How to install 10 meter lithium battery solar high pole street light

The following steps are required to install a 10m lithium battery solar high pole street light:

1.Determine where to install: Choose a well-lit, unobstructed location to ensure that the solar panels receive the sunlight adequately.

2.Prepare installation materials: In addition to the solar high-pole street lights themselves, you also need to prepare the materials required for installation, such as screws, expansion bolts, cables, etc.

3.Install the solar panels: Fix the solar panels on a high pole to make sure they are facing due south and the inclination is equal to the local latitude for the best solar energy harvesting.

4.Install the light pole: Fix the light pole to the ground and use expansion bolts to secure it to the ground.

5.Connect the cable: Connect the solar panel with the controller on the light pole to ensure that the cable connection is firm and reliable.

6.Install the lamp head: Fix the light head on the light pole to make sure it is firm and stable.

7.Debugging the system: Connect the power supply, make sure the solar panel can be charged normally, and control the switch of the lamp head through the controller.

8.Test the lighting effect: At night or in the case of blocking the sun, test the lighting effect of the solar high pole street light to ensure that it can work properly.

9.Regular maintenance: Regularly check the cleanliness of the solar panels, remove dust and debris to ensure that they are working properly.

To sum up, installing a 10m lithium battery solar high pole street light requires choosing a suitable installation location, fixing the solar panel and light pole, connecting the cables, debugging the system and testing the lighting effect. Regular maintenance is also an important step to ensure that the solar high pole street lights are working properly.

The installation of the same as the ordinary solar street lamp, the installation of the solar street lamp is particularly convenient, and the battery box has two lines, one line is connected to the solar panel, and the other line is connected to the light source.

When the battery is placed in the control box, it must be handled with care to prevent smashing the control box;

The connecting wires between the batteries must be bolted against the binding posts of the batteries and copper gaskets must be used to enhance the conductivity;

After the output line is connected to the battery, it is forbidden to short-circuit under any circumstances to avoid damaging the battery;

When the output line of the battery is connected to the controller in the pole, it must pass through the PVC threading pipe;

After the above is completed, check the wiring on the controller side to prevent short circuits. Close the door of the control box after normal.

Put the battery into the battery box, and connect the connecting wire to the controller according to the technical requirements;

First connect the battery, then the load, and then the solar panel;

When wiring operation, it must be noted that the wiring and the terminal marked on the controller cannot be connected wrong, and the positive and negative polarities cannot collide or be reversed;

Huangchuan Limin Technology Solar Street Light Factory has successfully installed tens of thousands of solar street lights.

Nowadays, the latest solar street lights do not require buried batteries.

It's all lithium batteries.

Zaozhuang Jixing Optoelectronics.

Hello! Glad for your question! How to install solar lithium battery street lights:

Tools Raw materials: light poles, solar panels, storage and control integrated lithium batteries, LED lamp heads, picker arms, solar panel brackets, ground cages, screws, gaskets, wires, etc., wrenches, screwdrivers, vises, tapes, etc. 1. Embedded parts (ground cage stuffy blind) pouring. 2. Take the 6-meter street lamp pole as an example, the size of the embedded pit is approximately

60*60cm, 70cm in depth. Wrap the position of the screw rod with a rubber strip and then bury it for pouring. 3. After connecting the wire, the lamp head passes through the pick arm, and the hole corresponding to the lamp pole is pierced to the top, and then the corresponding screw is fixed.

4. The lithium battery with integrated storage and control is installed on the bracket behind the solar panel, corresponding to the reserved four screw holes. 5. The solar panel is installed in the hole position reserved for the solar panel bracket and fixed with screws. 6. After the solar panel and the integrated lithium battery are installed on the bracket, they are installed on the top of the street lamp pole for fixation.

7. The integrated lithium battery for storage and control is divided into a black cap (connected to a solar panel) and a white cap (connected to an LED lamphead). 8. Schematic diagram of the wiring of the solar street lamp.

Fabricate a metal hoop yourself so that it can be securely attached to the pole, and then screw the solar lamp to the hoop.

Zaozhuang Jixing Optoelectronics is a production and sales entity integrating the manufacturing, sales, installation and maintenance of street lamps. At present, the company's products mainly include solar street lamp series, LED street lamp, garden lamp, landscape lamp and so on.

