How to disassemble and clean the air conditioner, how to disassemble and clean the air conditioner

How to disassemble and clean an air conditioner?

1.Remove the panel of the air conditioner, remove the wind deflector together, disassemble the electrical control box, and remove two screws.

2.Disassemble the water tank, when disassembling the water tank, remove the stepper motor of the wind deflector, and the water tank can be pulled out directly by hand.

3.Remove the cover on the motor box, leak out the motor shaft and the wind wheel shaft, loosen the screws of the motor shaft and the wind wheel shaft, and pull out the motor box and the wind wheel together with some force.

4.After the disassembly of the wind wheel is completed, clean the filter. If there is too much dust, you can rinse it with clean water or use a professional air conditioner cleaner.

There are generally 2 parts to air conditioner cleaning.

First: the air conditioner shell and filter, which can be done with a rag and soapy water, you who do housework, must understand;

The second part is to clean the heat sink inside, this is the key, because this piece is a concentration camp of dust and bacteria, and it is also the innermost part of the air conditioner, it is difficult to clean, it must be cleaned with a professional air conditioning disinfectant, the operation method is very simple, the high-pressure nozzle of the disinfectant is against the heat sink, and spray it evenly, and then reset the cleaned filter screen and shell, turn on the refrigeration mode, and after a while you can see that the dirty things are flowing away with the drain.

The air conditioner is disassembled and cleaned** as follows:Preparation tools: Gridg Heli air conditioner, air conditioner cleaning agent.

1. First unplug the power supply of the air conditioner, and press the two sides of the air conditioner panel to open the panel.

2. Remove the air conditioner filter, brush the filter with clean water, ventilate and dry.

3. Spray the air conditioner cleaner back and forth evenly at a distance of five cm from the air conditioner radiator, finish spraying, and wait for 15 minutes for the cleaner to fully dissolve.

4. Install the air-dried filter back to the empty sail leather tone, close the panel, plug in the power supply and turn the air conditioner into the refrigeration mode to work for 30 minutes, which can discharge the sewage when cleaning the air conditioner, and turn off the air conditioner after 30 minutes, and the air conditioner can be cleaned by turning it off.

1. First of all, in order to prevent electric shock and leakage, you need to turn off the power socket, or you can directly unplug the socket, which is very important;

2. Then open the shell of the air conditioner upwards, with a very light force, special attention should be paid to the fact that if you find that it is not easy to open by hand, you can use a screwdriver to help, do not use brute force, you must master the skills, otherwise it is easy to damage the shell of the air conditioner;

3. After opening the shell, the inner shell is raised above the air conditioner, and the air conditioner shell can be automatically stuck and fixed, so you don't have to worry about falling off; At this time, you can see that there is a plastic air conditioning filter inside, which is the part that loves to hide dirt and dirt;

4.You only need to gently push the filter up with your hand, and then remove the filter screen;

5 Put the strainer in the basin and rinse it directly with water.

6. Then add an appropriate amount of warm boiling water to the basin and soak for an hour, as shown in the figure below;

7. After an hour, clean the filter with clean water;

8. Finally, put the cleaned filter on the balcony to dry.

After the air conditioner is used for a long time, a lot of dirt and bacteria will accumulate inside, which will not only affect the operation effect of the air conditioner, but also reduce the service life of the air conditioner, so it is necessary to disassemble and clean the air conditioner regularly, so how to disassemble and clean the air conditioner? Let's learn together.

1. If you want to disassemble the air conditioner for cleaning, then you should unplug the power plug of the air conditioner first, so that the air conditioner is in a safe state of power failure. Then prepare relevant disassembly tools and cleaning tools, such as: special air conditioner cleaner, rags, high-pressure water guns, screwdrivers, etc.

2. When disassembling and cleaning the air conditioner, it must be operated in strict accordance with the disassembly and cleaning steps introduced in the instruction manual of the air conditioner. Each air conditioner will be equipped with an air conditioner instruction manual, which will generally introduce in detail about the disassembly and maintenance of the air conditioner, as long as the operation is carried out according to the operation steps introduced in the manual, there will generally be no problems.

