How to wrap the radiator and how to use the radiator

The packaging of the radiator is as follows:

1. Choose a radiator style with a beautiful appearance.

In other words, if the radiator itself becomes an ornament, why decorate it twice? As far as the mainstream steel radiators and copper-aluminum composite radiators in the current market are concerned, there are usually many styles given by merchants, and they have different colors and heights. In special cases, users can customize according to their own needs.

In addition to this, there is the sale of art radiators and so on.

2. Use wooden horizontal shutters.

As a shield for radiators.

The improved wooden horizontal shutters can freely adjust the air output of the radiator like the shutters, and the construction is also very simple and not complicated.

3. Make the heating hood into a movable type.

Because the movable heating hood is easy to move, can be used for maintenance work, and the width is narrower than that of the fixed heating hood, it takes up less space, so it is more suitable to be used only when the heating hood is wrapped separately on the wall and not other conjoined furniture. According to the length, width and height of the radiator, according to the length of the radiator, the height of the size of more than 100 mm, the height of more than 50 mm, the width of more than 15 mm, pre-make the frame with side plates and heat dissipation net on three sides, and install the frame directly on the heat sink.

on it.

If the radiator is packed, it also costs a lot of money, and it also takes up space, and now the house is so expensive, if you wrap it, you have to pack it out for one or two flats, it is not worth it, and it also affects the heat dissipation. You can just buy a new type of heater to hang on the wall, leak it on the outside and dissipate heat, how good.

It's best not to wrap it, it affects the heat dissipation, it really needs to be wrapped, and the heat dissipation holes should be left on the opposite side and above the radiator.

What how to pack? Is it to wrap the radiator? Or are you going to buy and sell radiators?

Here's how to use the radiator:

1. When using radiators, it is necessary to deflate first. Tighten the inlet and return valves of the heater and open the air valve.

2. Wait for a period of time, and then open the water inlet valve to let the water flow into the heating pipe. When the exhaust valve can flow out of the water smoothly, it means that the exhaust is complete, and the drain valve is closed.

3. After the exhaust is completed, touch the radiator, and the temperature will rise slowly, indicating that the radiator is working normally. If there is a problem, you need to contact a professional for repair in time.

What should I pay attention to when using household radiators?

1. The installation of the radiator is carried out by a professional designer. When choosing the installation location, it is usually based on the overall situation of the room, and the best location is selected. Therefore, in the process of later use, individuals should not move pipes or radiators without authorization, otherwise it is very easy to seepage.

2. In the process of using the radiator, it cannot be covered with a cloth, although it can prevent dust from dripping, but the heat dissipation effect will also be affected. In addition, the periphery of the radiator is not allowed to place large items, and it is not possible to place a home without feet, which is not conducive to indoor heat dissipation.

3. The load-bearing capacity of the radiator is limited, try not to put the items on the radiator, especially the weight is relatively large, otherwise it is very easy to cause distortion and deformation inside the pipeline, resulting in water leakage.

4. The hot water in the heating pipe cannot be taken out for use. Once taken out, it will cause insufficient temperature in the pipe, reducing the heating effect. Moreover, chemicals will be added to the hot water in the pipeline to prevent corrosion inside the pipeline, which is very harmful to the human body.

Radiators are an essential amenity in a winter home that can provide us with warmth and comfort. However, how to use radiators correctly is a problem that many people are not very clear. Below, I will introduce you to the correct use of radiators.

First of all, before turning on the radiator, we need to make sure that there is no water leakage in the heating line and radiator. If there is a water leak, it needs to be repaired in time. Then, we can open the indoor heating valve and the outdoor heating main valve, and adjust the temperature and air volume of the radiator.

When adjusting the temperature, we need to adjust it according to the actual temperature in the room to avoid the temperature being too high or too low.

Secondly, we need to pay attention to the cleaning and maintenance of radiators. After prolonged use, dust and dirt accumulate inside the radiator, which can affect the efficiency and longevity of the heating. Therefore, we need to clean the radiator regularly, you can use a soft brush to clean the dust and dirt on the surface of the radiator, or you can use a professional cleaner to clean the inside of the radiator.

Finally, we need to pay attention to the safety of radiators. When using radiators, we need to take care to prevent children and pets from touching the radiators to avoid burns. At the same time, we also need to pay attention to prevent the radiator from overheating and avoid disasters.

