The screw mouth of the water pipe is broken, how should it be blocked

Connect a plastic container (you can use a take-out plastic bowl) under the pipe joint where the broken wire is to be removed to prevent the residual liquid from splashing everywhere; If you use iron pipes in your home, cover them with a plastic bag to avoid pinching and corrosion。Use a small plastic container (yogurt box) to hold a little hydrochloric acid, and then use a cotton swab dipped in hydrochloric acid to apply to the two crevices adjacent to the broken filament to corrode. The effect is quite noticeable, and bubbles are also produced.

When you can see the copper teeth underneath, you can use a saw blade, screwdriver and other tools to remove the broken wire. When removing the broken filament, wipe off the residual liquid in the tube with toilet paper before removing the broken filament. Then corrode the 2 adjacent gaps, and the gaps between the gaps should not be too large.

When the two sections of broken wire are corroded and only half of the broken wire is left, you can use a saw blade, screwdriver, and other tools to unscrew the broken wire from the remaining tube.

Most of the problems are solved by replacing them with new ones. However, if the faucet is broken, it is even more troublesome. The old screws can't come out, and the new faucet can't be installed, which is very troublesome.

Faucets are generally made of alloy. Although alloys generally have some rust resistance, faucets can still rust if they are exposed to water and air on a daily basis. Once the faucet has been used for a long time, it is difficult to unscrew it if it rusts, and when the faucet is replaced, the thread may break due to excessive force.

Another situation is that the inferior zinc alloy nickel-plated faucet becomes brittle due to long-term use. During use, force or bumps may also break due to "inches", resulting in broken water pipes. How do I remove broken wires?

If you want to remove the broken wire in the water pipe, you can use a small saw blade to reach into the water pipe and slowly saw the broken wire open. You only need to cut two openings one centimeter apart on the broken filament and cut off the middle one. Remove the centimeter part, and the remaining broken threads can also be removed.

But this method must be patient, because the saw blade is easy to see the inner line of the water pipe, so you must be very careful to use the saw blade, otherwise the inner line will be damaged, and the new faucet will not work well.

Simple tool wire breaker. In addition to this more difficult method, you can also use a small tool - a broken wire extractor to remove the broken wire from the water pipe. The thread on the wire breaker is the same as the thread on the screw.

The difference is that the thread on the wire breaker is the opposite of a normal screw. As a result, the screws are also rotated clockwise to tighten while the wire breaker is loose. So you just need to find a broken wire extractor in the water pipe that matches the size of the broken wire, go deep into the water pipe, and press hard clockwise until the broken wire is unscrewed.

Due to the use of "reverse wire" design, the broken wire extractor and the broken wire, the broken wire and the water pipe are closely combined together, and will not hurt each other, so that it is not only convenient to take out the broken wire, but also has no effect on the pipeline.

Be sure to close the valve first so that the water can be stopped from flowing out first. Then you can also wrap the leak with waterproof tape first, and then tighten it with wire. If the water pipe is broken, be sure to trim the edges in time, and then repair the water pipe, and you can also find a professional plumber to repair it.

You can turn off the valve of the water pipe immediately, then plug the screw mouth with a plastic bag, and then plug the top of the screw mouth of the water pipe with a towel, so as to block the broken water pipe screw mouth.

At this time, it is useless to block, you should first find the main gate of the water source, and then turn off the valve. At this time, it is enough to replace the old one with the new one.

First of all, we must find the water valve immediately, close the water valve, or use waterproof tape to plug the leakage, which can be very good to block the water in time.

Turn off the water valve of the water pipe first, then plug the leak with waterproof tape, and then tighten the outside with wire.

Introduction: The screws of the water pipes used in the home are often either loose or broken, and many people do not know what to do about this situation, once the faucet is broken, the water will keep flowing out. Some people think that after the water pipe is broken, the first thing to do is to replace it with a new one, but in fact, it is good to plug it.

Today, I will tell you how to plug the screw when it breaks. <>

The broken wire can be removed and connected to a plastic container to prevent water from splashing everywhere, and if you are using an iron pipe at home, cover it with a plastic bag. Put some salt in a plastic container and apply a cotton swab to the gap where the broken wires are connected, then you can see the bubbles, and then use a saw blade screwdriver.

Remove the broken threads and use toilet paper again.

Wipe off the liquid inside. In this way, the faucet can be blocked. <>

Seeing that the screw of the water pipe is broken, most people's first reaction is to quickly replace it with a new one, in fact, I want to tell you that if you find that the faucet is broken, it is very troublesome, because in the case of assembling a new one, the screw cannot be removed, then it will definitely not be installed. Faucets are generally made of alloy, although alloys have a certain anti-rust ability, but if the faucet is exposed to water and air every day, it will still rust, once used for a long time, it is difficult to unscrew and replace the faucet. <>

If you want to take out the broken wire in the faucet, you can use a knife to remove the broken wire in the water pipe, you only need to cut two openings on the broken one centimeter position, and then remove one of them, for example, the rest can also be removed, you must be patient in this process, for impatient people are likely to not be able to do the saw blade, easy to gather to the inner line of the water pipe, so you must use a small blade for sawing, otherwise the inner line will be damaged, and the new faucet will not be used.

You should replace the new water pipe in time, and if you can't get it yourself, you can find a professional plumber to come back and get it. If you don't replace the new water pipe in time, the side that blocks the water pipe will definitely leak after a long time.

After it is broken, you need to put something more sturdy on it, or you can also choose some waterproof stickers, and then choose to connect it with screws after pasting it on, or you can block it.

You can turn off the valve of the water pipe first, and then plug the screw mouth of the water pipe with a towel, or you can directly block it with some waterproof tape.

I think the best thing to do is to connect a quick valve at the break so that the leak can be plugged.

1. Use a blade (1), when the screw of the faucet is partially broken in the pipe, don't worry, and don't smash the wall. (2) Find a small blade and sharpen it into a bevel. Talking (3), the sharpened blade can just be stuck in the pipe and pressed.

4) The returner twists the silver touch left and right, and then the screw stuck in it can be removed. 2. Small saw blade (1) Find a small saw blade. (2) Slowly saw with a small saw blade, but pay attention to start from the direction of the arrow in the figure, do not saw, so as not to affect the strength of the inner wire of the water pipe.

The method of taking out the broken screw of the water pipe is: first insert the extractor into the broken brother screw (insert it tighter), then use a wrench to clamp the quadrangular body at the back of the extractor, and then slowly turn it counterclockwise to take out the screw.

Screws are tools that use objects to rotate the bevel of dust, and at the same time use the physics and mathematics principles related to friction to tighten the parts of the utensils step by step.