How to disassemble the washing machine for cleaning, how to disassemble and clean the washing machin

After a long period of use, dirt will accumulate in the washing machine, and if it is not cleaned for a long time, it is easy to breed bacteria and even produce odors. So how to disassemble and clean the washing machine? How much does a washing machine cost?

In the following sections, we will introduce you in detail how to clean the washing machine.

1. How to disassemble and clean the washing machine.

1. Tool preparation.

Medium and large Phillips screwdrivers, adjustable wrenches, rags, basins, etc.

2. Disassemble the washing machine.

1) First use a large screwdriver to remove the washing machine wheel, and then choose a suitable tool to loosen and remove the screws under the wheel;

2) After that, remove the four screws on the middle frame of the washing machine, and then lift the middle frame from the front end to the back, so that the inner cylinder of the washing machine can be seen;

3) Next, loosen the screws on the upper edge of the contents and remove the cover, after which you can pull out the inner cylinder.

3. Washing machine cleaning.

You can soak the inner cylinder with a special cleaning agent for the washing machine for half an hour, and then clean the inner cylinder of the washing machine with a gentle cloth or brush.

Reminder: The above is the disassembly and cleaning method of the inner drum of the automatic drum washing machine, because there are many types of washing machines on the market, and the disassembly methods of different types of washing machines are different, and the specific installation and disassembly instructions should be carried out. Also, when disassembling the washing machine, pay attention to disconnect the power supply.

Second, how much does the washing machine cost.

The washing machine is related to the type of washing machine, because some washing machines are not easy to disassemble, so it is more troublesome, and the more expensive it is to disassemble and wash. The cleaning costs for all types of washing machines are as follows:

1. Parallel bar washing machine: about 20-30 yuan;

2. Automatic washing machine: about 30-50 yuan;

3. Drum washing machine: about 80-100 yuan.

There is also the washing machine cleaning in different places** is also different, and the specific ** should be determined according to the local situation.

In fact, the most cost-effective way to clean the washing machine is to do it yourself, you only need to buy some special detergent for the washing machine, and then disassemble and clean the washing machine according to the washing machine disassembly and cleaning method introduced above. Here are a few good washing machine detergents

1. The old housekeeper washing machine detergent detergent 375g*3 boxes, about 35 yuan;

2. Green umbrella drum washing machine detergent detergent 125g*12 bags, about 40 yuan;

3. German domol washing machine detergent detergent 60 capsules*1 box, about 90 yuan.

3. Washing machine cleaning method.

There are two main ways to clean the washing machine, one is to ask a professional cleaning personnel to disassemble and clean it, and the other is to use detergent to clean it yourself. Next, we will introduce the second washing machine cleaning method in detail.

1. Washing machine barrel cleaning.

Put the water in the washing machine to a high level, then pour in an appropriate amount of detergent, then install the normal working mode of the washing machine, turn on for 5 minutes, the purpose is to let the detergent and water fully dissolve, and then turn the washing machine.

How to disassemble and clean a semi-automatic washing machine.

The first thing to do before washing the washing machine is to cut off the power.

Washing machines are an indispensable helper in our lives, but many people don't know how to clean them! The washing machine that has not been cleaned for a long time is dirtier than the toilet, and it must be disassembled and washed if you want to clean it thoroughly.

1. Disassemble the entire workbench above, there should be 2 or 4 screws, unscrew.

2. Some washing machine screws may be in the back, and the front can be lifted to tilt it. The main thing is that the back is the wire, so be sure not to damage the power cord.

3. Loosen the screws and push them forward slightly, and the panel can be picked up against the wall.

4. Use a large Phillips or flathead screwdriver to disassemble the wave wheel, unscrew it, and take the wave wheel out of the barrel. There is a spacer underneath the wave wheel.

5. Dismantle a big nut, this is recommended to find a special tool, otherwise the whole barrel will fall if it is not tightly loaded in the future. Be sure to tighten it when you put it back on, as tightly as you want.

6. The nut is dismantled, and there is a cross-section L-shaped fixed sleeve below, which cannot be lost.

7. Then the whole bucket can be taken out.

Use a screwdriver to remove the lid of the washing machine, and then remove the screws of the washing machine's wave wheel. Take out the stainless steel inner cylinder of the washing machine. Wash them one by one and put them back in place.

