Is it possible to use a 60 motor with a 24 battery?

No, because the voltage of the two 24V batteries is only 48V, and the motor cannot be moved. Two batteries plus a 12V battery will match the voltage, but the internal resistance of the battery is different when using electricity, the battery consumption is different when using electricity, and it cannot be charged, so the three batteries can only be removed and divided into 48V and two 24V batteries for charging, and the 12V battery is charged separately with 12 voltages.

No! 60V for 24V power supply, it can't carry the load at all or even can't start.

Any appliance must be powered by a power supply that matches the nominal voltage.

24 60) 2 = 0·16, which is less than 1/6 of the power.

No way. Three 24V batteries are 72V, two are 48V, and neither is accompanied by a 60V motor.

The 60V motor needs to be equipped with 5 x 12V batteries.

In most cases, it is not possible, the voltage is too low, the Y number situation can barely be used, but the speed will be reduced a lot, I have an electric driver is in this case, the nominal voltage is 24V, but I have been using 12V voltage for power supply, it can also be used, but the speed is lower, it can also be used.

Of course not, there is no way to use it.

No, the voltage difference is too much, and the controller is undervoltage protected.

Assorted? 24V can't drive a 60V motor at all! How to match?

No. Because the battery voltage of 48V12Ah is higher than the motor voltage of 24V60W. When the 24V motor is under heavy load, the motor will burn out.

It is possible to divide the 48V12AH battery into two parts. The voltage is reduced by half, and it can be used at 24V.

A 48V battery cannot be used as a power supply for a 24V motor. Otherwise, the motor will be burned out.

No! After changing it, it does not start or runs weakly.

No! 576／900＝0·64。The electric power is only 6 percent.

This is not good, because the voltage is not enough, which will cause many electrical equipment to work poorly.

There are two kinds of common batteries: 6V and 12V, 30V batteries are not, it should be 5 6V batteries in series, I don't know what you are using on the battery, the general voltage is low and will affect the normal use.

It's totally possible, but you have to know in your heart that you don't need low-voltage protection, because if low-voltage protection is used, the voltage is too low for a 64-volt battery at this time, and it may have lost power.

The no-load measured voltage of the battery is higher than the nominal voltage, and the 64V here should actually be a 60V battery, which can be used for the 60V controller.

1. Take the wire: This is a necessary item for the car to take the electricity, do not take two wires to make do, because the instantaneous current of the vehicle at the start can reach 200-600A, and the diesel car even reaches 1000A, if it is calculated, 10 square copper wires can ensure the smooth and safe start, so the car battery.

The cable must be bought of the right brand, the quality of the first, do not try to be cheap. This is one of the must-have items in the car, once the battery is out of power, you can take it out and use it, and you can also help others when you don't use it.

2. Emergency power supply: This is a new type of power bank like a power bank.

The same thing, there are two kinds of lead-acid and polymer lithium batteries, which can help start the vehicle with a loss of electricity, and can also have multi-functional products for lighting, charging mobile phones and inflating cars with inflatable pumps. And it is generally portable, very lightweight, if you have it, you don't have to shout for help to others. Be sure to charge it in time after use and keep it full of power to deal with emergencies.

3. Positive, first connect the positive: first turn off all the electrical equipment on the car, make the key in the OFF position, open the cabin cover to find the battery, there are positive and negative poles written on the battery, generally the red "+" sign is the positive pole, and there are generally two wires, at this time, take out the red one, open the battery cover, pinch the clamp on the head to clamp firmly the positive pole of the battery of the electric car, and the clamp at the other end to clamp the positive pole of the battery of the rescue vehicle. Be sure to connect the positive electrode first, and then connect the negative electrode, do not reverse the order, and do not use the battery clamp to touch anywhere except for the pile head of the electric Zheng Tuan-type pool.

