How to install the fast rolling shutter door, the installation method of the rolling shutter door

Quick Roller Shutter Door Installation Steps:

1.Hole size review: Before installation, it is necessary to check whether the hole is consistent with the size of the product. The number and location of embedded parts should also be re-checked. And measure the standard height of the opening, determine the vertical of the two guide rails and the center line of the reel.

2.Fixing device position: The backing plate is welded on the embedded iron plate, and after the left and right brackets are fixed, the reel can be installed. Finally, the reducer and transmission system as well as the electrical control system are installed.

3.Installing the curtain and rails: The curtain is spliced together and then installed on the reel. Then, according to the drawing, weld the guide rails on both sides and above the wall embedded parts at the specified position, and weld them into a whole, noting that each guide rail should be in the same vertical plane.

4.Debugging: Turn on the power supply, check whether the motor and reducer are running normally, whether the direction of rotation of the drum is correct, and whether the rotation is flexible.

Then carry out the opening and closing movement to confirm that the speed of opening and closing, such as flexibility, no lag, no noise, etc., meets the requirements. After all the commissioning is completed, the protective cover is installed.

5.Clean up the site: clean up the dirt and garbage on the site.

The installation steps of the rolling shutter door should start from the door frame, then install the door head, install the scroll behind the door head, and finally fix the shutter door of the rolling shutter door on the scroll, and the specific operation steps are as follows:

1. Use expansion bolts to fix the door frames on both sides of the roller shutter door.

2. Pick up the head of the roller shutter door.

3. Two people cooperate, and also use expansion bolts to fix the door head.

4. Two people fix the scroll on the internal bracket of the door head at the same time.

5. Hang the louver slowly on the scroll.

6. The installation of the roller shutter door is completed after it is fixed.

You can make ordinary roller shutter doors, and it is very simple to make electric roller shutter doors.

What gear you are talking about, you may be talking about adjusting the upper and lower limits, that is, to determine the highest position that the rolling door usually opens to and the lowest position that it descends to, which is determined by adjusting the limiter on the rolling door machine.

The principle of adjusting the limiter is that after installing the roller shutter, first loosen the fastening screws on the limiter, press the rising key on the button box of the roller shutter machine, open the roller shutter door to the highest position (upper limit), press the stop button to stop the roller shutter door, and then dial the slider on the limiter to make it press down the upper limit micro switch on the limiter, and then tighten the fastening screws, so that every time the roller shutter door runs to this position, it will stop, which is the highest position when the roller shutter door is usually opened.

In the same way, you can adjust the lower limit (the position where the roller shutter door is usually closed).

For electric roller shutter doors, active liners, passive liners, shaft cores, etc. should be welded in the drum before installation. But all are relatively simple, as long as you can install a normal roller shutter door, there will be no problem installing an electric roller shutter door. Besides, the rolling door machine has installation instructions.

The installation steps of the rolling shutter door should start from the door frame, then install the door head, install the scroll behind the door head, and finally fix the shutter door of the rolling shutter door on the scroll, and the specific operation steps are as follows:

1. Use expansion bolts to fix the door frames on both sides of the roller shutter door.

2. Pick up the head of the roller shutter door.

3. Two people cooperate, and also use expansion bolts to fix the door head.

4. Two people fix the scroll on the internal bracket of the door head at the same time.

5. Hang the louver slowly on the scroll.

6. The installation of the roller shutter door is completed after it is fixed.

1. The upper part of the opening of the roller shutter Bicha hidden door shall not be equipped with ventilation pipes, water pipes, etc.;

2. The power supply line (three-phase five-wire and fire control signal line) is laid by the user to the side of the electrical control box next to the rolling door machine;

3. After the door of the roller shutter is installed, install the ceiling, and the edge of the ceiling should be 50mm away from the curtain plate to avoid friction;

4. When debugging and using, it is strictly forbidden to stand at the bottom. Electrical facilities shall not be dismantled without authorization;

5. According to the fire management regulations, the fire shutter door is a special facility for fire protection, and shall not be used for other purposes, and no items shall be stacked directly below the shutter;

6. After installation and commissioning, start once a quarter to check the electrical and mechanical properties, and pay attention to the safety of operation during inspection.

7. During the routine fire safety inspection of Qingcheng every quarter, the chain lubricating oil of the starter motor must not be missed, which is also an important part of the omission of many property units or fire units during the inspection.