1. Open the washing machine cover with two rivets on the left and right sides to fix the washing machine cover, and remove these two plastic rivets with a screwdriver.

2. Remove the screws of the washing machine. Take out the stainless steel inner cylinder of the washing machine.

3. Clean the inner wall of the washing machine thoroughly, generally this inner wall will be very dirty, and it should be cleaned well.

4. Take the stainless steel bucket of the washing machine aside to clean it.

5. Put the cleaned stainless steel barrel back in place and finish.

Notes:1. After disassembling the lid of the washing machine, do not throw the screws around, and install the screws in place after cleaning.

2. Before dismantling, you can heat the water with vinegar and laundry detergent for 3 hours to facilitate cleaning.

Answer: It is definitely not possible to disassemble and wash, because it cannot be opened. Unless you are an old-fashioned washing machine, the current washing machine is a high-tech product, and if you want to disassemble it, it is destroying, and you can't put it back when you disassemble it. There are items on the market that sell washing machines, which are not expensive, and they can be cleaned by putting them in the washing machine and turning around a few times like washing clothes in ordinary times.

If it is a washing machine, first remove the water inlet pipe, disassemble the upper cover, then remove the wave wheel, remove the retainer between the inner barrel and the outer barrel, remove the screw between the inner barrel and the clutch, you can take out the inner barrel, you can wash it, if the drum is one, finally find a professional.

1. Disassembling and cleaning the washing machine is suitable for the washing machine, because the internal structure of the drum washing machine is complex, this method is not used. 2. Before disassembling and cleaning the washing machine, you need to turn off the power of the washing machine and prepare different types of screwdrivers. 3. Open the upper cover of the washing machine, and then remove the screws connecting to the upper cover, then you can lift the upper cover of the washing machine and take it off.

4. Then choose a suitable screwdriver and remove the screws of the washing machine, so that the stainless steel liner of the washing machine can be successfully removed. 5. Use a brush and detergent to thoroughly clean the inside of the washing machine, this inside is the dirtiest, covering all kinds of hair, dander and dirt of the clothes, which needs to be carefully cleaned, and finally rinsed with clean water. 6. Then clean the stainless steel barrel of the washing machine, comprehensively clean the inside of the stainless steel surface, and then put the cleaned stainless steel barrel back in place, and the screws are good.

7. Finally, install the lid of the washing machine back, and screw the original screws back in the same way as the removal steps.

1. Disassembly of the frame.

1) Remove the fixing screws of the workbench and the box, and put the workbench vise on the box.

2) Unloading'Three fixing screws on the lower workbench and control panel to loosen the workbench and control panel.

2. Disassembly of the computer board.

1) Lift the outer edge of the control panel upwards with your hand so that it is detached from the frame.

2) Unscrew the screws, take out the waterproof plate first, remove the circuit board, and unplug the wire from the computer board.

3) Loosen the water level switch, install the fastening screws of the switch and the power switch, and remove the switches one by one.

3. Disassembly of the wave wheel.

1) Use the cross to loosen the wave wheel screw, unscrew out 10cm and then lift the screw by hand, and the wave wheel can be lifted. If you can't lift it, you can gently pry it up from a few positions on the edge of the wave theory with a flat mouth, and then lift the screw head.

2) When disassembling the wave wheel, if it is really impossible to remove it, you can first disassemble the V-belt and clutch pulley, and then take the wave wheel and hold the spring. For general clutches, as long as the clutch sleeve is removed, the inner shaft of the clutch can be easily opened, and then the wave wheel can be lifted together with the washing shaft.

Cut off the power! The washing machine was dismantled in situ, as power and drainage were also needed later. Use a screwdriver to loosen the screw counterclockwise, remove it, and lift the raised blade up with both hands. If there is water that is slippery, it is easy to dry it and lift it again.

The back of the removed blade is like this, it has been cleaned once before, and it is still so dirty, when I take it off for the first time, I can't bear to look at it!

After the blade is removed, there are 4 screws here, I can use a screwdriver to unscrew it, most of them need a wrench to unscrew, if there is a hex wrench of the same size, it is even simpler.

