Electric roller shutter door installation method, electric roller shutter door installation method

That's right. And now** there is.

Gear motors.

When installing.

Super good horizontal line.

Only. Okay, there's one.

The limiter has to be adjusted (that is, the rising and descending positions), there is nothing difficult, and there is a detailed operation manual.

You'll install a manual roller shutter and install an electric one, no problem.

You can make ordinary roller shutter doors, and it is very simple to make electric roller shutter doors.

What gear you are talking about, you may be talking about adjusting the upper and lower limits, that is, to determine the highest position that the rolling door usually opens to and the lowest position that it descends to, which is determined by adjusting the limiter on the rolling door machine.

The principle of adjusting the limiter is that after installing the roller shutter, first loosen the fastening screws on the limiter, press the rising key on the button box of the roller shutter machine, open the roller shutter door to the highest position (upper limit), press the stop button to stop the roller shutter door, and then dial the slider on the limiter to make it press down the upper limit micro switch on the limiter, and then tighten the fastening screws, so that every time the roller shutter door runs to this position, it will stop, which is the highest position when the roller shutter door is usually opened.

In the same way, you can adjust the lower limit (the position where the roller shutter door is usually closed).

For electric roller shutter doors, active liners, passive liners, shaft cores, etc. should be welded in the drum before installation. But all are relatively simple, as long as you can install a normal roller shutter door, there will be no problem installing an electric roller shutter door. Besides, the rolling door machine has installation instructions.

Introduction: Electric roller shutter door motor is a lot of automated home decoration like the decoration method, in modern home generally like to use, the following by me for you to bring the installation method of electric roller shutter door, let's go and see it!

The door body is made of high-strength galvanized steel sheet, which is durable and beautiful in appearance. The door panel is made of 20 cm or 80 cm main assembly, and the appearance is treated with a unique anti-rust chemical coating layer of multi-layer baking paint, which is not easy to get dirt and never rust. Luster:

Bright color and anti-corrosion; Make the door have a good balance state in any position, the door body guide rail both sides and the curtain are equipped with silent wool strips, and the unique silent system that the silencing guide groove has makes the door body have a good balance system in any position and open without fault and no noise, greatly increases the service life of the door body.

Clause. First, draw a line at the position of the door frame that needs to be installed. Indicate the size, and then find the staff to design a suitable electric roller shutter door, here it is worth noting that the height of the frame is a little higher than the height of the door leaf.

Clause. Second, first fix the door frame of the electric roller shutter door, and remove the fixed plate at the bottom of the door frame first. (Note:.)

The ground on both sides of the hole should be reserved for grooves, and after being corrected, the wooden wedge should be fixed, and the iron feet of the door frame should be welded firmly with the embedded iron plates. It can be firmly plugged with cement mortar or fine stone concrete with a strength of not less than 10MPa. )

Clause. 3. Install the main body of the electric roller shutter door. It is necessary to ensure that the electric roller shutter door and the wall form a whole, and the closure should be done well, and then the hole and wall should be painted.

After painting, the door gap should be evenly flat, and the electric roller shutter door should be free and light, and should not be too tight, too loose and not too tight.

Electric roller shutter doorsWhat is it, then we are not common electric rolling doors in life, some large shopping malls, some small doors will be used, and there is the parking garage in our community, which are electric rolling doors. Then do you know how to repair it if it is broken, how to install it, we will give you an understanding of how to repair the electric rolling shutter door if it fails, and how to install the electric rolling shutter door.

1. What should I do if the electric roller shutter door fails?

1. The motor of the electric roller shutter door and the drum mandrel are connected by a transmission chain, and the motor foot is fixed on the sprocket bracket plate with screws. Before replacing the motor, the roller shutter must be lowered to the low end or supported by a bracket. This is due to the fact that the braking of the rolling shutter door is to rely on the brake on the body of the electric finch belt machine to work, and after the motor is removed, the rolling shutter door is not braked and actively slides down; Second, the transmission chain can be relaxed, and it is convenient to remove the chain.

2. The process of replacing the motor: the motor wiring is symbolized and then removed, the motor anchor screws are loosened and the transmission chain is removed, and the motor anchor screws are finally removed and the motor is removed; The order of the new motor device is reversed, but it should be noted that after the motor is installed, the annular hand chain on the main body should be naturally straight down, and there should be no jamming.

3. The location and factors of the occurrence of control failure: . .The relay (contactor) contact is sticky, the stroke micro switch fails or the contact is deformed, the slider set screw is loose, and the backing plate screw is loose to displace the backing plate, so that the slider or nut can not move with the rotation of the screw rod, the limiter transmission gear is damaged, and the upper and lower keys of the button are stuck.