In short, the correct use of radiators can provide us with warmth and comfort, but we also need to pay attention to the cleaning and maintenance of radiators, as well as safety issues. I hope you can master the correct way to use radiators to make winter warmer and more comfortable.

Find the radiator valve and turn it on by rotating or turning it in the direction marked with the letter o (or ).

In general, there are two kinds of opening and closing valves for radiators, one is the upper and lower knob type switch, and the other is the flip type switch.

The knob-style switch allows for better control of the size of the heater, which is generally clockwise to turn on and make the heat larger, and counterclockwise to turn off or make the heat smaller.

At the same time, it can also be judged according to the symbol on the switch, such as o is the abbreviation of English open, that is, it represents the direction of opening, and S is the abbreviation of English shut, which represents the direction of closing. There is also + - which means to open and get bigger, - is to close and get smaller.

The opening method of the flip-button switch is even simpler, this method is mainly used in old-fashioned radiators, and the wrench is simply gently pressed against the desired position according to the S o or + - mark.

Radiator temperature is uneven:

1. Gas enters the pipeline.

If the temperature of the radiator is uneven to the touch, it is likely that the exhaust pipe enters the air, which will affect the heat dissipation effect of the radiator. We only need to slowly unscrew the exhaust valve bolt (not all at once) to vent, and wait for the water to flow out to prove that the air is released, and then tighten the exhaust valve.

2. There is a shield on the radiator.

For example, the living room and other areas are very hot, but the bedroom area does not feel the heat, it is likely to be caused by too many obstructions or sundries near the radiator, such as some families directly place clothes on the radiator and so on. We can try to remove the obscurations near the radiators to make the heat dissipation smoother, thereby increasing the room temperature.

3. Water leakage. Since the heating uses a water-air circulation system, if the pipe leaks, the heating system will be damaged, and the heat will be dispersed, resulting in the temperature cannot be raised. If there is a water leakage, you should contact the maintenance personnel of a professional heating company as soon as possible for maintenance.

Families heated by steel radiators should pay attention to the correct use, first of all, the valve on the heating pipe can not be opened and closed at will. When the heating system is first run, it generally needs to be commissioned. Each household should adjust the valve of each riser to the appropriate position in time, open the manual release valve of each steel radiator, and discharge the air collected in the steel radiator until each steel radiator is warmed up, and the commissioning is completed.

Once the commissioning is complete, the valve should be fixed and cannot be opened and closed at will.

The steel radiator will be hot when the water is discharged, and it will be cold after a while, and the reason should be the air blockage. That is to say, there is an air column at the high level of the radiator pipe, which leads to the balance of the water supply and return pressure, the water does not flow, there is a pressure relief point when the water is released, and the hot water in the main water flow main pipeline pushes out the cold water in the radiator There is hot water. The solution is to find a radiator worker to open the high slipknot and release the air column in the pipe to make the water in the steel radiator pipe saturated.

If the pipe is installed for a long time, there may also be a semi-blockage, that is, the radiator close to the water supply has a temperature, and the closer to the return water is the cooler the radiator.

Secondly, try to maintain a certain amount of heat dissipation space in the room near the steel radiator. Do not pile up debris on or in front of the steel radiator, otherwise it will affect the heat dissipation effect of the steel radiator. At the same time, the steel radiator cannot be arbitrarily changed.

The installation of steel radiators is organized in a position conducive to indoor heating, which can ensure that the air convection and indoor temperature are relatively evenly balanced, and once the orientation is changed, an imbalance in indoor temperature will be formed. On the other hand, once the pipes and steel radiators are moved, they are very prone to leakage, causing unnecessary losses to the home. Water cannot be released from the steel radiator body at will.

Proper use of radiators.

1. Do not change the heating pipeline at will.

Before installing the radiator, Taizhou Ganghua will send professional staff to measure and observe the room to determine the suitable indoor installation location, so as to achieve a good heating effect. Try to ensure that the heating effect is optimized without affecting the overall home aesthetics. Once the location is changed, it will not only lead to indoor temperature imbalance and affect the effect of home decoration, but also cause local gas blockage and cannot be discharged due to private transformation, affecting the use of the entire gas system in your home.

