Solid wood furniture to be assembled, what are the assembly skills of solid wood furniture?

Solid wood furniture to be assembled, what are the assembly skills of solid wood furniture?

1.Before assembling solid wood furniture, if you are doing it yourself, be sure to read the corresponding instructions for assembling solid wood furniture, and don't toss around. If you are blocked during the installation, it is likely that the operation method is wrong, and do not force the installation, which will damage the solid wood furniture.

When the solid wood furniture is assembled, we can compare the finished furniture with the instruction manual to see if there are any unsuitable places, and then check whether there are still hardware and accessories. Some manufacturers will provide excess hardware accessories, which must be kept after replacement.

2.The installation of solid wood furniture on uneven ground is easy to cause problems such as the tilt of the furniture skeleton, the measurement of the tape measure, the gap between the various parts of the furniture and the humidity of the environment, which also has a great impact on the installation of solid wood furniture. Put the gasket, put the used tools on the gasket in turn, unpack the product, take out the product and put it on the gasket in turn, check whether the product is damaged and whether the parts are complete.

In addition, when solid wood furniture is installed, the floor also needs to be protected with soft materials to avoid scratches, abrasions, etc.

3.We need to assemble the cabinet frame first, put down a side panel, screw the holes with offset printing screws, fix the back brace on the screws we just punched, and then fix the other side panel, and fix the top plate and other panels together according to the drawing, so that the sides and top of our wooden wardrobe have a simple prototype. For cabinet door installation, first we put the hinges of the middle door on the door panel and fix them with screws, then put all the door panels on the hinges of the middle door in turn, and fix all the door panels of the wooden wardrobe on the wardrobe with screws.

Finally, the handle of the wardrobe can be screwed to the handle door panel. After the initial furniture installation is complete, the verification and adjustment of the furniture installation is also of paramount importance. The main aspect of the inspection is whether the pieces of furniture are firm and tight together, and whether there are gaps.

Whether the drawer pulley slides smoothly, whether the board surface is tilted and deformed, etc.

Fully furnished:

The overall packaging needs to be transported as a whole, and the handling only needs to be carried into the customer's home, which basically does not need to be installed, and the handling seems simpler. However, it will take up a lot of space in transportation, and a large truck cannot transport many pieces, and often have to fight wooden frames. Even if the wooden frame is hit, there are often bumps, and maintenance requires a skilled master to rest.

And because it is a complete assembly, it cannot be installed with a single part, and if the structure is damaged, it needs to be returned to the factory for repair, and the maintenance cost is greatly increased, and it is more dependent on the local maintenance and after-sales team. (The installation of complete furniture requires professional tools and environments, such as F-clips, straps, flat construction surfaces, etc., some conditions are not available in the customer's home).

In terms of shape, the whole furniture will be more rounded, with more varied lines and more design details than assembled furniture. Assembling furniture is generally connected by 3-in-1 or screws. The shape is square and conventional.

The whole assembly can be connected with a high technical requirement such as mortise and tenon joints.

When assembling, be sure to use professional tools to assemble, and also pay attention to the details, don't assemble the wrong one, and also assemble according to the drawings, because this can save yourself a lot of unnecessary trouble, but I think the most important point is that when assembling solid wood furniture, you must pay attention to the operation problem, and don't stain the solid wood furniture.

When assembling again, you must assemble according to the assembly drawing, you must be careful when assembling, so as not to bump into some places, ask the relevant people when assembling, and work with other people when assembling, find professionals to install, and handle it gently when assembling.

When assembling, you must study the manual, and spread a layer of blankets or mats on the ground to ensure that the home is in a stable state.

It is necessary to read more instructions, ask more merchants, measure more sizes, compare more, and use the right tools to carry out on a flat ground.

Assembling furniture is now more common, it is mostly used for panel furniture, so how to install assembled furniture? In addition, how to assemble furniture to disassemble? Let's take a closer look at it.

Panel furniture is widely used in modern home life, and has a non-negligible role in improving the visual effect of the entire space.

