How to install the washing machine inlet pipe, how to install the washing machine inlet pipe

It depends on what type of faucet it is. The different types of faucets are installed as follows:

Washing machine-style faucets:

When installing the water inlet pipe, you don't need to install the steel head, directly install the water inlet pipe on the faucet, press it down directly by hand, that is, a white part of the water inlet pipe port, press it down, the steel ball ring is stuck on the top of the faucet, and finally the water inlet pipe is directly inserted into the faucet, and the water inlet pipe can be easily connected.

Normal faucet:

If you want to buy the adapter of the faucet, install the adapter of the faucet first, then press down the white part of the water inlet pipe, put the water inlet pipe directly on the faucet, and install it tightly.

Faucets with steel heads:

There is no need to buy an adapter, just clamp the faucet with a steel head, and then tighten all the screws around it.

After tightening, screw the other end of the water inlet pipe directly on the washing machine, and after tightening the screws, the water inlet pipe is installed.

Precautions for using the washing machine:

1. When using the washing machine, be sure to clean the washing machine regularly.

2. Use the washing machine according to the relevant instructions, and do not blindly explore the functions of the washing machine to prevent damage to the washing machine system.

Washing machine inlet pipe installation method:

1. To observe the faucet of the washing machine, if the faucet is a washing machine-style faucet, then the installation is very simple.

2. When the washing machine-type faucet is installed on the water inlet pipe, there is no need to install the steel head, we directly install the water inlet pipe on the faucet, and press it down directly by hand, that is, a white part of the water inlet pipe port, after pressing down, the steel ball ring is stuck on the top of the faucet, and finally the water inlet pipe is directly inserted into the faucet, and the water inlet pipe can be easily connected.

3. If it is an ordinary faucet, then it is relatively a little troublesome, we have to buy the adapter nozzle of the faucet, install the adapter nozzle of the faucet first, and then press and hold the white part of the water inlet pipe to press down, and put the water inlet pipe directly on the faucet, and install it tightly.

4. If the faucet has a steel head, then we don't need to buy an adapter, just use the steel head to jam the faucet, and then screw all the screws around and tighten it.

5. After tightening, screw the other end of the water inlet pipe directly on the washing machine, and after tightening the screws, the water inlet pipe will be installed, and the method is really simple.

1. Tools Raw materials: raw rubber, screwdriver.

2. Prepare the water inlet parts of the washing machine, and also prepare a Phillips screwdriver.

3. Put the black rubber ring into it first, then put the white one in, and then screw it in a little by hand or with a screwdriver, it is best to screw the balance point, and don't tighten it too tightly, about half of it.

4. Put the faucet in, put it in the middle position, and then screw it in by hand or with a screwdriver, be careful not to tighten it too tightly, and wait for all four sides to screw it in a little bit, and then open the rolling ridge to start tightening.

5. Wrap more than a dozen or more large Zen infiltration points with raw rubber, and then install the water outlet of the upper water pipe to test whether there is water leakage.

6. Then press the washing machine inlet device and plug it in.

1. Hold the connector in one hand, hold the buckle with the other hand and pull it down, separate the connector from the water inlet pipe, loosen the four fastening screws on the upper connector, and unscrew the connector, so that there is a gap of three threads between the upper and lower connectors, if the faucet is too thick, you can remove the plastic guide bushing inside;

2. Evenly adjust the four screws of the connector, so that the two screws on the wall side are in full contact with the outside of the faucet, and the screws of the wall can be screwed in by hand first, and the upper connector is against the faucet, so that the internal sealing ring is fully in contact with the faucet;

3. Rotate the two screws on the opposite side of the wall to make it contact with the faucet, and then tighten it, rotate the lower connector until the upper and lower connectors are tightened, and the gap between the two should not exceed three millimeters of dust, press the buckle of the water inlet pipe down, and at the same time let the water inlet pipe go up into the lower connecting seat, and then loosen the buckle.

Washing machine inlet pipe installation method:Prepare materials: water inlet pipe, screws, screwdriver.

1. Hold the connecting seat and pull down the buckle to separate the connecting seat and the water inlet pipe.

2. Evenly adjust the 4 screws of the connector so that the 2 screws on the wall side are in close contact with the outside of the faucet.

3. Put the upper connector against the faucet, and then let the sealing ring inside it fully contact the faucet.

4. Rotate the 2 screws on the opposite side to make it contact with the faucet, and then tighten it.

1. Take out the fittings, find the end with the joint, press down the slider, and separate the inlet pipe joint from the inlet pipe. 2. Loosen the four screws on the inlet pipe joint evenly and put it into the faucet, if the faucet is too big, you can remove the bushing. The front is like a limb, and then Huishi loosens the plastic connector nut until about 3-4 turns of threads are exposed.

3. Put the water inlet pipe joint on the faucet, put the black washer in the joint and the faucet tightly, then fix it with a screwdriver, and tighten the plastic interface nut until there is no leakage. 4. Connect the water inlet pipe and the water inlet pipe joint, connect the other end of the water inlet pipe with the water inlet of the washing machine, and tighten the plastic nut.

1. In the actual use of the water inlet pipe of the washing machine, sometimes the water inlet pipe of the washing machine is too short to be used, and the water inlet pipe of the washing machine needs to be lengthened for use.

2. In the above situation, you can buy a water inlet pipe that can be lengthened and spared, and the length of this water inlet pipe is generally meters.

3. There are two ends of the outer screw, one end is the screw sleeve, and the other end is the inner wire screw sleeve, and one end of the outer wire screw is connected and fastened with one end of the water inlet pipe with the random belt during installation, and the other end is screwed into the water inlet valve port of the washing machine. In this way, the length of the water inlet pipe is 3 meters. If you don't need to lengthen it in the future, you can also remove it at will.

1. Take out the water inlet pipe fittings of the automatic washing machine, find the end with the water inlet pipe joint, and then press down the slider to separate the water inlet pipe joint from the water inlet pipe.

2. Loosen the four screws on the inlet pipe joint evenly until the faucet can be inserted, if the faucet is too large, you can remove the bushing.

3. Then loosen the plastic interface nut until about 3-4 turns of threads are exposed.

4. Put the Jinyou jujube base water pipe joint on the faucet, attach the black washer in the joint to the faucet, then tighten the screws with a screwdriver, tighten the plastic Yanhuai mouth nut, tighten it until it does not leak and stop, and then connect the water inlet pipe and the water inlet pipe joint, connect the other end of the water inlet pipe with the water inlet of the automatic washing machine, tighten the plastic nut, and the device is completed.

5. Press down the slider on the inlet pipe head, pierce the water inlet pipe into the water inlet pipe joint, hang the locking rod on the water inlet pipe joint, put down the slider, and hear the "pop" sound to indicate that the device is in place.

6. Put the nut of the water inlet pipe on the joint of the water inlet valve of the washing machine, ensure that it has sufficient cooperation with the water inlet valve port, tighten the nut of the water inlet pipe, and shake it slightly to admit that it is fastened in place.

7. If the inlet pipe needs to be lengthened, a special extension pipe must be used and properly connected.