Duck palm wood soil culture to hydroponics, unreliable, how to hydroponic duck palm wood?

Duck palm wood can be both soil and hydroponic. Compared with soil culture, rooting by pruning and soaking in water will be faster and easier to form seedlings. In order to speed up the rooting of water cuttings of the branches of the duck palm tree, we can either apply a little rooting powder to the base of the cuttings, or drop a few drops of rooting liquid in the water, and then wait for the rooting.

When the water cuttings have taken root and grown leaves, we can transplant the seedlings. So, how to transplant hydroponic duck palm wood?

Semi-lignified and leafy branches are cut from the adult tree of duck palm trees as cuttings, and then cut into branches about 10 cm long and with more than 2 nodes as water cuttings. At the same time, 1-2 compound leaves are kept at the upper end of the cuttings, and all the lower leaves are cut off to reduce water evaporation and nutrient consumption. Below insert the 2 3 part of the cuttings into a fully transparent glassware equipped with cold or mineral water.

After the cuttings are inserted, choose a bright and sufficient part of the room and place them. What needs to be done in the future is to control the temperature and change the water in the fish tank frequently.

According to the temperature of 15 or more, after the water change of the fish tank frequently, it is generally more than 10 days to see through the glassware that the bottom of the cuttings water part slowly produces a gray-white wound repair mechanism. After a few more days, you will find that the location begins to sprout adventitious buds. After about 50 days, most of the branches used for water cuttings will grow new roots about 6 cm long, and the original design will have white roots like hairs.

At this point, we can return to normal maintenance management steps.

However, water plugging is usually affected by the climatic environment, so it is generally necessary to prevent water plugging in the hot summer, and it is also necessary to prevent water plugging in the cold winter when the temperature is too low. Generally, the temperature in autumn and spring is very suitable for water cutting, and it is more suitable for water cuttings to breed duck foot wood seedlings. And the weather in these two seasons is basically maintained between 15 and 25, which is especially suitable for the root growth and germination stage of seedling cuttings.

After the success of the water plugging, we must do a good job in the corresponding maintenance and management work in a timely manner. The main thing is to change the water in the fish tank frequently, and at the same time control the temperature, moderate sunlight exposure, and generally accept diffused light to meet the needs of growth and development. In addition, we also need to do a moderate pruning work, because the growth and development of duck foot wood is relatively fast, and it is necessary to do a good job of pruning and plastic beauty during the maintenance management period.

However, if it is soil cultivation of seedlings with tap water, then it is necessary to choose a suitable opportunity to plant it in the flower soil in time. And the maintenance management, the same is mainly the work of light and soft fertilizer and water level.

If it is converted to hydroponics, it is necessary to use some water-soluble fertilizer and some organic water, and then it is necessary to change the water every once in a while to avoid water decay.

It is also known as the Fortune Tree by some people. Usually, the duck palm wood should be regularly supplemented with fertilizer. Hydroponic duck palm wood, I don't think it's very reliable, you must know that its own roots are grown in the soil, if it is directly hydroponic, then it is very likely that there will be rotten roots.

If you want hydroponics to grow wood, choose a branch with a higher hardness to cut it directly, cut off part of the leaves at the bottom, keep a main branch, add some water, find a container and put it in the container, and add some rooting liquid to the water.

In the process of cultivation, we should pay attention to the state of cultivation, nutrients, water, materials, and fertilization.

1. Rooting of branches: cut off semi-lignified branches from old plants, requiring 2-3 stem nodes with a length of about 10 centimeters, and the leaves of the upper part should be retained 1-2, and the leaves of the lower part should be cut off. After the branches are treated, the lower part of the branches can be put into a container filled with water, and the temperature is kept at about 15 degrees Celsius, and the roots can take root in about 10 days, and the roots will be stable and elongated after a month.

After the branches have taken root, they can be cultivated and protected by normal water.

2. Plant hydroponics: Duck palm wood can also change the soil culture plants to hydroponics. Remove the plant from the soil, then wash the roots with clean water and prune the roots to leave a healthy taproot so that it can absorb the nutrients in the water.

Prepare a transparent container and move the plants in so that the water level is just enough to submerge half of the roots. Pay attention to regular water changes, provide soft and bright sunlight, and add nutrient solutions dropwise to promote growth, and do a good job of maintenance to grow well.

Both hydroponics and soil culture are available, and it is impossible to say which method is better, so you can choose according to your needs. Hydroponics looks beautiful and is highly ornamental, saving some steps of watering and fertilization. Soil culture grows more stably and has an adequate supply of nutrients.

Duck palm wood can be hydroponics, the plant has a total of soil culture, hydroponic two cultivation methods, first use mineral water bottles or glasses as a container, and then cut the robust branches on the mother plant of duck palm wood, and cut the lower end into a flat mouth, remove the leaves, leave only the top 3-4 leaves, after the container is filled with water, put the duck palm wood in, and finally place it in the scattered light.

During the hydroponics period, not only can the growth of the root system of the plant be clearly observed, but also the ornamental value is relatively high, and the hydroponic method is relatively simple, basically will not breed insect pests, and the phenomenon of stem and leaf rot will occur.

When hydroponic duck palm wood, you should use a mineral water bottle or glass as a container, and then prepare a sharp pair of scissors to cut the strong branches on the mother plant of duck palm wood, and cut the lower end into a flat mouth, remove the bottom leaves, leaving only the top 3-4 leaves, and then fill the container with clean water, put the duck palm wood in.

After the hydroponics of the duck palm wood is completed, it should be placed in a place of scattered light, kept at room temperature of 15-25, and when the bottom of the cuttings grows 1-2 cm long white roots, it should be removed from the upper pot, or it can be moved into a more aesthetically pleasing glass container or transparent plastic container.

During the hydroponic duck palm wood, water quality is a very critical factor, only with the characteristics of clean, less bacteria, and more mineral elements, the plant can grow robustly, so it needs to be changed every 7-10 days, and the water quality is better with pure water.