-
1. Before the furniture is installed, the packaged accessories should be taken out, and then the screw hole that needs to be installed three-in-one must be locked into the board.
2. After locking all the screws of the installation 3-in-1 to the board, you can start assembly. Note: If there are too many boards, it is difficult to distinguish which piece is and which piece is assembled, then, all drawers should be installed first, because the drawer installation is the simplest, and the board accounts for a lot of proportion, then the rest is the side plate and the back plate, the top plate, the bottom plate and some shelves.
3. After figuring out the side plate, the back plate, the top plate, the bottom plate, and the shelf board, the others are some connecting plates, generally speaking, the bottom plate is installed first, the bottom plate can be installed after the middle side plate, and then the rear side plate is installed and then the top plate is installed and finally the side plates on both sides are installed, then the main body of the cabinet is up, which is the layer board and clothes rail, and finally the door can be installed.
-
1. Place the bottom plate. When you are ready, you can start to install the floor of the wardrobe, and the floor must be clean, as we all know that the floor of the wardrobe is more difficult to clean.
2. Fix the frame. Install the side panels and back panels according to the structural parts of the wardrobe panels, and fix the frame of the body first.
3. A herringbone ladder is required to install the roof, which will be more convenient, after all, the wardrobe is generally more than 2m high, and then the roof house is fixed with rivets on the top surface.
4. Install shelves. The partition is the board of the wardrobe compartment space, which is carried out after the top plate is installed, as long as the shelf is placed in a fixed position and fixed, special attention is paid to each partition to be suitable, the partition and the back panel, the side panel are to be fixed.
5. Fix the door rail. Then it's time to start installing the door rails on the top and bottom edges of the wardrobe, preferably in a lightweight and strong alloy material.
6. It is relatively simple to install the clothes rod, lay the fixed rivets, and pay attention to the balance on both sides.
-
The general steps for wardrobe installation are as follows:
Prepare the main panels, panels and other accessories of the wardrobe.
Start to install the side panels and back panels of the wardrobe, the side panels and back panels of the wardrobe are fixed by the round pendant of the wardrobe, and the side panels and back panels need to be assembled first.
Install the top and bottom plates of the wardrobe and secure them.
Install wardrobe trim strips and other accessories such as drawers, trouser racks and handles.
Install the wardrobe door.
Adjust the hardware of the wardrobe, pay attention to the screws of the wardrobe should not be fixed too tightly, so as to avoid the situation that the screws are not fixed firmly and the wardrobe is loose.
After installation, it is necessary to keep the wardrobe dry and clean as soon as possible to avoid moldy or damp orange residue in the wardrobe.
Hope the above information is helpful to your question.
-
As the economic situation improves, people's consumption has also increased. Now install a wardrobe should also pay attention to beauty, unlike before just install a wardrobe, a wardrobe is beautiful or not depends largely on the installation, and the installation of this link is very important, how to install the wardrobe? These five steps of wardrobe installation must be memorized.
So here's how to install the wardrobe.
One. Wardrobe assembly steps
1.Installing the base plate: Before installing, we must first choose its base plate, first of all, to install.
2.Installing the Backplate: After the bottom plate is installed, we should follow the installation of the backplate. At this point, it should be noted that the backplate and backplate need to be kept at a right angle of 90 degrees so that the force is uniform to avoid prevention. The mistake is to tilt the front and so on.
3.Installing the side panels: The next thing we want is that the side panels of it are mounted, and it should also be at a 90-degree right angle to the back panel. If there is a slight deviation during installation, be sure to correct it in time.
5.Install the rest: then we can install the cabinet doors, drawers and clothes one by one. When these parts are installed, the entire wardrobe is installed.
Two. What are the precautions for wardrobe installation
1.To install a late rental cabinet, you need to pay attention to the size of each plate.
Before installation, we need to know exactly the size of each part of the plate, know exactly which part is this and which part is it, so that there is no confusion.
2.Attention should be paid to its safety during installation.
