What happens to angle grinders burning saw blades, what saw blades are used for angle grinders sawin

The quality of the blade is not good, or the blade is not suitable for the material you want to cut.

However, depending on the frequency of the broken saw blade, the general point of continuous cutting for 15min almost has to be replaced.

Woodworking saw bladesThe angle grinder is designed to be inherently unfavorable for control when cutting, and the angle between the handle and the grinding wheel is not like that of a special hand chainsaw and gimbal machine, which can directly resist the direction of the reaction force with your hand. But the handle of the angle grinder is on the side of the grinding wheel. So once the rotating saw blade or grinding wheel is suddenly blocked, the force ** becomes difficult to control.

Precautions for angle grinders.

When starting the grinding wheel, it must be 40 to 60 seconds after the speed is stable before grinding, and the grinding tool should stand on the side of the grinding wheel, not facing the grinding wheel, in order to prevent the grinding wheel from breaking and flying out and hurting people.

On the same grinding wheel, it is forbidden for two people to use at the same time, and it is not allowed to grind on the side of the grinding wheel, when grinding, the operator should stand on the side of the angle grinder angle grinder, do not stand on the front of the grinder, in order to prevent the grinding wheel from cracking, accidents, and at the same time it is not allowed to wear gloves to operate, and it is strictly forbidden to operate in the pile and laugh and play during grinding.

The angle grinder blade sizes are classified as follows:

1.Ultra-thin angle grinder cutting disc series.

Angle grinder cutting disc sizes * and 180*.

2.Stainless steel angle grinder cutting disc special series.

Angle grinder cutting disc sizes * and 400 *.

3.Cast iron angle grinder cutting burn cutting disc series.

Angle grinder cutting disc sizes * and 180*.

4.Pneumatic tool Dan spike angle grinder cutting disc series.

Angle grinder cutting disc sizes * and 180*.

Introduction of angle grinders:

Angle grinder, also known as grinder or disc grinder, is an abrasive tool used for FRP cutting and grinding. Angle grinder is a portable power tool that uses FRP to cut and grind, mainly used for cutting, grinding and brushing metal and stone.

The common models of angle grinders are divided into 100 mm (4 inch mm) (5 inch mm (6 inch mm (7 inches) and 230 mm (9 inches) according to the accessories used, and the small size angle grinders used in Europe and America are 115 mm. <>

1. The saw blade of the angle grinder cannot be removed and heated with fire, and then cooled, it is OK, and you can try it by using the principle of thermal expansion and cold contraction. 2. Grinding, cutting, rust removal and polishing of metal components by using high-speed rotating thin slice grinding wheels, rubber grinding wheels, steel wire wheels, etc. Angle grinders are suitable for cutting, grinding and brushing metal and stone, and do not use water during operation.

3. A guide plate must be used when cutting stone. For models equipped with electronic controls, grinding and polishing can also be carried out if suitable accessories are installed on these machines.

Summary. Hello, the solution to the angle grinder motor does not burn but the saw blade does not rotate: The possible reasons why the motor does not run after the power connection are:

1. If the power supply is broken, just repair the power supply. 2. The joints of the angle grinder are loose, and check whether all the joints are correct. 3. The switch has poor contact and needs to be repaired or replaced.

4. The brush is not in contact with the surface of the commutator, and the carbon brush can be replaced. 5. The switch contact is burned out and the switch needs to be repaired or replaced. 6. The mechanical parts are stuck, and the mechanical parts are checked and reassembled.

The angle grinder motor does not burn, but the saw blade does not rotate.

Hello, the solution to the angle grinder motor is not burning but the saw blade does not rotate: the possible reasons why the motor does not run after the power is connected are: 1. The power supply is broken, and the power supply can be repaired.

2. The joints of the angle grinder are loose, and check whether all the joints are correct. 3. The switch has poor contact and needs to be repaired or replaced. 4. The brush is not in contact with the surface of the commutator, and the carbon brush can be replaced.

5. The switch contact is burned out and the switch needs to be repaired or replaced. 6. The mechanical parts are stuck, and the mechanical parts are checked and reassembled.

Hello, the solution to the angle grinder motor is not burning but the saw blade does not rotate: the possible reasons why the motor does not run after the power is connected are: 1. The power supply is broken, and the power supply can be repaired.

2. The joints of the angle grinder are loose, and check whether all the joints are correct. 3. The switch has poor contact and needs to be repaired or replaced. 4. The brush is not in contact with the surface of the commutator, and the carbon brush can be replaced.

5. The switch contact is burned out and the switch needs to be repaired or replaced. 6. The mechanical parts are stuck, and the mechanical parts are checked and reassembled. The surface of the commutator is not smooth; Remove debris and make the surface of the commutator smooth and clean.

Hello, the solution to the angle grinder motor is not burning but the saw blade does not rotate: the possible reasons why the motor does not run after the power is connected are: 1. The power supply is broken, and the power supply can be repaired.

2. The joints of the angle grinder are loose, and check whether all the joints are correct. 3. The switch has poor contact and needs to be repaired or replaced. 4. The brush is not in contact with the surface of the commutator, and the carbon brush can be replaced.

5. The switch contact is burned out and the switch needs to be repaired or replaced. 6. The mechanical parts are stuck, and the mechanical parts are checked and reassembled. The surface of the commutator is not smooth; Remove debris and make the surface of the commutator smooth and clean.

Summary. Stop using the machine, enter a safe area, inspect and remove impurities or faults inside or outside the machine that could cause the phenomenon.

Stop using the machine, enter a safe area, inspect and remove impurities or faults inside or outside the machine that could cause the phenomenon.

Can you elaborate on that a little bit more?

If the angle grinder cuts the finch and breaks the fire, emergency measures need to be taken immediately. First, immediately turn off the power and extinguish the fire with a fire extinguisher. If you can't find a fire extinguisher, cover the fire with a wet towel, sand, or other things to stop the air from burning further.

After waiting for the ignition area to cool down, check the machine for any damage, and if necessary, repair or replace the corresponding parts. In addition, when using angle grinders, we must pay attention to safety, purchase quality-assured accessories, strengthen maintenance, and comply with relevant safety regulations to avoid similar accidents.

What's going on with angle grinder burning? Hello dear, the angle grinder line may be burned by the rotor and stator inside the motor, resulting in sparks and smoke, or the carbon brush spring is worn out for a long time to produce sparks, and the accompanying objects are smoking, and there may be other internal electronic messes and noisy parts are heated and smoked, and the angle grinder is turned on **Smoke should be a short circuit of the motor**, you must find a professional electrical maintenance worker to repair, and it is very dangerous to use it anymore. If you find that the temperature is too high or the phenomenon of smoke when using electrical appliances, you should immediately cut off the power supply and ask a professional electrical maintenance attendant to check.