The faucets of the vegetable and wash basins are often blocked, why is this happening? How can it be

It may be that you throw something that is not easy to clean, or it may be that there is too much garbage in the sewer, and the sewer is relatively narrow, which will lead to frequent blockages. When washing vegetables or washing hands, do not throw away some vegetable leaves or toilet paper, and clean the drain frequently.

It may be that the water quality in these two locations is not very good, and you need to find someone to get through, and then you usually need to clean the surrounding area from time to time to prevent blockage.

It may be due to the fact that there are too many houses in the water, and there is no water purifier installed in the house. That's why the faucet will be clogged. When you install a sink all the time, you can filter the water by purchasing a water purifier to install it under the sink.

This will prevent the faucet from clogging.

The solution to this kind of blockage is to take off the faucet and pour HCl into it, because the rust is alkaline, HCL and the rust can be neutralized, so as to eliminate the rust.

In order to completely remove the rust, the HCL should be poured in and left for a slightly longer period of time, in order to allow the HCl to fully react with the rust. After neutralization, the faucet should be rinsed several times with clean water to ensure that it can be rinsed clean. For faucets without a filter, cleaning with vinegar will do.

What kind of faucet is it? What is the leak?

If it is a bent faucet and the root of the pipe is leaking, it is generally an O-ring (gasket) there that is broken, and the water leaks out from there, and when the water remaining in the elbow leaks out, it will not leak. As shown in the red circle in the figure:

In life, when we cook in the kitchen, we often use the faucet to wash vegetables. After a long time, it is easy to leak. 1. Causes of water leakage at the water outlet:

That is due to the wear and tear of the shaft gasket inside the faucet. Use pliers to loosen the gland and remove it, take out the shaft gasket with a clip, and replace it with a new shaft spacer.

2. The reason for water leakage in the lower part of the faucet: it is caused by the wear of the triangular sealing gasket in the gland. You can loosen the screws and remove the tie head, then loosen the gland and remove it, and then take out the triangular seal shop on the inside of the gland and replace it with a new one.

3. Water leakage at the joint of the pipe: Roughly the cap nut is loose, then you can re-tighten the cap nut or replace it with a new U-shaped gasket.

Regardless of the appearance of a push-to-press faucet, whether it has two handles for hot and cold water or only one handle that controls both hot and cold water, it works according to certain basic principles. Here's how to take apart a push-to-tap and fix a dripping problem

Step 1: Turn off the water supply and remove the small screws on or behind the faucet handle to remove the handle that is fixed to the faucet body. Some screws are hidden underneath metal buttons, plastic buttons, or plastic pieces that snap into or screw into the handle.

As soon as you open the button, you will see the handle screws mounted on the top. If necessary, use some penetrating lubricant like WD-40 spec to loosen the screws.

Step 2: Remove the handle and look at the parts of the faucet. Remove the fill nut with large carp pliers or an adjustable wrench, being careful not to leave scratches on the metal. Turn the spool or shaft in the same direction you rotated when you turned on the faucet to unscrew them.

Step 3: Remove the screws that hold the washer in place. If necessary, use penetrating lubricant to loosen the screws. Inspect the screws and spool and replace them with new ones if damaged.

Step 4: Replace the old gasket with a new one that is exactly the same. A new gasket that is almost exactly a match for the old gasket will generally stop the faucet from dripping.

You also want to notice whether the old washer has a bevel or a flat one, and replace it with the same new washer. Gaskets designed for cold water only expand violently when hot water flows through them, clogging the outlet and slowing down the flow of hot water. Some gaskets will work in both hot and cold water, but you want to make sure that the gasket you buy for replacement is exactly the same as the original.

Step 5: Attach the new gasket to the spool and reinstall the parts in the faucet. Rotate the spool in a clockwise direction. Once the spool is in place, reattach the fill nut. Be careful not to leave scratches on the metal with the wrench.

Step 6: Reinstall the handle and put the button or disc back in. Turn the water supply back on and check for any leaks.

How to repair a leaking faucet in a vegetable washing basin, easily repair.