1. Prepare the required three-in-one hardware, such as: eccentric wheels, screws, embedded parts, etc., and first make holes in the plate;

2. Punch the embedded hardware into the A plate;

3. Check on the B plate corresponding to the A plate, and select the punching method and position;

4. Install the eccentric wheel and screw and confirm their position;

5. Lock the eccentric wheel and screw;

6. On the eccentric wheel, it will be marked with "+" and the "+" direction to tighten the eccentric wheel, and to press the "-" direction to tighten the eccentric wheel is to loosen;

7. It can be judged whether it is locked according to the cross situation on the eccentric wheel;

8. Screw the screw into the embedded parts;

9. Connect the B plate and A plate together through connectors, and check whether the position of the screw rod and the two plates is correct after connection;

10. Put the eccentric wheel into the hole, and the eccentric wheel can be correctly put into the hole if the position is right, and it will not be higher than the plate or lower than the plate, which is the correct punching depth;

11. Tighten the connector in the correct direction.

The assembly of assembled furniture needs to be based on relevant professional steps, and in terms of disassembly, the requirements for experience and practical hands-on operation ability are also relatively high, so users should first consider whether they can meet the requirements of assembly and disassembly when purchasing furniture that needs to be assembled by themselves, and combine relevant knowledge, according to the instructions of the manual, such as panel furniture disassembly - three-in-one connector installation steps, judge the type of furniture they need to disassemble, and operate patiently to achieve the purpose of disassembly.

Assembling furniture is now more common, it is mainly used for panel furniture, it can be disassembled after installation, for renters, it will reduce the changes brought about by moving, the installation of each furniture is different, how to assemble furniture Let's take a closer look at the installation process of each type of furniture.

How to assemble and install furniture?

Panel furniture is widely used in modern home life, and the impact on improving the visual effect of the entire space is negligible. In the disassembly and assembly of panel furniture, the disassembly and assembly of hardware is the most critical step. What is the disassembly procedure for panel furniture hardware?

1.Prepare the required 3-in-1 hardware, such as eccentric wheels, screws, plug-ins, etc., first punch holes in the board;

2.Drive the embedded hardware to board A;

3.Check on the B plate corresponding to the A plate, and select the stamping mode and position;

4.install the eccentric wheel and tighten it and confirm its position;

5.locking eccentric screws and screws;

6.On the eccentric wheel, press "+" and "-" to tighten the eccentric wheel in the "+" direction, and press the "-" direction to tighten the eccentric wheel;

7.It can be judged whether it is locked according to the cross on the eccentric wheel;

8.Screw the screws into the embedded part;

9.Connect the B board and A board together through the connector, and check whether the position between the screws and the two boards is correct;

10.Put the eccentricity into the hole, you can put the position of the eccentric wheel into the hole correctly, not higher than the plate, not lower than the plate, this is the correct drilling depth;

11.Tighten the connector in the correct direction;

The assembly of assembled furniture needs to be based on relevant professional steps, and when it comes to disassembly, the requirements for experience and practical operation are relatively high. Therefore, when users buy furniture that needs to be assembled by themselves, they should first consider whether it can meet the assembly and disassembly. Requirements, and together with the knowledge of Xiangming Land Customs, follow the instructions in the manual, such as panel furniture disassembly - 3-in-1 connector installation steps, determine the type of furniture you need to disassemble, and patiently operate to achieve the purpose of disassembly.

How to assemble furniture?

Some special connectors can realize the horizontal connection of two boards, and the three boards are connected alternately, which are generally used for MDF, high-density board, and particleboard.

The 3-in-1 consists of three parts: the 3-in-1 is equivalent to the nail groove structure of traditional woodworking, they are eccentric heads (also known as eccentric nuts, eccentric wheels, eccentric pieces, etc.), connecting rods (bolts) and pre-inserted nuts (commonly known as plastic particles, the advantages of 3-in-1 connectors are as follows:

1.Pre-inserted nuts: dedicated to reinforcement; Connecting rods: connect only, eccentric head: solves the problem of locking between plates. The combination of bolts, bolts and eccentric components makes the trinity a strong connection.