Second, the installation of electric rolling shutter doors.

1. Draw a line in the direction of the door frame of the demand device, indicate the size of the scale, and then find the staff to design a suitable electric roller shutter door (it is worth noting here that the height of the frame is a little higher than the height of the door leaf).

2. Fix the door frame of the electric roller shutter door, and first remove the fixed plate at the lower part of the door frame (note: grooves should be reserved on the ground on both sides of the hole, and after proofreading, the wooden wedge should be fixed, and the iron feet of the door frame should be welded firmly with the embedded iron plates.

3. The main body of the electric roller shutter door leaf is installed. Be sure to make sure that the electric roller shutter door and the wall are combined, and the closure should be done well, and then the hole and wall should be painted. After the painting is finished, the door gap should be uniform and flat, and the open electric roller shutter door should be free and simple, and should not be too tight, too loose and ** scene.

The above article is to introduce to you how to repair the electric roller shutter door and how to install the electric roller shutter door. I believe that everyone can also understand some knowledge after reading it. I hope it will be helpful to everyone.

If there is a fault repair, you must pay attention to safety, repair it yourself, and you must find the property personnel.

1. Draw a line at the position of the installation door frame, measure the size, and customize the electric roller shutter door that meets the specifications. 2. Fix the door frame of the electric roller shutter door, and remove the fixing plate at the lower part of the door frame first. 3. Install the main body of the electric roller shutter door.

4. The operator fixes the motor on the main board, and then uses the chain to connect the wheel disc with the motor base, connects the remote control wire box device with the motor, and tests whether the handle of the roller shutter door is reversed. 5. Weld the electric roller shutter door firmly. 6. Pull the switch of the electric roller shutter door to carry out the lifting demonstration operation to ensure that it will not fail and other conditions, thus causing safety accidents.

Maintenance knowledge of electric roller shutter doors.

1. During the use of the electric roller shutter door, try to keep the controller and voltage stable, prohibit installation in a very humid environment, and do not open the remote control at will. Pay attention to whether the passage is blocked, hinder the door from descending, and stop the motor operation immediately if there is an abnormal response.

2. To frequently check the switch of the upper and lower stroke of the electric rolling shutter door, add lubricating oil to the stroke controller to maintain normal and good operation, in addition, the operator manually controls the rolling shutter door, checks the operation of the device, and corrects the position of the upper and lower travel switches, so that the electric rolling shutter door is in the appropriate position when it is opened or closed, and the inspection process strictly prevents the electric rolling shutter door from rushing to the top or bottom or reversing, if there is an emergency, it should immediately stop rotating and cut off the power supply.

3. It is best for the operator to check the manual switch and manual lifting decoration of the electric roller shutter door frequently to prevent the electric roller shutter door from failing or causing unnecessary safety accidents in an emergency.

4. To keep the track running smoothly, clean the track of the electric shutter door in time, keep the interior clean, the shutter door motor and transmission chain should be filled with lubricant frequently, check the devices and switch control box in the control box, fasten the wiring port, fasten the screws, etc., clean the dust and dirt in the control box, on the surface and on the button, and prevent the button from getting stuck.

1.Measure the size of each part of the roller shutter door according to the size and model of your own door, check whether the opening of the door is consistent with the size of the roller shutter door, and whether the embedded position and quantity of the guide rail and bracket are correct. Also measure the elevation of the hole, eject the vertical line of the two rails and the center line of the reel.

2.The horn is welded on the embedded iron plate, and the drum bracket is fixed with screws to install the drum, and the installation of the drum should rotate flexibly.

3.Install the reducer dust family, transmission system and electric tie street system.

4.Install the pre-installed curtain plate on the drum, and then install the guide rail, which needs to be installed in the position specified in the drawing. The guide rails on both sides and above are welded to the embedded parts of the wall and welded into a whole. The trapped rails of each guide should be on the same vertical plane.

5.Finally, the water curtain sprinkler system is installed and connected with the master control system. After the installation is completed, the test run is carried out, and the door is opened and closed by the motor several times, and then adjusted to a state of no jamming and no abnormality.

How is an electric roller shutter door installed? Tools Raw material roller shutter doors. Motor.

Method Step 1, the first step, what we want to do is that the accessories are classified into reels, reels, reels, and reels, which are driven by electric shock to drive the reel to rotate. 2. In the second step, we first prepare, all the materials, measure the size, see how much is long, how high, how wide, this step must not be wrong. 3. The third step is to start installing the accessories and the cord, tie the reel with a rope to the cord, install it on the boards on both sides, and then start to install the motor and put it in the square slot.