2. Carefully add a cover to the radiator.

After heating and adding a decorative cover, the heating effect will be affected in the first place. And the technicians experimented that the room temperature difference between the room with the radiator closed and the room temperature was 3-5 compared with the room that was not closed. Moreover, once the radiator is covered, if there is any failure of the radiator, it will affect the timely treatment.

3. Keep the room ventilated.

Many people close the doors and windows after installing radiators in their homes, so that there is not enough oxygen in the room for a long time. Therefore, we must pay attention to occasional ventilation to ensure a clean air environment.

The use of radiators is very simple, as long as the hot water in the radiator is not put indiscriminately when heating, and the heating is as full of water as possible after maintenance, so that it is OK, the humidity of the radiator in the bathroom may be relatively large, if there is water, try to wipe it, which is conducive to maintaining the paint surface, Rubens heating hopes to help you.

If you have a radiator installed at home, you need to know how to use it. How do you use radiators?PChouse will take you to find out.

1. First of all, check the status of the main valve of the heating pipeline at home, if there is only one pipeline, the main valve should be turned off, and like some old residential inlet and outlet valves, there is a general valve, but there are two inlet and outlet valves, then the inlet valve and the outlet valve should be closed at the same time.

2. After closing all the valves, wrap the screws with cloth or twist and rotate the gas release valve of the radiator with pliers to drain the gas in the pipeline. In this way, the water in the radiator is kept at the bottom of the radiator.

3. Next, the water inlet valve should be opened, the return valve is still closed, the water will slowly fill the radiator, at this time, it is necessary to observe whether the air release valve has an outflow, if there is, immediately tighten the air release valve, pay attention to the whole water inlet process must be patient, only in this way can the gas in the radiator be emptied, so that the radiator can be filled with water.

4. Follow the above steps to operate the radiators in each area of the home, wait until all the radiators are filled with water, then slowly open the exhaust valves and then slowly open the water inlet valves to ensure that the radiators in each corner are filled with water, and the opening and closing speed of the valve should be slow, from small to large.

5. Wait until all the radiators are filled with water, and then open the return valve slowly, as long as you hear the sound of water flow, stop to ensure that the speed of the water inlet valve is faster than the return valve, only in this way can the radiator be filled.

Winters in the north are cold, so every household is equipped with heating equipment, and radiators are one of the most common heating facilities. But there are also people who are unfamiliar with how radiators are installed. So how are radiators installed?Let's take a look!

Radiator installation is a high-tech work, if the installation is slightly careless will involve household property and personal safety, it is recommended to choose a professional team to complete. Generally, the installation location of the radiator is determined first, and then the pipe laying and transformation are carried out. Finally, install the installation diagram of the radiator.

First put the expansion screw and hook on the wall, put the radiator on the hook, and connect the valve with the pipe, so that the installation of the accompaniment is completed.

1. Determination of the installation position of the radiator.

Before installing the radiator, the installation position of the radiator should first be determined. It is usually installed under or near the window sill, so that in winter, when the cold air from the outside desperately drills into the room from the window crack, it is captured by the radiator, turning it into hot air and spreading it to all angles of the room.

2. Requirements for pipeline laying or pipeline transformation.

The connecting pipe of the general heating pipe should be selected in line with the national testing qualified plumbing products, the working pressure of the pipe and pipe fittings should be greater than the experimental pressure of the pipe network system, and the control valve should be installed for the inlet and return pipes of each group of radiators, and the pipe clamp needs to be installed every 300mm if the pipe is surface-mounted, and the casing should be installed if the pipe needs to pass through the wall.

3. Radiator installation method.

Before installing the heater, it is necessary to carefully check whether the type, color and accessories such as running wind, plugs, expansion nails, hooks and other accessories of the radiator are complete. First install the inlet valve and return valve, and then install it according to the installation diagram of the radiator. First smash the expansion screws and hooks in the wall, put the radiator back on the hook, and then connect the valve with the pipe, and the radiator installation is successfully completed.

The next step is to test the pressure. The test pressure should be times the normal use pressure and there should be no leakage for 3-5 minutes.

Summary: The above is the relevant content of how to install the radiator introduced to you, I hope to help friends in need. If you need to know more about related knowledge in the future, please pay attention to Qeeka Home.