3. When disassembling and cleaning the air conditioner, the shell and filter of the air conditioner should be removed first. When disassembling the air conditioner shell, you should buckle both ends of the air conditioner shell with both hands at the same time, and then pull the air conditioner shell out of an angle with a little force, and then gently buckle the two buckles inside, and then you can remove the air conditioner shell.

4. Next, the filter screen should be disassembled, the filter screen is generally stuck by several card slots, you should first push the filter screen up, let the lower end of the filter screen out of the card slot, and then gently drag the filter screen down, and generally you can remove the filter screen.

5. Then you should use a special air conditioner cleaner to clean the shell and filter of the air conditioner. When cleaning the filter, you can use a soft brush to continuously clean it, but you must be careful not to bend the filter. Then use a high-pressure water gun to rinse the casing and filter of the air conditioner.

After the filter is cleaned, it should be placed in a ventilated area to dry.

6. When cleaning the inside of the air conditioner, you can use a watering can cleaner for cleaning. First spray the watering can cleaner inside the air conditioner, and the watering can cleaner will produce a lot of foam, attached to the inside of the air conditioner, then you need to wait for about five minutes, let the foam dissolve the dust and dirt accumulated inside the air conditioner, and then use a rag to wipe the inside of the air conditioner continuously, and finally use a scraper to clean up the residual foam.

7. After the inside of the air conditioner is cleaned, install the air conditioner filter back, and when installing, do not install it in the wrong direction, and install it correctly according to the position of the buckle. Then install the air conditioner shell back, and finally use a rag to wipe the air conditioner shell clean.

The above is a detailed introduction to how to disassemble and clean the air conditioner, if you want to disassemble and clean the air conditioner, you can learn more about it, it is recommended that you should operate according to the disassembly and cleaning steps introduced in the instruction manual of the air conditioner, so as to avoid problems.

1. First of all, open the front cover of the air conditioner: pick both ends of the panel with both hands at the same time, and then pull the panel apart at an angle with a little force.

2. After opening the outer cover of the air conditioner, there are often two buckles inside, and it is necessary to gently open the outer cover to fully open. Then it is to take the filter, the filter is relatively easy to take, but it is stuck by a few card slots, first push the filter up, and then gently drag the filter down after the card slot.

3. Then carefully rinse the filter with clean water several times, you can scrub it with a soft brush several times, and finally dry it in a ventilated place until it is dry. Be sure not to bend the filter when cleaning, although it is elastic, but the plastic one can not withstand bending.

4. When installing the filter, you need to pay attention to the wrong direction. It is very important to install it correctly according to the bayonet position above. After installing the filter, cover the panel, press it hard, and the installation will be successful when you hear a "click".

Based on the respondent's experience;

1. First of all, turn off the electric power source socket. It is best to unplug the socket directly, which is very important to avoid electric shock and leakage accidents.

2. Open the two ends of the shell of the water air conditioner, with a small amount of force, if you can't open it by hand, you can use a screwdriver to help, you need to master the skills, otherwise it is easy to damage the shell.

3. Open the shell, and then know that the stove will lift the shell above the water air conditioner, which can be automatically stuck and fixed, so you don't have to worry about falling off and dressing up.

4. You can see that there are 2 plastic frames inside, one on the left and one on the left. Inside this frame is the fiber mesh, which is the part that filters the air conditioning air and hides the dirt the most.

5. Gently push up with your hand, remember that a frame has 2 places to fix, and you need to push up on both sides. Remove the filter.

6. Take it to the toilet or have a water source. place, place on the ground, rinse directly with water, and then gently brush a few times with a brush.

7. Finally, use laundry detergent, or add with detergent, and then brush with a brush a few times, and finally it is very clean, use a clean dry rag to absorb the water, and there is no need to deal with it too dry, there is no problem.

8. Finally, according to the above method, in turn, push down, stuck, and finally close the water air conditioner shell is completed.

Hope it helps!