At present, the company's solar street lights mainly use lithium batteries, and the main reasons are:

1. The use effect of lead-acid batteries is much inferior to that of lithium batteries. In terms of battery capacity and stability, lithium batteries have a stable advantage.

2. The main reason is that the pollution of lead-acid batteries is very serious, and the state has banned the use of such batteries.

3. The lithium battery should be small in size, easy to install, carry, stable in performance, and will not suffer severe impact and accidents like other batteries. Now the lithium battery can be placed on the back of the street lamp head or the back of the battery board, which is very convenient.

Since January 2015, all the solar lamp series products produced by Zaozhuang Jixing Optoelectronics have used lithium batteries, which are better than lead-acid batteries in terms of quality, and have not violated national regulations. Environmental protection, energy saving, high efficiency, no adverse hazards.

。。。Ad? I found them all and asked.

1. Check and determine whether the model of the light pole at the installed position is correct (such as single head, double head), and cooperate with the corresponding long and short pick arms; Cut the appropriate wire to the corresponding position, and generally reserve 150mm at each end of the stripping wire.

2. Install the jump arm and lamp head, determine the position and levelness of the lamp, and take the lamp pole as the benchmark.

3. Check whether the lamp wire is tightly fastened after wiring.

4. Connect the light source and threading, connect the wire correctly according to the manual, and pay attention to the positive and negative poles.

5. Check whether the connection is firm after connecting the wire. During the installation of the light source, pay attention to the projection surface of the light source perpendicular to the ground, not the mounted boom surface.

6. After connecting the light source, first use a multimeter to test its resistance value and whether there is grounding with the rod body, and then use the battery to test it to confirm the correct connection.

Solar street lights are mainly composed of solar panel components, intelligent controllers, battery packs, light sources, light poles and brackets. Solar street lights use solar panels to convert solar radiation into electricity during the day, and then store the electrical energy in the battery through the intelligent controller. When night comes, the sunlight intensity gradually decreases, and when the intelligent controller detects that the illuminance decreases to a certain value, it controls the battery to provide power to the light source load, so that the light source will automatically turn on when it is dark.

The intelligent controller protects the charging and over-discharging of the battery, and controls the opening of the light source and the lighting time. Establish the installation location of the street lamp: The members of the photovoltaic construction team will determine the installation location of the street lamp based on the construction drawings and the geological situation of the survey site, and determine the installation position of the street lamp with the street lamp spacing of 40 meters as the benchmark value in the place where there is no shade at the top of the street lamp, otherwise the installation position of the street lamp should be appropriately replaced.

Excavation of street lamp foundation pit: Excavation of street lamp foundation pit at the set street lamp installation position, if the surface of 1 meter of soft soil, then the depth of our excavation will be deepened.

and identify and protect other facilities at the excavation site. A battery box is built in the excavated foundation pit to bury the battery. If the pit is not wide enough, we will continue to dig wide enough to have enough space for the battery box.

Pouring the embedded parts of the street lamp foundation: In the excavated 1-meter-deep pit, place the pre-welded embedded parts of Kaichuang Optoelectronics into the pit, and put one end of the wire pipe in the middle of the embedded parts, and the other end to the buried battery. And keep the embedded parts, the foundation and the ground on the same level.

Then the embedded parts are poured and fixed with C20 concrete. During the pouring process, it is constantly stirred and symmetrical to ensure the compactness and firmness of the whole embedded parts. After the construction is completed, the residue on the positioning board should be cleaned up in time, and the installation of solar street lights can only be carried out after the concrete is completely solidified.

Solar street lampSolar street lamp is powered by crystalline silicon solar cells, maintenance-free valve-regulated sealed battery to store electric energy, LED lamps as a light source, and controlled by an intelligent charge and discharge controller, which is an energy-saving street lamp instead of traditional public electric lighting. Solar street lights do not need to lay cables, do not need AC power supply, and do not incur electricity bills; Solar street lights save worry and trouble, which can save a lot of manpower and energy. Solar street lamps adopt DC power supply and light-sensitive control; It has the advantages of good stability, long life, high luminous efficiency, easy installation and maintenance, high safety performance, energy saving and environmental protection, economy and practicality.

It can be widely used in the city's main and secondary roads, residential areas, factories, tourist attractions, parking lots and other places. Steel light pole and bracket, surface spray treatment, battery panel connection using patented anti-theft screws. When installing solar street lights, there is no need to install complex circuits, just make a cement base and a battery pit, and fix them with galvanized bolts.