How to go to the house inspection for decoration? What are the key points? Details,

Generally, it is water and electricity inspection, windows, walls, etc.

For the first decoration, you should use a hammer to tap the wall during the house inspection, and you can check whether the wall is hollow. Many people have a lot of problems because they are not careful when they inspect their homes. But in the end, there is no reason to find a decoration company, so at this time, we must do the meticulous problems in the process of house inspection.

Moreover, it is necessary to look at the check area on the contract, and at the same time to see if there are other omissions, and compare it with the structural drawing, so as to achieve the desired effect. <>

And when receiving the house and inspecting the house, it is necessary to understand the area of the contract and the actual area, as long as the difference is within 2%, there is no big problem, but if it exceeds 2%, it is necessary to agree on compensation. When inspecting the house, you must remember to bring a tape measure, and use the tape measure to measure whether it is consistent with the contract. More importantly, all these data should be recorded, so that they can be better checked.

You can take a basin of water and fill each drain to see if the water flow is smooth. <>

Under normal circumstances, the sound that everyone hears should be gurgling, so that there will be no water accumulation. However, if the faucet is turned on and tested and the water flow is found to be abnormal, it is necessary to find a renovation company to solve the problem. And be sure to check whether the wall is flat, see if there is any water seepage, and also pay attention to whether there are water traces on the bottom surface and the outer wall.

If so, look at the reason and solve the problem while the renovation team is there. <>

If the danger is not particularly large, but a crack is found in the interface, then be sure to inform the developer. And in the process of inspection, the main gate should be closed, to see if there is a power failure in the room, and you can also check the lines controlled by each switch. If the circuit is smooth, there is no problem, the house inspection is originally for their own interests, if you don't pay attention to there are some loopholes, then it will affect the living effect.

Be sure to check the water pressure and voltage, pay attention to the laying of pipes and wires, pay attention to the wall structure, be sure to check the content of the contract, to clarify the detailed rules, to check whether there are defects in the interior of the house, to check the verification area inside the contract, to check whether there is any leakage on the wall.

It is necessary to pay attention to the steps of house inspection, pay attention to whether there are cracks in the house, pay attention to whether there is a hollow drum on the wall and ground, pay attention to whether the bathroom is waterproof, and check whether the house is tilted.

During the house inspection, it is necessary to pay attention to check whether the site is cracked or not dry, whether the seams are good, whether the doors and windows are closed, and whether there are leaks.

During the house inspection, it is necessary to pay attention to check whether the site is cracked or not a dry environment, whether the beautiful seams are done, whether the doors and windows are closed, and whether there are leaking seams.

What should I pay attention to in the home inspection? Teach you the steps to receive the house, don't be fooled after reading! Life Tips, Life Tips, Life Tips, Life Tips.

1. The installation of doors and windows must be firm, horizontal and vertical, up and down, and the doors and windows should be opened flexibly, without obstruction and ** phenomenon. Complete hardware accessories. The door lock is installed in the correct position, and the switch is flexible and effective.

After the installation of doors and windows, the surface should be clean, and there should be no scratches and bruises on the large surface. The large surface of the paint film should be flat and smooth, uniform in thickness, and free of pores. Wood products, curtain boxes, heating covers, wooden parapets, wooden partitions, door and window covers, baseboards and decorative lines, etc., must be nailed with solid nails and no looseness.

The lining plate and the panel must be firmly bonded, and shall not show the phenomenon of layering and bulging. The paint should be flat and smooth, with smooth whiskering and color differences.

2. The installation of hot and cold water switches, faucets and showers in the bathroom is straight, and the use of flexible and bento can be repeated several times during acceptance to see if the water flow can change with the opening size of the water section door. The drainage pipe should be unblocked, no slope, no blockage, no leakage, and the floor drain grate should be slightly lower than the air. During acceptance, the water should be repeatedly filled and discharged, and the drainage can be checked to see if the drainage can be smooth.

3. Wall and floor tile paving: Wall and floor tile paving should be smooth and firm, the joints should be uniform, and the local hollow drum should not exceed 5 of the total amount. The contact between the air waterproof layer of the kitchen and toilet and the wall should be turned upwards and raised not less than 250 mm above the air. The surface layer of water in the air slopes to the floor drain, no flooding, no water accumulation, and no leakage in the 24-hour water storage experiment.

Decoration renderings Chinese-style living room.

4. The finishing project of the wall top coating project implores that the putty should be separated from the substrate and solid, solid, not peeling, not chalking, and not cracking. It is strictly forbidden to peel the latex paint, leak the brush, and penetrate the bottom, and there is no falling and wrinkled skin on the large surface, and the surface color is different, and there are no obvious brush marks.

5. When the top hanging mirror line, top corner line and other wooden decorative lines are docked, it is advisable to use 45 degrees of glue slope joint, and there shall be no staggered seams or seams at the joints. Pray for a straight and even divergence, close to the wall, and close the circle correctly. The ceiling keel shall not be twisted or deformed, and the installed keel shall be strong and reliable.

The gypsum board cover of the paper surface is tightly connected with the keel, and the galvanized screws should be fixed on the keel, and the nail head should be brushed with anti-rust paint.

6. After the completion of the construction of the electrical engineering of the electrical project, the necessary inspection and experiment should be suspended, such as the lighting test and the switch test control, and the switch and switch several times. Check whether the line can meet the plea of "front line into the switch, zero line into the lamp head", and the socket should meet the rule of "left zero right fire, grounding on the top". The switch and socket panel should be installed firmly, in the correct position, with a correct cover plate, a smooth surface, close to the wall, and no gaps around.

The height of the switch or socket in the same room should be different. When the project is completed, the construction unit should be asked for the completion diagram of the wiring, indicating the wire specifications and the direction of the hidden pipe.

During the house inspection, it is required to check the relevant information of the developer - five certificates, two books, one table and delivery. Weibo Repair has arrived.