularly.

Before the inspection, the vehicle should be parked on the horizontal plane, and the engine should be started to idle for 5 mis "minutes";

Stop the engine, wait for 3 mis, pull out the oil dipstick and wipe it clean, reinsert the dipstick and take it out again, and record the oil level on the dipstick;

The correct oil level should be between the highest and lowest positions;

Use your hands to beat the oil on the dipstick and check its viscosity to see if there is a gasoline smell and bubbles.

If the oil level is too high, the cause should be ruled out even if the reason is inquired, and the cause may be cooling water.

or gasoline entering the crankcase.

Five misunderstandings about the use of automobile engine oil:

Myth 1: Engine oil is often added but not changed.

For some Ashkenazi burn oils.

For car owners, it is not wrong to check the engine oil frequently, but only replenishing and not replacing it can only make up for the lack of oil quantity, but it cannot fully compensate for the loss of lubricating Senbi oil performance. During the use of engine oil, the performance will gradually decrease due to pollution, oxidation and other reasons, and there will also be some consumption, so that the quantity will be reduced.

Myth 2: The role of engine oil additives is large.

A good quality oil is a finished product with a variety of engine protection functions, and the formula already contains a variety of additives, including anti-wear agents, and the oil is most important to balance the formula to ensure that the performance is fully realized. Adding other additives by yourself not only does not bring additional protection to the vehicle, but is easy to react with the chemicals in the oil, resulting in a decrease in the overall performance of the oil.

to make the oil circuit unblocked. For example, in the high temperature season or under the condition of severe engine wear, the selection of high viscosity oil is conducive to the formation of oil film and reduces engine wear.

1.Fully synthetic engine oil: Fully synthetic engine oil has better high and low temperature performance, longer oil change interval and is suitable for more severe car conditions, suitable for luxury high-performance vehicles, and is replaced at about 10,000-12,000 kilometers.

2.Semi-synthetic engine oil: The replacement cycle of semi-synthetic engine oil is generally about 8000-10000 kilometers, and the performance is moderate.

3.Mineral engine oil: This type of engine oil needs to be replaced at about 5000 kilometers as soon as it is imitated and hidden.

Try to choose multi-grade oil, multi-grade oil has a better protection effect on the engine due to saving, long life and high efficiency. Based on the characteristics of multi-grade oil, premature blackening and oil pressure may be smaller than that of ordinary oil during use, which is normal.

1.Engine oil, that is, engine lubricating oil, can lubricate and reduce friction, assist cooling and cooling, seal leakage, rust and corrosion, shock absorption and cushioning for the engine. It is known as the "blood" of automobiles.

2.Engine oil is made up of two parts: base oil and additives. Base oil is the main component of lubricating oil, which determines the basic properties of lubricating oil, and additives can make up for and improve the performance of base oil, and give some new properties.

3.The 5W W-30 and so on in the engine oil indicate the viscosity grade of the engine oil, which is the SAE grade. "W" means winter.

The smaller the number in front of the preparation hall w, the smaller the low temperature viscosity and the better the low temperature fluidity, which increases the importance of the Chinese market and the lower the minimum temperature applicable to the Chinese market as its global market. The number after w does refer to the viscosity of the oil at 100 degrees Celsius, and the higher the number, the more viscous the oil. The main line of the following numbers refers to the index of the high temperature resistance of the engine oil, and the better the protection performance at high temperatures.

Of course, the better, the better.

Audi uses fully synthetic motor oil, preferably 5w40 or better 0w40 oil, which does not solidify easily at low temperatures. W stands for winter, and the number in front of w represents the flow performance at low temperatures, and the smaller the value, the better the start-up performance at low temperatures. The number after w represents the stability of the oil at high temperatures (i.e., the possibility of thinning), and the higher the value, the better the stability of the oil at high temperatures.

Since engine oil has a great impact on the performance and life of the engine, the same series, use grade and viscosity grade of engine oil should be selected in strict accordance with the provisions of the automobile instruction manual. The engine oil recommended in the vehicle manual is determined according to the performance of the engine and the temperature of the sales area, which has a certain guiding role in the selection of engine oil, and leaves a large safety factor, and is also one of the prerequisites for claiming during the engine warranty period.

Audi is a well-known car developer and manufacturer, and its logo is four interlocking rings. It is now a subsidiary of Volkswagen AG of Germany, headquartered in Ingolstadt, Germany, and its main models are A1, A3, A4, A5, A6, A7, A8, Q1, Q2, Q3, Q5, Q7, Q8, TT, R8 and S, RS performance series.

The Audi sedan logo is represented by four rings, representing the four companies before the merger. These companies used to be manufacturers of bicycles, motorcycles and passenger cars. Since the company was originally formed by the merger of four companies, each link is a symbol of one of the companies.