2. The 3-in-1 connection can be removed many times, which is one of the advantages of panel furniture.

3. Hidden from the outer surface, you can't see the three-in-one Lianjia acacia bender.

4. Three-in-one connection, reduce the use of adhesive. More environmentally friendly.

The assembly and installation of furniture is a very important work in the process of decoration and moving, which is related to the overall effect of the home environment and the comfort of use. The following Luban will give a detailed introduction to the assembly and installation skills of furniture.

Read the instructions and prepare the tools carefully Before assembling the furniture, be sure to read the instructions carefully to understand the assembly steps of the furniture and the tools required. At the same time, it is necessary to prepare the required tools in advance, such as screwdrivers, wrenches, electric drills, etc. This makes the assembly work more efficient and smoother.

Clean and tidy up the work areaBefore assembling furniture, clean and tidy up the work area. Remove debris from the floor and make sure there is enough space for assembly operations. In addition, the furniture parts should be arranged in order to make it easy to use.

Read the assembly steps carefullyWhen assembling furniture, read the assembly steps carefully. Follow the order on the instructions to make sure you don't make mistakes at every step. If you have any questions about a certain step, you can first consult the relevant slag return information or consult a professional.

Pay attention to the material and quality of the furnitureWhen assembling furniture, pay attention to the material and quality of the furniture. If the furniture is made of solid wood, special attention should be paid to the appropriate amount of force when tightening the screws to avoid damaging the furniture. If it is panel furniture, pay attention to the reasonable lap connection method to ensure that the connection is firm.

Before the formal assembly, you can try the assembly once to check whether the connection between the parts is suitable for imitation beams, and whether there are any omissions or errors. In this way, problems can be identified and solved in a timely manner, avoiding difficulties during formal assembly.

Pay attention to the stability of the furnitureWhen installing the furniture, pay special attention to the stability of the furniture. The stability of furniture is directly related to the safety and comfort of use. During the assembly process, make sure that the screws at each connection are tightened and that the joints are not loose.

If stability is found to be insufficient, support or reinforcement screws can be added.

Avoid using excessive forceWhen assembling and installing furniture, avoid using excessive force. Especially when tightening the screws, pay attention to the appropriate force. Excessive force may damage the parts of the furniture or cause unnecessary trouble.

Pay attention to moisture and insect protectionWhen installing furniture, some furniture needs to be placed on the ground, which is susceptible to moisture and insect infestation. Before installing furniture, you can put some moisture-proof and insect-proof mats on the ground to avoid damage to the furniture.

Tidying and cleaning the work areaAfter the furniture assembly and installation is completed, the work area should be cleaned and sorted out in a timely manner. Clean up excess packaging materials and put tools in place to ensure a clean and organized work area.

Summing upThe assembly and installation of furniture is a job that requires patience and skill, and only correct operation and careful handling can ensure the safety and stability of the furniture for failure. Hopefully, the above tips will be helpful to you.

The assembly of the manuscript chain has the following characteristics:

The parts and components that assemble furniture are generally small, easily lost or confused, and need to be carefully inspected and checked.

Some tools and materials such as screwdrivers, screws, washers, glue, etc., are required to be used to assemble furniture, which need to be prepared.

The parts and components of the assembled furniture generally need to be assembled according to the instructions of the drawings or instructions, and the instructions need to be read carefully and understood.

Assembling furniture requires attention and avoiding errors or omissions in the installation of parts and components, which could affect the longevity of the furniture.

Proper installation steps for assembling furniture:

Have all zero-key annihilators and parts ready and check them carefully.

According to the installation instructions, the various parts and components of the furniture are sorted and sorted.

According to the installation instructions, assemble the furniture step by step from the bottom to the top, from the inside to the outside, in order.

During assembly, take care to protect the surfaces and edges of the furniture to avoid scratches or abrasions.

During the assembly process, pay attention to the balance and stability of the furniture to ensure that it is safe to use.

After the assembly is completed, check whether the various parts of the furniture are fastened, whether the surface is flat, and adjust in time if there is a problem.

Clean up the trash and dust generated during the installation process and make sure the furniture is clean and tidy.

If you need installation and maintenance services, you can go to the Luban Daojia platform to find professional services.