Since the body of the wardrobe is wooden and has a certain weight, we must pay attention to safety when we are in the installation, avoid being injured by bruises, and also avoid damaging the board.
There are many precautions for wardrobe installation, and we must change its command installation to installation, so that the process of installation can be smoother, avoid rework, etc.
-
The steps for Luban to install the wardrobe are as follows:
Open the box and remove the packing accessories.
Put the bottom plate of the wardrobe on the ground, and slowly pull out the bottom plate in the packing box with a knife to prevent the bottom plate from being damaged.
Take out the side panels and back panels of the wardrobe, dock the side panels and back panels together, and fix them with self-tapping screws.
To install the wardrobe door, the general wardrobe door is integral, and two side panels need to be connected and fixed with self-tapping screws.
Install the top plate, pay attention to distinguish the front and back of the roof, only the back has a self-tapping mounting hole, but the front structure is more complex, and it needs to be connected with the cabinet door.
To install the baseplate, place the baseplate directly at the bottom of the cabinet, press down, and install the screws.
Install the laminate and the middle wheel bucket spacer, and the installation sequence is carried out from top to bottom, from left to right, sequentially.
Check whether each part is fixed firmly, open and close the cabinet door, and see if there is any stuckness.
-
1. Preparation stage 1, the material arrival is more formal furniture manufacturers, and the board is generally packaged in cardboard when it is transported to the site. After unpacking, check the plates and hardware. 2. The fixing screws are generally left with nail holes according to the design drawing, and the workers on the site fix the screws with special tools.
3. Since the wardrobe is placed against the wall, a piece of the side panel should be sawed off at the position of the baseboard. Place it to see if it fits. Second, the installation stage 1, the floor where the bottom plate of the wardrobe is placed should be cleaned in advance, because it will be very troublesome to clean it after installation.
2. Install the side panels and back panels of the wardrobe according to the grooves on the plates, and adjust the positions between the boards. 3. It is best to prepare a stool for climbing on the installation site, and the roof should be raised and placed, and then fixed with rivets. 4. Install the shelfPut the shelf in the place where the screws have been knocked in advance, and then fix it.
Pay attention to adjusting the fixed position of the shelf, back and side panels. 5. The fixed door rail is installed on the top and bottom edge of the wardrobe, and the alloy material of the door rail is better, light and firm. 6. Install the clothes rod and fix the rivets in the reserved position and install the clothes rod.
Pay attention to balance on both sides. Third, the finishing stage 1, the installation of the door leaf two sliding doors to be attached to the position of the guide rail installation, first fix the door leaf and then fix the bottom of the guide rail, so as to avoid the phenomenon of the door leaf falling off in the future. 2. After all the adjustments and improvements are installed, do a "comprehensive inspection" of the wardrobe, and adjust it in time if there is a deviation.
3. Complete the acceptance and finally do the acceptance of the wardrobe: shake the cabinet to see if it is firm and whether the details are in place.
Preparation stage. The material is present.
For more formal furniture manufacturers, cardboard packaging is generally available when the panels are delivered to the site. After unpacking, check the plates and hardware. >>>More
PPR water pipe is one of the most commonly used water pipe materials in home decoration, the following are several of the most common installation methods: First, first get the line right, and then groove on the ground, I think it is better to let the plumber do it, because at least people are professional, in case the water pipe leaks is not very good. Second, from the connection of the PPR pipe: >>>More
Titanium sliding door.
It can also be called the Thai technology sliding door, which is a door that can be moved left and right and easy to install, in order to facilitate us to open, do not have to lock, and can block the air conditioning and odor, this titanium alloy sliding door is most suitable for us on the balcony at home. >>>More
The combined wardrobe is the kind of wardrobe made of a wall to be closed, the size of the wardrobe can be determined by the length of the wall, some people call it a wall-in wardrobe. >>>More
Like the toilet seat, it is also very simple according to the method, you can screw the buckle under the toilet lid to him, and then buckle the cover into it, so that the toilet lid is installed.