4. Negative connection, negative connection: After the red positive electrode is connected, take out another wire, first clamp the negative pole of the tram battery, the negative electrode is generally black "—" number, and then pinch the other end of the clip, from beginning to end the clip do not touch other places, to clamp the negative pole of the rescue vehicle battery, when the connection will pop out of the electric spark, please don't be afraid, this also shows that you are right. The reason why the negative electrode is not connected first is because the whole vehicle is basically a negative electrode (that is, commonly known as "tie iron"), if the negative electrode is connected first, when connecting the positive electrode, the clip will cause a short circuit and burn the parts on the car when it touches any conductive place in the body.

5. After starting the vehicle, first remove the negative, and then dismantle the positive: after the battery is connected, the rescue vehicle first ignition to charge the battery, and then the no tram enters the vehicle to open the key, at this time the instrument light will be lit up smoothly, and then try to carry out or blind ignition (not more than 5 seconds), if it fails to start smoothly, lightly step on the accelerator of the rescue vehicle, and the speed is kept at about 2500 rpm, and then the no-tram is ignited again, if the starter is no problem, the car has oil in the case of general smooth start, after the non-electric vehicle starts, Remove the negative clamp first, then remove the positive clamp, for the same reason as why the negative pole is followed by the fourth one.

The positive and negative poles of the battery must not be reversed, and the order of assembly and disassembly should be strictly in accordance with the order of first connecting the positive and then the negative, and the first dismantling and then the positive.

When the car battery loses power, it can be connected in series between the two battery du, the positive pole is paired with the positive output line of the battery, and the negative pole is paired with the body to solve the problem of power loss of the electric DAO bottle. The larger the charging current, the greater the charging speed, but the loss of the battery will be greater, and the service life of the battery will be affected over time. When using the charger, it should be ensured that the charging current should not exceed twice the current of the battery, unless the battery is in a hurry, it is best to maintain a constant voltage for the charging liquid.

Generally, the charger above 50A corresponds to 2A in 1st gear, 8A in 3rd gear, and 18A in 4th gear. Usually the battery current is one-tenth of the battery capacity, the battery capacity of the 12V of the family car is about 60 amph, the current is generally 6A, and the charger is most suitable to adjust to 3 or 4 gears. Additional Information:

The precautions for car battery power loss are introduced as follows: not only the owner of the car negligently forgets to turn off the circuit equipment will lose power, but also in the extremely low temperature environment in winter, the car is parked for a long time, and some old cars have approached the battery life, which may lead to the battery loss of the car and cannot catch fire. As long as the car key is screwed to the closed state, all parts of the car are in a state of stopping.

However, in the case of high engine temperature, even if the car is turned off and the car key is withdrawn from the car, the cooling system will automatically start to cool down the engine system. Only when the temperature of the engine system is lowered does the cooling system automatically stop working.

Yes, this kind of motor is used to work at 60 volts.

Because although the battery is nominally 60 volts, the voltage will exceed 60 volts after charging.

The car battery is 24 volts, and the rated voltage of 5 volts can not be used directly, and a DC-DC step-down module can be used, which is sold on the Internet, the wiring is simple, convenient, and can be adjusted, and it can also be used as a mobile phone charger.

No, the charging current of the big car is more than ten A, and you can't use it even if you boost the voltage at five volts, even if you can use it, the charging time will be very long, and you need to buy a special charger.

It is possible to have a transformer, but it is definitely not possible to make it directly.

That's okay. The design of the product and the selection of parts and components completely depend on the conception and choice of the product designer, and there must be reasonable considerations and reasons for choosing what parts. 60 800W electric clearance wheel, if the use of 70Ah battery must have a proper Tong Xuan space, the capacity of the battery to meet the performance of the need to answer, the performance must also meet the provisions of the national standard .......

OK. As long as the voltage of the battery pack is the same and also 60V, it can be used.

The greater the ampere of the battery, the farther the distance of the grinding bucket travel.

However, the travel speed does not increase, or the silver trap is a small increase.

It mainly depends on whether the controller of your electric car is 60 to 72V compatible, compatible can be compatible, otherwise there will be problems, and sometimes the problem of the motor should also be considered.

Add a piece of the same battery in series, change the charger, before adding the battery, everyone is fully charged, so that the power is consistent, do not charge too much in the future, and do not use too much electricity.