There is one such screw on the left and right sides of the outside of the washing machine, pry open the shell, and unscrew the screw. There are 2 more in the back, which are also unscrewed.

After unscrewing the 4 screws on the outside of the upper cover, you can lift the upper cover, so be very careful at this time! The upper cover cannot be removed completely, it can only be flipped back, so one such support is needed at the back!

The cover can't be completely removed because there are water pipes and wires connected, and we don't want to mess with these wires, just keep it in this state. At this time, you will find that there is a lid on the barrel, unscrew 4 screws, lift 4 small buckles, and easily remove it.

If you unscrew the 4 screws under the blade in the 3rd step, then shake the inner barrel, and the inner barrel will be raised, we usually see the inner wall of the inner barrel, thinking it is very clean, in fact, the outer wall is very dirty, and the bottom!

After the inner bucket is removed, you can see this dirtiest outer bucket! I've washed it once before, and I'm sure the first time you took it apart, it was many times dirtier than I did! Don't take off the outer barrel, because there is a drain pipe and a power cord connected underneath, which is more complicated, and we just disassemble and wash it without moving!

Pour water into a bucket and brush with a brush or toothbrush. After brushing, you need to turn on the power and choose dehydration directly, and the sewage can be discharged, and it will be washed after several repeats!

That's it after washing! In order to make your clothes cleaner, let's do it!!

How to disassemble and clean the washing machine is as follows:

1. Find a suitable Phillips screwdriver, and then unscrew the screws on the middle base.

2. When the screws are fully loosened, unscrew them by hand, so that the base is loose and taken out.

3. When taking out the base, it is best to tilt it and take it out at the place with the largest diameter in the washing machine barrel, otherwise it will be stuck and cannot be taken out.

4. After taking out the base, you can see that there are a lot of dirty things in the inner cylinder, and wipe it clean with a damp rag.

5. The taken out base can be directly rinsed with running water, pay attention to the front and back sides.

The washing machine has been used for a long time, and there will be a lot of bacteria and various stains left in the wax head, which is really very dirty

1. First of all, open the cover of the washing machine, and see that there are two rivets on the left and right sides to fix the lid of the washing machine, and the two plastic rivets are removed with a screwdriver. Then lift the lid of the washing machine. Take it down.

2. Remove the screws of the washing machine. Take out the stainless steel inner cylinder of the washing machine.

3. Then clean the inner wall of the washing machine thoroughly, generally this inner wall will be very dirty, and it should be cleaned well.

4. Take the stainless steel bucket of the washing machine aside to clean it.

5. Then put the cleaned stainless steel barrel back in place and put the screws on well.

6. The next step is to install the lid of the washing machine, which is the same as the removal step, and put the screws on.

The washing machine needs to be disassembled and cleaned regularly, if the clothes are not dismantled to be cleaned, the stains and pollutants in the air will remain in the washing machine drain pipe, clogging the drainage system, and the clothes will become more difficult to clean.

Specific steps: 1. Preparation: a hard support, two screwdrivers, a cross and a washing machine cleaner, and wear protective gloves during disassembly.

2. Quietly grind the foundation and open the cover of the washing machine, and see that there are two rivets on the left and right sides to fix the lid of the washing machine, and the two plastic rivets are removed with a screwdriver. Then lift the lid of the washing machine. Take it down.

3. If there is water that will slip during the removal of the blade, wipe it dry and then lift it. After the blade is removed, there are four screws on the back, which can be unscrewed with a screwdriver, most of which require a wrench to unscrew, and can also be used if there is a hex wrench of the same size.

4. After unscrewing the 4 screws on the outside of the upper cover, you can lift the upper cover, if the upper cover can not be completely removed, you can only turn it back and open it, and you need a support behind it.

5. There is a lid on the inner barrel, unscrew 4 screws, lift 4 small buckles, and shake it slightly, you can remove it.

6. After the inner barrel is removed, clean the inner barrel first, pay attention to the inner barrel connected to the internal machine circuit, and the circuit wires are intricate and do not move. Then spray the washing machine detergent, dry it and put it back in as is.